ALDEN ALD-14096 User manual

ALD-14096
Installation and user`s guide
A.I.O.® EVO HD "All-In-One"
GmbH
DEUTSCHLAND
040417
178
ULTRAWIDE
V/H
ECO STANDBY
0.5W
3000 KANÄLE
VIDEOTEXT EPG MEHRSPRACHIG
DIGITAL
RECORDER
TIMESHIFT VIDEO AUDIO
LEDC B TV EPG
elektr. Programmführer
Vermieter
Mode

Contents
03 Warning instructions
05 Installation
06 TV description
07 Installation diagram with Alden automatic antenna
08 Installation diagram with Alden manual antenna
09 Installation diagram with a TWIN LNB
10 Use with Alden automatic antenna
11 Use with manual or semi-automatic antenna
12 Preparing the remote control
13 Remote control description and functions
15 Using the television
15 Basic features
15 How to use the system for the rst time (auto installation)
16 How to use in terrestrial mode
16 How to use with an external satellite receiver
17 How to use in DVD mode
17 How to use the multimedia player (media/USB*)
17 How to use the recording functions
18 Advanced functions
18 Picture menu
19 Sound menu
20 Channel menu
22 Feature Menu
24 Setup Menu
25 Troubleshooting
26 Technical specications
29 Alden warranty
30 Warranty form
Page 2

Warning instructions
The reproduction of whole or part of this guide is strictly forbidden without Alden’s approval.
Alden weist Sie auf die Risiken hin, die aus der nichtfachgerechten Montage erwachsen können. Alden übernimmt
keinerlei Verantwortung, wenn das Produkt nicht korrekt montiert wird und insbesondere nicht, wenn es von einem
Nichtfachmann installiert wird.
Alden draws your attention to the risks that may occur if the mounting is not correct. Alden declines all responsibility
if the product is not mounted in the correct way and especially if it is installed by a non-professional person.
The retailer is meant to know installation rules and to apply them. He will especially respect the installation location,
the cable connection, the gluing and screwing. By selling and installing an Alden product, the retailer is obliged to
inform his customer on how the product works and perhaps how to install the product in some cases. He will also
provide the customer with all relevant documents. The retailer will inform the customer about security matters. The
retailer must inform the end user on how to use an Alden product and the applicable safety measures. The product is
to be used only for the intended use. The retailer must also inform the end user about the current laws applicable in
the country where the product is going to be used.
Each product with electronic components has to be protected from undervoltage (below 10.5 volts) and overvoltage
(over 15 volts).
It is strictly forbidden to open, interfere with, repair and/or modify the product without Alden’s consent. The warranty
will become void if you undertake such an action.
Neither the salesperson nor the manufacturer can be held responsible if a satellite or a programme come to disappe-
ar, if a free-to-air channel becomes scrambled or for any other modication that may aect the emission.
Unpredictable events will not lead to any exchange, refund or compensation from the salesperson nor the manufac-
turer. The reception areas of the satellites are given as a guidance.
Alden declines all responsibility in the event of incidents or accidents if they are due to non-observance of the instal-
lation instructions or the way the product is used.
Remove the fuse from the electric circuit board of the satellite system and receiver before interfering on the general
circuit board, or changing or connecting the battery. If the vehicle is equipped with a solar panel, also remove the
fuse.
Keep away from children.
You must install separate cables with a 5-amp fuse on the plus line, directly from the cell battery to the television.
Before interfering on the electric circuits, make sure the specications of the device and the electric circuit are com-
patible.
For a good quality picture, do not use the existing coax cables. In general, it is best to avoid connections.
You must protect the ends of the motor and coaxial cables with paper tape during installation (especially when threa-
ding the cables through furniture).
Do not drop or push objects into the television, the slots or the openings. Do not spill liquid on the television. Do
not open or touch the inner circuit. Do not remove the back cover: only a qualied professional is allowed to do so.
Do not use the television if the power supply cables or connections are damaged. Never lay anything on the cables.
Make sure that the cables cannot be pulled o and that no one will stumble over them. To unplug a cable, hold the
plug and not the cable.
The openings are to ventilate the television. They have to stay free. Never lay the television on a bed, a sofa or any
other soft surface. This can block the openings and stop the television from being ventilated. If you install the televi-
sion in a closed area, make sure the ventilation is sucient: there must remain a 20cm space around the television to
ensure sucient ventilation.
Do not expose the television to rain or water (kitchen, bathroom...). If this ever does happen, immediately disconnect
the television from the power supply and contact your retailer.
Only use approved or the original spare parts recommended by your dealer, otherwise the warranty will become
void. Work on the unit must be performed by qualied technicians.
Page 3

Install the television in a place where it will not be aected by humidity, dust, and on a at and stable surface. Use the
device carefully. The screen is made of a thin layer of glass, it is therefore sensitive to shocks, scratches... Do not clean
with corrosive products. Simply use a slightly damp, soft cloth.
Do not place magnetic products (like loudspeakers...) near the television.
In case of dysfunction (unusual sound or smoke...), immediately disconnect the television from the power supply and
contact your retailer.
A high ambient temperature may cause the television to dysfunction. Do not use or store the television in direct sun-
light or near a source of heat. If the ambient temperature is too low, the quality of the picture may be aected. If this
is the case, switch the television o and wait for a few minutes. If the problem remains when you switch the television
on again, change the ambient temperature.
Unplug the television from the power supply before interfering with the television.
Only use the base sold with the device. The television must be moved carefully. It may fall when braking, in case of
fast acceleration or when driving on damaged roads. Never install the television in a place where it will be in direct
contact with sunlight, high temperatures, high humidity or a lot of dust: this could damage the internal parts of the
television. Place the television on a stable surface and handle with care.The screen is made of glass and can be dama-
ged if dropped in case of collision, or scraped.
When the television is not used during a long period, disconnect the power supply.
In case of dysfunction (unusual sound or smoke...), immediately disconnect the power supply from the television
and contact your retailer. Unplug the television from the power supply before attempting to repair it. Make sure the
technician uses authorized spare parts. If these parts are not conform they may cause re, electric shock or other
dangers. Follow all the maintenance and repair instructions, make sure the technician controls all security devices to
ensure that the television can be used without danger.
• By installing this product, you accept the above conditions. •
WEEE Directive (European Union and EEA only).
This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Di-
rective (2002/96/EC) and your national law. This product should be handed over to a designated collection point, e.g.
on an authorized one-for-one basis when you buy a new similar product, or to an authorized collection site that recycles
waste electrical and electronic equipment (EEE). Improper handling of this type of waste can have a negative impact on
the environment and human health due to potentially hazardous substances that are generally associated with EEE. By
respecting this directive, you will contribute to the eective usage of natural resources. For more information about where
you can dispose of your equipment for recycling, please contact your local city oce, or other authority, approved WEEE
scheme or your household waste disposal service.
(EEA: Norway, Iceland and Liechtenstein)
Page 4

Installation
Connecting the televison to other devices
HDMI
USB
Mini AVM ini YPbPr
CI-Slot
Earphone
DC IN
VGA
SCART PC Audio
S2 T2
COAX Out
VOL+ VOL-
CH+ CH-
SOURCE
MENU
è
D
NO
MOTOR
CONTACT
LNB IN OUT TO
DEMO
RCA adaptor
audio-video
connection
(yellow / white / red)
YUV adaptor
video connection
(red / blue / green)
USB cable
(not supplied)
HDMI cable
connection
HD audio-video
(not supplied)
LNB IN: Coaxial
cable to
connect to your
satellite dish
VGA
Video
connection on a
computer.
(not supplied)
Scart cable
connection
SD audio-video
(not supplied)
Terrestrial input
DVB-T
D+
(for automatic
Antenna only
Motor cable
(for automatic
Antenna only)
Allows to maintain
the cables during
manipulations with
AIO TV.
Page 5

TV Description
1 VOL - Lower the volume.
In a menu, move the selection to the left
2 VOL + Increase the volume.
In a menu, move the selection to the right
3 CH - Display the previous programme number
In a menu, move the selection to the bottom
4 CH + Display the next programme number
In a menu, move the selection to the top
5 MENU Display the main menu. In a sub-menu, return to the previous menu.
6 SOURCE Display the source list
7 EJECT Eject the DVD
8 PLAY/PAUSE Switch between Play and Pause
9 POWER Switch on / put in standby.
10 ON/OFF ON/OFF switch on the lower side of the frame
11 POWER INPUT TV 12 volt power supply
12 VGA IN Video connection on a computer.
13 SCART SCART cable connection
14 PC AUDIO IN Computer connection
15 S2 Connection to the coaxial digital cable DVB-S/S2
16 T2 Connection to the coaxial cable from a DVB-T / MPEG4 antenna
17 COAX Out Connection of the audio coaxial cable
18 LNB IN Used to connect the coaxial cable of the satellite antenna.
19 OUT TO DEMO -
20 CONTACT Used to connect D+ contact with an Alden automatic antenna. WARNING:
The line must be protected by a 3 A fuse.
21 MOTOR Used to connect the motor cable of an Alden automatic antenna.
22 HDMI IN Connection to a high-denition multimedia device.
23 USB USB port in TNT or media mode
24 CI CA-Module Slot (Conditional Access Module) Ci+ compatible
25 YPbPr IN Connection to a multimedia device.
26 AV IN Connection to a multimedia device (RCA).
27 EARPHONE OUT 3.5mm stereo audio output (earphone).
28 DVD-Player DVD. Insert the disc printed side facing the back.
29 Red: TV in stand-by mode; green: TV on
Integrated infrared sensor
Page 6
+

Coaxial cable Motor cable
D+ contact (this line must be
able to deliver 1.5 A min)
Installation diagram with Alden automatic antenna
Attaching the antenna cables
In order to ensure that the antenna cables are properly secured, the motor cable and the coaxial cable must be placed
in the appropriate housing, which must be closed with the supplied screw.
NOTE: there are 3 possible cable entry solutions. Connect the 2 cables to the matching inputs depending on the
conguration of the TV set.
Power supply connection
Once all the devices have been connected to the TV, you can connect to power supply:
Check the power supply polarity:
- Connect the wire to the ground.
- Connect the wire directly to the plus pole on the cell battery.
Caution: the wire must be protected with a 5 Amp fuse.
Insert the power cord into the 12 V DC output on the TV.
-
+
+
Page 7

Attaching the antenna cables
In order to ensure that the antenna cables are properly secured, the motor cable and the coaxial
cable must be placed in the appropriate housing and close it with the supplied screw.
NOTE: there are 3 possible cable entry solutions. Bring 2 cables to one of the inputs depending
on the conguration in which the TV is installed.
Power supply connection
Once all the devices have been connected to the TV, you can connect to power supply :
Check the power supply polarity:
- connect the wire to the ground.
- connect the wire direclty to the Plus on the cell battery.
Caution : the wire must be protected with a 3 Amp fuse.
Insert the power cord to the 12 V DC on the TV.
-
+
+
Coaxial cable
Installation diagram with Alden manual antenna
Page 8

Power supply connection
Once all the devices have been connected to the TV, you can connect to power supply:
Check the power supply polarity:
- Connect the wire to the ground.
- Connect the wire directly to the plus pole on the cell battery.
Caution: the wire must be protected with a 3 Amp fuse.
Insert the power cord into the 12 V DC output on the TV.
Installation diagram with a TWIN LNB
To head LNB
TWIN or antenna
positioner of
another brand.
Coaxial cable
CAUTION: The installation diagram above applies in case the AIO TV SATMATIC-HD
is connected to the second coaxial output of an antenna equipped with an LNB TWIN or if
it is connected to a satellite pointing module of another brand.
Page 9
-
+
+

Commissioning of your satellite system.
1. Make sure that the antenna can stand and rotate without encountering obstacles (branches, buildings, telephone
relays, etc.) during reception or operation.
2. Switch the main switch located on the underside of the AIO SATMATIC-HD to position 1 (on) to turn the power on.
3. Activate your AIO SATMATIC-HD by pressing the button on your remote control. The start-up phase can last up
to 30 seconds. If your antenna is not yet oriented, the antenna will rise and orient itself automatically. The system is
pre-programmed to automatically start the search on the last selected satellite. During this automatic search operation,
the antenna pointing information bar is displayed:
Commissioning of your satellite system
When the automatic antenna orientation is successful, a double beep will sound and this information bar will be
displayed for 10 seconds and then disappear automatically in the absence of manipulations on your part with the remote
control. The start-up phase of your AIO TV then continues until you get an image.
• (green) Satellite: Allows to change satellite.
• (red) Close: Allows the automatic antenna to be closed.
• (blue) Info **: Informs about the conguration of your TV AIO.
• (yellow) Diag **: Informs about the parameters of your automatic antenna.
** The satellite cannot be found when this function is requested.
Anm. d. Übers.: Klingt unverständlich. Was genau ist hier gemeint? Vielleicht besser so:
** This function is required if the satellite cannot be found.
IMPORTANT: When using the system for the rst time, or during large trips, it is possible that the search takes more time.
WARNING: Activating the vehicle contact prevents manipulation of the antenna. Check that the vehicle contact is
deactivated.
NOTE 1: During the automatic search phase of the satellite, it is possible to control the antenna manually by using the 4
directional buttons on the remote control. Pressing the OK key will restart the search in automatic mode.
NOTE 2: When a satellite channel is displayed on the screen, it is possible to display the satellite search menu again by
pressing the green button on your remote control.
At the end of use
1. Press the button on your remote control. Then select the action to be performed on your antenna.
2. The AIO SATMATIC-HD then switches to standby mode (consumption <1W).
3. Switch main switch to 0 (o) to turn o the power.
WARNING: The warranty is void if you forget to fold the antenna.
Page 10

Use with manual or semi-automatic antenna
Commissioning of your satellite system
1. Make sure that the antenna can stand and rotate without encountering obstacles (branches, buildings, telephone
relays, etc.) during reception or operation..
2. Switch main switch located at the bottom of the AIO to position 1 (on) to turn the power on.
3. Activate your AIO with the button on the remote control. It turns on and remains on standby for the transmitted
signal by the satellite selected for manual search. The following information bar appears on the screen:
4. Refer to your antenna's instructions for positioning. The AIO SATMATIC-HD TV emits a continuous beep when the
satellite is locked. Adjust the position of your antenna to obtain the best power (P) and Q (quality) possible. Press the
EXIT button on the remote control to stop the continuous beep sound from the AIO SATMATIC-HD.
• (green) Satellite; Allows to change satellite.
• (blue) Info **; Informs about the conguration of your AIO TV.
The satellite cannot be found when this function is requested.
NOTE: When a satellite channel is displayed on the screen, it is possible to redisplay the "satellite search" menu above by
pressing the green key on your remote control.
At the end of use
1. Press the button on the remote control to switch the AIO SATMATIC-HD to standby.
2. Refer to your antenna instructions for folding.
3. Switch the main switch to 0 (o) to turn o your AIO SATMATIC-HD.
Page 11

- Remove the battery cover on the back side of the remote control.
- Put 2 new 1.5 V AAA batteries in place: make sure polarity is correct.
- Put the cover back in place.
Caution:
- A non-conform use of the batteries can cause leaking and corrosion.
- Do not install the batteries in the wrong way.
- Do not charge, open, overheat nor short-circuit the batteries.
- Do not throw the batteries in the re.
- Do not leave old batteries in the remote control.
- Do not use dierent kinds of batteries, for example an old battery with a new one.
- If the remote control is not used during a long period, remove the batteries.
- If the remote control does not function or if you have to be near the TV to use it, replace
the batteries.
- If the batteries have leaked, clean the compartment and the connectors and put new
batteries in place.
Preparing the remote control
How to use the remote control
- Point the remote control towards the television when using it.
- Avoid damaging the remote control.
- Do not leave the remote control near a source of heat or humidity.
- Do not spill water or leave anything damp on the remote control.
- Do not open the remote control.
Page 12

POWER Turns the AIO SATMATIC-HD TV on or o
MUTE Press once to switch the sound o
Press a second time to active the sound
P.MODE Press several times to select a picture pre-setting.
S.MODE Press several times to select a sound pre-setting.
SLEEP Press several times to programme the TV to switch o automatically.
1...0 Use these buttons to select your channel.
-/-- Quickly set a channel that has more than 2 digits.
D.ZOOM In MEDIA mode, activate the search functions.
SOURCE Use this button to display the menu for selecting video sources.
EJECT In DVD mode, enables to eject the DVD.
▲▼◄► Use the arrows to navigate in the menu and record the settings.
OK Press to conrm your choice
MENU Press to display the main conguration menu. In a sub-menu, press once to
return to the previous menu.
D.SETUP
EXIT
Press to enter the main menu and set the DVD player.
Press to exit from a menu.
▲VOL▼Use to increase / lower the volume.
DISPLAY Display the source and information on the current channel.
ASPECT Press several times to change the picture ratio.
▲CH▼Use to go to the next / previous programme.
PROGM
(rot) A selection according to the action described in the displayed menu
GOTO
(grün) In DTV satellite mode, this key allows to change to a satellite from the list.
Remote control description and functions
A-B
(yellow) Press to activate the playback on segment A-B (DVD).
ANGLE
(blue) A selection according to the action described in the displayed menu
TEXT
►ΙΙ
Press once to display the teletext of the watched programme, press again to return to a plain
background
Switch between play and pause
SIZE
■
Press to change the size of the teletext page (normal, ½ -page sup., ½ -page inf.)
Press to stop playing (DVD, media).
Page 13

Remote control description and functions
HOLD
◄◄
Press once to not update the current teletext page, a second time to launch
the automatic update.
Press to rewind (DVD, media).
INDEX
►►
Press to display the index page of the teletext.
Press to fast forward (DVD, media).
REVEAL
Ι◄◄
Display the information hidden on the current teletext page.
Press to return to the beginning of the DVD chapter / previous media.
SUBPAGE
►►Ι
Display/hide the sub-page.
Press to go to the next DVD chapter or next media.
REPEAT Press to select a repeat mode (DVD or media).
SUBTITLE Display the list of subtitles available in DVD mode.
LANG
D.AUDIO
View Multi Audio List
EPG Press to display the EPG (in terrestrial mode only)
REC Press to record a digital terrestrial programme on a USB device.
TV/RADIO
D.DISP
Switch between TV and Radio mode (DTV source only).
Press to display the information bar of the currently playing DVD.
FAV
D.MENU
Display the favourite channel list.
Press to access the main menu of the currently playing DVD.
T.SHIFT
D.TITLE
Switch to Timeshift mode.
REC.M Click to add / edit / delete a recording
*: USB media not supplied.
Page 14

Using the television
Basic features
Press on Source to display the list of video inputs.
Use ▲and▼to select the input that you wish to watch:
DTV Digital satellite TV
(DTV-S/S2) SCART SCART (SD) PC Computer (VGA)
ATV Digital terrestrial TV
(DTV-T/MPEG4) YPbPr Composite input (SD) MEDIA Multimedia Player
AV Analogue input (SD) HDMI HDMI input (HD) DVD DVD-Player
Press Enter to conrm your choice.
Basic functions in the menus:
Use Menu to display the main menu / return to the previous menu in the sub menu.
Use ▲▼◄► to navigate in the menu.
Use ►to display the values to be set in the sub menu.
To undergo a modication, use ▲and ▼in a list, ◄and ►with an adjustment bar.
How to use the system for the rst time (auto installation)
When switching the system on for the rst time, a quick installation guide will appear. These instructions will
enable you to do the basic settings and the initial search for the programmes broadcasted in terrestrial mode.
1. Check the country. If the pre selected country is correct, press (green) to go to the next step. Otherwise,
use ▲and▼to alter the selection and press Enter to conrm your choice.
2. Check the language in the menus. If the pre selected language is correct, press (green) to go to the next step.
Otherwise use▲and ▼to alter the selection and press Enter to conrm your choice.
3. Choose the location of installation on the TV. The proposed choices enable to pre select the picture settings.
Use ▲and ▼to alter the selection and choose the most adapted and Enter to conrm your choice.
4. Check the automatic TV switch o. By default, the TV is programmed to switch o after 4 hours of viewing. If
the pre selected choice is convenient for you, press (green) to go to the next step. Otherwise, use ▲and▼to
alter the selection and Enter to conrm your choice.
5. Select the desired level of protection in the parental control menu (O, from 3 to 18). press Enter.
6. In the TV connection menu: the Satellite mode allows to set up your TV set with a satellite channels list. Select
the Terrestrial mode to set up your TV set in terrestrial reception, or the Cable mode to set up your TV in cable
reception. For a recreational vehicle, it is recommendable to use the Satellite mode.
Page 15

7. Change PIN code: allows you to change the PIN code.The PIN code is a 4-digit code. To change this code, enter
the old code (8008 by default), the new code you want, the new one second time for conrmation. A message
appears conrming the PIN code change.
8. Your TV is now installed. To use the system in DVB-S satellite mode: Press source>TNT, you can see a pre-pro-
grammed channel list by pressing Enter.To switch to DVB-T mode, refer to the channel menu. Choose TV Connec-
tion and select the antenna mode, then launch a search for a channel as described in chapter“Automatic channel
search”. (page 21)
How to use in terrestrial mode
Press Source to display the list of video sources. Use ▲and ▼to select
- ATV to watch analogue programmes (no longer available). Important information: Since November 30th 2011,
no more analogue signal is broadcasted in France.
- DTV to watch digital programmes (terrestrial or satellite). Then press Enter to conrm your choice.
When watching a programme, the main following features are available:
• Ch+/-: go to the next / previous programmes
• 0...9: display a programme by entering the number.
• Vol+/-: increase / lower the volume.
• Fav: display the favourite channel lists.
• EPG: display the EPG (digital terrestrial mode only).
• Display: press once to display limited information, press twice to display all the information corresponding to
the watched programme, press a third time to remove the display.
• TV/Radio: switch between TV and Radio mode (digital terrestrial mode only).
Other features are available in terrestrial television mode. Refer to pages 20.
How to use with an external satellite receiver
Press Source to display the list of video sources. Use ▲and▼to select :
- AV if your satellite receiver is connected to the TV with a RCA cable (white - yellow - red).
- SCART if your satellite receiver is connected to the TV with a SCART cable.
- YPbPr if your satellite receiver is connected to the television via a YUV cable (blue - green - red)
- HDMI if your satellite receiver is connected to theTV with a HDMI cable.Then press Enter to conrm your choice.
To receive satellite channels with your external satellite receiver it is necessary to switch on the DTV source to
align your antenna to the satellite. After pointing switch back to the HDMI source to display the contents of your
external receiver.
CAUTION: In order to close the automatic antenna, it is also necessary to select the DTV source.
Refer to the chapters on pages 10/11 for the use of your AIO TV with an Alden automatic antenna or manual
antenna.
Information:
Each time you switch the system on, the TV will automatically select the last chosen source.
Page 16

Important information:
Handling a DVD can only be done once the DVD mode has been selected. It is not possible to insert or eject a DVD if
another mode is selected.
Press Source to display the list of video sources. Use ▲and▼to select DVD then press Enter to conrm your choice.
The DVD player will unlock.
Insert the DVD in the DVD player, printed side towards the back of the TV. The DVD will start automatically.
Use ▲▼◄►to navigate in the interactive menus and conrm your choice by pressing Enter.
Other functions are available in DVD mode. (See pages 18  )
How to use the multimedia player (media/USB*)
Press Source to display the list of video sources. Use ▲and▼to select Media and then press Enter to conrm your
choice. The File Manager will be displayed.
You can also access this menu by pressing Media on your remote control.
How to use in DVD mode
Use ▲and ▼to select the type of media and press Enter to conrm.
To navigate in the USB device, use ▲and▼to go up / or down in the list, ◄and►to enter / exit a sub-menu and Enter
to start reading the selected le.
When navigating, press Exit to return to the main screen (choose the type of le).
- Photo: read pictures
- Music: read audio les
- Movie: read video les
- E-Book
To exit the menu, press Source to display the list of video sources.
How to use the recording functions
Important information
The recording functions are only available on the DTV source (terrestrial digital).
When a compatible USB key* is connected to the TV, it is then possible to record programmes and control the live
programmes.
The USB support must be inserted in the TV before you are able to use the recording functions
Fast recording
Press Rec to start recording the watched programme. The programme will continue to be broadcasted. Press ■to stop
recording. The recorded programmes are accessible via the Media source, PVR menu.
Direct / Timeshift
Press Timeshift auto to start recording the watched programme. Press ►ΙΙ to pause. Press ►ΙΙ to start watching the
programme again but in deferred mode. When watching the programme, you have the possibility to fast-forward or
rewind the programme by pressing ◄◄ or ►►. Press ■to return to the direct mode. Press Timeshift to stop recording.
You will nd these functions, and the advanced recording functions in the dedicated menu, PVR / Timeshift sub menu.
*(not supplied)
Page 17

Important information
The settings and modications made in the menus are only valid for the current source. This enables you to customize
each source (TV, DVD,...) depending on your needs.
Picture menu
Advanced functions
Picture mode
Once selected, press ►to display the list of available pre-settings. Use ▲and ▼to make your choice and press Enter to
conrm your choice (Standard; Optimal; Bright; Soft; User).
The User mode enables you to customize the brightness, contrast, sharpness and colour settings.
Brigntness
Once selected, press ►to display the setting options. Use ◄and►to make your choice and press Enter to conrm
(from 0 to 100).
Contrast
Once selected, press ►to display the setting options. Use ◄and ►to make your choice and press Enter to
conrm (from 0 to 100).Schärfe
Sharpness
Once selected, press ►to display the setting options. Use ◄and►to make your choice and press Enter to conrm
(from 0 to 100).
Color
Once selected, press ►to display the setting options. Use ◄and►to make your choice and press Enter to
conrm (from 0 to 100).
Tint
Once selected, press ►to display the setting options. Use ◄and►to make your choice and press Enter to
conrm (from 0 to 100).
Page 18

Colour temperature
Once selected, press ►to display the setting options. Use ▲and▼to make your choice and press Enter to
conrm (Standard; cold; warm).
Aspect ratio
Once selected, press ►to display the setting options. Use ▲and ▼to make your choice and press Enter to
conrm.
Noise reduction
Once selected, press to display the available presets list. Use and to make your choice and press Enter to conrm (O,
Low, Medium, High).
Sound Mode
Once selected, press ►to display the available pre-settings. Use ▲and▼to make your choice then press Enter to con-
rm (Standard; Movie; Music; Speech; User).
The User mode will enable you to customize the sound.
Bass
Once selected, press ►to display the available pre-settings. Use ◄and ►to make your settings and press Enter to con-
rm (from 0 to 100).
Treble
Once selected, press ►to display the available pre-settings. Use ◄and ►to make your settings and press Enter to con-
rm (from 0 to 100).
Balance
Once selected, press ►o display the list of setting options. Use ◄and►to make your choice and press Enter to conrm
(from -50 to +50).
Page 19

Surround
Once selected, press ►to display the dierent options. Use ▲and▼to make your choice and press Enter to
conrm (O ; On).
AVL
Once selected, press ►to display the dierent options. Use ▲and▼to make your choice and press Enter to
conrm (O ; On).
SPDIF
Once selected, press ►to display the dierent options. Use ▲and▼to make your choice and press Enter to
conrm (O ; MIC ; Auto ; Multi).
Channel Menu
Channel Management
Once selected, press Enter to access the channel management sheet. Use ▲and▼to navigate in the list and select the
channel that you wish to alter. You can use:
• (red) to erase a channel;
• (green) to lock / unlock a channel;
• (yellow) to activate / deactivate a channel skip;
• (blue) to swap the position of a channel with another channel in the list;
• Enter to rename a channel (a keyboard will appear).
When exiting the sub menu, a conrmation window will ask you if you wish to save the modications or not.
Page 20