All American Scoreboards 8000 Series User manual

Firmware Version 2.21+,3.21+
rev. 9/9/09

Manual Overview
This manual is intended for the use of the All American Scoreboard owners and
users. Read this manual carefully before starting the equipment.
This manual contains important information for operation and maintenance of the equip-
ment. It also contains important instructions to prevent accidents, personal injury and/
or serious damage prior to or during operation of the equipment.
Familiarize yourself thoroughly with the function and operation of this equipment and
strictly observe the directions given. If you have any questions or need further details
on specific aspects related to the AAS system, please do not hesitate to contact us.
In this manual you will find three levels of flagged notes or warnings.
WARNING!       
      

CAUTION! 


NOTE:
Table of Contents
1.0 8000 Series Multi-Sport Console .................................................................................................... 3
1.1 Console Backplate ........................................................................................................................................................ 3
1.2 Console LCD .................................................................................................................................................................... 4
1.3 Console Keypad ............................................................................................................................................................. 5
2.0 Scoreboard ID and Scoreboard Selection (Radio) ......................................................................... 6
2.1 Selecting Scoreboards ............................................................................................................................................... 6
2.2 Additional Radio Information / Changing Scoreboard ID ............................................................................. 7
2.3 Advanced ID Changing Scenarios .......................................................................................................................... 8
2.4 Scoreboard Type ........................................................................................................................................................... 9
3.0 Console Keypad Functions ............................................................................................................ 10
3.1 Setup ..............................................................................................................................................................................10
3.2 Racing Operations .....................................................................................................................................................12
4.0 Safety .............................................................................................................................................. 13
5.0 Warranty ......................................................................................................................................... 14
6.0 Technical Support .......................................................................................................................... 15
6.1 Customer Service ........................................................................................................................................................15
6.2 Contact Information ...................................................................................................................................................15
2

3
STORING:
Battery should be fully charged when storing, and should be kept at room temperature.
Recharging once every 30 to 45 days of storage is recommended. If batteries are stored
longer, it may take two or three cycles before full run time is restored.
The 8000 Console Backplate.
WARNING! This equipment has been approved for mobile applications where
equipment should be used at distances greater than 20cm from the human body
(with the exception of hands, wrists, feet and ankles). Operation at distances less
than 20cm is strictly prohibited. Excessive RF exposure should be avoided.
Setup Instructions:
Press once to turn on.
Follow prompts on screen.
Press and hold to turn off.
TRANSMITTER MODULE FCC ID:KQL-PKLR2400-200 IC:22683911808A3 17
WARNING! This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
RJ45 RJ45 RJ45 RJ45 RJ11 RJ11
Radio Controlled Units Only
Radio Antenna
Radio Antenna screws into the backplate
above the Timer Pendant Switch.
For best results, aim antenna straight up to
the ceiling or sky - do not aim directly at
scoreboard.
AC Adapter
Plug the
supplied 12VDC
adapter into a
standard
115VAC outlet.
Scoreboards
For hard-wired models only, plug the scoreboard(s) into the console using
an RJ45 connector. Plug in all hard-wired scoreboards, shot clocks, delay of
game timers, segment timers and stat panels here.
Security Key | Auxiliary I/O
Used to connect consoles together for use with stat panels, etc.
Timer Controllers
Plug in seperate All American consoles that control shot clocks, delay of
game timers, etc here using an RJ11 connector.
USB (Console V4.00+ Only)
Connect to a computer to update console version and advanced console
setup functionality.
Pendant Switch
Plug in the pendant switch to bypass
the start/stop key for the timer.
Adapter LED
Orange = Adapter is good.
Red = Adapter supplies
enough power to run, but not
enough to charge the battery.

The 8000 Console.
LED Windows
Displays crucial troubleshooting and
functional information at a glance.
Power.
Clock.
Stars turn white when console is turned on.
Clock symbol lights up green when clock timer
is running. Turns off when clock is stopped.
Battery.
Battery symbol displays a constant red when
charging a battery. Battery symbol turns green
or turns off when charged for 3 hours.
Wireless.
Wireless symbol will light blue when a the
battery is connected. Light will flash if antenna
is disconnected.
Horn.
If autohorn is selected in setup, the horn
symbol will light up in an amber color.
If autohorn is not activated, the symbol will
only light when horn is pressed.
LCD Window
Displays game information in a convenient and easy to
read 2x20 character matrix.
Also displays game stats and setup information.
Typical Gameplay Display
14 2Q 10:54 10
<P 2& 6 on37
HOME
SCORE QUARTER GAME TIME
GUEST
SCORE
HOME
POSS.
DOWN YARDS
TO GO
BALL
ON
Low Battery Display
Low battery message will flash in the lower part of
display when battery time is below 15 minutes. Plug the
console in using the 12VDC plug as soon as possible.
A low battery may require multiple charges before
operating at 100% capacity.
The RADIO will be the first component to stop
working when battery is low.
14 2Q 10:54 10
* * * LOW BATTERY * * *
4

The 8000 Console Keypad.
Slipsheet Window and Message Center Keys
Our console is designed to run any 8000 Series
Scoreboard. Simply insert the correct slipsheet under the
window and tell the console what sport you are scoring
and what scoreboard you are using.
Each slipsheet also has an instruction sheet to help get
you started; simply pull out the slipsheet, unfold and
insert with the instructions hanging from the bottom.
Tactile keys give instant feedback and help eliminate
double presses.
Below the slipsheet window is a fully functioning
standard keyboard style keypad, perfect for running a
message center or for entering electronic team names to
display on your scoreboard (select models only).
Number Keypad.
Used in pregame and
gametime operations. Use
these to enter in player
jersey numbers, change
scoreboard information,
and to edit scores, time, etc.
Use the “clear” key to exit
out of a function.
Use the “enter” key to
finalize a command.
Setup.
Used in pregame and gametime
operations. Set brightness of
scoreboard, length of time-out, etc.
Press to enter setup mode at any
time when clock is stopped.
Select and Arrow Keys.
Use the arrow keys to select different
options or answers displayed in the
LCD. Press YES/NO to toggle answer
between Yes and No.
Horn.
Press this button to sound the horn
(if scoreboard is equipped with a
horn). The horn will sound, the
console will beep, and the LED
symbol will light (see previous page).
Timer Start/Stop (embossed).
Press this once to start the clock and
again to stop the clock. If a pendant
switch is used, the clock can be
started and stopped by pressing the
button on the pendant switch.
On/Off.
Press once to turn on.
Press and hold to turn off.
5

Selecting Scoreboards (Radio Units Only). FIRMWARE VERSION 2.00 AND ABOVE.
The 8000 Series Console is a powerfull and intelligent scoring machine. A single console, for example, can
keep score for football in the fall, basketball in the winter and baseball in the spring. This machine can also
select any 8000 scoreboard or message center you have in your facility.
Each time you order a scoreboard, it will be issued an identification number. If you have multiple 8000 series
scoreboards, the ID number will be an important part of your scoring system.
STEP 1: Turn on Scoreboard(s).
Turn on your scoreboard(s) by simply supplying power.
For most facilities, this will simply be a switch or multple
switches in a circuit breaker box.
Step 2: Turn on your console.
Step 3: Press 1 for scoreboard operation.
Step 4: Press to change the answer from “Yes” to “No”, and then press .
Step 5: Enter Scoreboard IDs (read below).
The screen above will appear when “Use last setup?” is answered “No.” Every 8000 Scoreboard that was turned
on and not currently in use will display the scoreboard ID in the seconds place and/or the guest score of the
scoreboard (home score for baseball). If your scoreboard displays both time and scores, the ID will be
displayed in both locations. Any other information displayed can be ignored.
Enter the ID code displayed on the desired scoreboard and press . If selecting more than one scoreboard,
enter the next ID followed again by . When finished selecting boards, press . Next, select the sport to
be played (see setup).
ADDITIONAL INFORMATION:
Once the boards have been selected, the console and all selected scoreboards will switch from their default
channel to another channel. The ability to switch channels allows the unselected scoreboards to be selected
by another console - making it easy to run multiple sporting events at the same time. If a scoreboard is not
chosen, it will either display time of day or appear to be off (see setup).
IMPORTANT: SELECT BOARDS WITH ONLY ONE CONSOLE AT A TIME.
If multiple consoles will be used, select boards with one console before turning on second (third, fourth, etc.)
console. Since each console will start on the same default channel, the signal from the consoles will fight each
other, and will likely result in failure and interference. Once the selection process is completed and a sport is
selected, another console can be turned on. Scoreboards that are in use will not display their IDs and will not
respond to any requests by other consoles.
For detailed examples and information regarding changing IDs, see next page.
Enter Scoreboard IDs
ENTER when done _
1. SCOREBOARD
2. STATPANEL ->
Use Last setup? _No
Bask 1 Board
ID=1,
ENTER when done
Use Last setup? _Yes
Bask 1 Board
FIRMWARE DISPLAYED
HERE ON STARTUP
6

Changing the Scoreboard ID. (Radio Units Only - Console Firmware 2.00 and Higher)
All American Scoreboards assigns each scoreboard an ID number that can range from 1 to 19. Because our
scoreboards can be purchased at different times or through various vendors, we cannot be certain that your
scoreboards will not have the same ID number. If two or more scoreboards have the same ID, the boards will
always run in dual mode (more than one scoreboard controlled by one console) unless the circuit breaker to
one of the scoreboards is turned off.
NOTE: YOU WILL LIKELY NEVER NEED TO SET YOUR SCOREBOARD ID. DO NOT CONTINUE WITHOUT
READING AND UNDERSTANDING THE FOLLOWING INSTRUCTIONS.
STEP 1: Turn on the scoreboard to be changed by simply supplying power.
For most facilities, this will be a switch in a circuit breaker box. If more than one scoreboard is connected to
one circuit, any scoreboard that is connected to the circuit and not in use will be set to the same ID,
making running the scoreboard individually impossible. AAS recommends changing the ID before instal-
lation of a scoreboard to a circuit where multiple 8000 series scoreboards are connected. If it is not possible to
turn off power to one of the scoreboards, see Advanced ID Changing Scenarios.
Step 2: After the firmware version is displayed (must be 2.00 or above), press both arrow keys simultane-
ously (in console mode selection screens). Because it is difficult to press 2 keys at the exact same time, multiple
attempts may be required.
Step 3: Enter Passcode. Default passcode is 12345. AAS recommends that the passcode be changed to
prevent the scoreboard from being altered accidentally. If the passcode is forgotten, call 1-800-356-8146.
Step 4: Once a passcode is entered correctly, additional options will be available. Press arrow keys to see
additional options.
Step 5: Press the number 6 to change IDs.
Step 6: Set a scoreboard ID (from 1->19) and press enter. Unless the scoreboards will always be run in dual
mode, make sure that the ID is unique to all other scoreboards. The scoreboard will restart itself. Wait for
scoreboard to run through startup sequence before continuing to scoreboard type.
Step 7: When asked for scoreboard type, press enter. This will leave the type unchanged. If type needs to be
changed (not common), refer to Scoreboard Type on next page. Enter 3 digit type number and press enter.
To select the basketball boards, the IDs would be entered by pressing
To finish selecting, press again.
NOTE: ID 14 was not entered, because this is a volleyball scoreboard. Once selections are complete, the non-
selected boards will either blank or display the time of day. If a volleyball match is played in the same facility
at the same time, another console can ask for the ID and the process can be continued. Once a board is
selected, another console cannot ask for the ID of a scoreboard in use.
All IDs will range from 1-19. To use the same boards next game, simply answer “Yes” to “Use last setup?”
All scoreboards selected will now be on the same radio frequency, allowing all boards to be controlled by a
single console. It is extremely important to properly select the proper scoreboard - if more than one
consoles are attempting to connect to the same board, the signals will interfere with each other.
ADDITIONAL RADIO ID INFORMATION:
EXAMPLE: The following boards were turned on in preperation of a basketball game. When “No” was
answered for “Use last setup?” the following was displayed on your 8000 scoreboards.
7

Advanced ID Changing Scenarios (Radio Units Only)
In most cases, IDs can be set by following the methods described in Changing the Scoreboard ID. The follow-
ing text describes some methods to change an individual scoreboard ID in circumstances where multiple
scoreboards are hooked up to the same circuit breaker.
Changing an ID to an Individual Board while while Multiple Scoreboards are On
-Using multiple Consoles (easy method).
Once a scoreboard is connected to a console and a sport, the ID cannot be changed until radio connection is
reset. The radio is connected until 30 seconds after the console connected to it is turned off. If the scoreboard
displays only time of day or blanks (time of day is turned off by setting the time to “0000” in setup), then no
radio connection is established and a scoreboard is ready to be linked.
1. Turn on circuit breaker to scoreboards.
2. Power up one console and select all the boards except for the one that requires an ID change. Select a sport
and ensure that all the scoreboards selected are properly functioning.
3. Power up a second console and follow directions for changing IDs (steps 2-6)
If more than 1 scoreboard is selected, the ID numbers will be the same. Scoreboards that have the same ID number
can ONLY be run in dual mode!
-Using 1 Console (difficult method).
Once a scoreboard is connected to a console and a sport, the ID cannot be changed until radio connection is
reset. The radio is connected until 30 seconds after the console connected to it is turned off. If the scoreboard
displays only time of day or blanks (time of day is turned off by setting the time to “0000” in setup), then no
radio connection is established and a scoreboard is ready to be linked.
Because of this 30 second delay from the time the console is turned off, there is a short window of time to set
or change IDs to boards not currently selected.
1. Turn on circuit breaker to scoreboards.
2. Power up the console and select all the boards except for the one that requires an ID change. Select a sport
and ensure that all the scoreboards selected are properly functioning.
3. Turn off the console.
4. Turn on the console and quickly follow directions for changing IDs (steps 2-6). IDs must be set before the 30
seconds expire and the previously selected boards go to time of day or blank. The newly ID’d boards will go
through the startup cycle.
If more than 1 scoreboard is selected, the ID numbers will be the same when changed. Scoreboards that have the
same ID number can ONLY be run in dual mode! If all boards are set to the same ID, there is no way to change ID
numbers without disconnecting power to individual boards.
Advanced Scoreboard Type Settings (Radio and Hardwire Scoreboards)
If all boards that are selected are the same scoreboard type, it is possible to set the scoreboard type for the
entire group. Scoreboard type can be set without changing the ID by simply pressing enter rather than an ID
number (See Steps 1-7 in Changing Scoreboard ID). If the scoreboard is working properly, AAS recommends
leaving the scoreboard type unchanged by simply pressing enter instead of the 3 digit scoreboard type.
8

Scoreboard Type and Additional ID Information
In previous versions of All American Scoreboards, driver boards were needed to sort through the information
from the the console and direct it to the proper digits on the scoreboard. This system worked well, but each
driver board required a different program chip that would interpret the same information differently.
We’ve simplified the process and standardized each board. Inside each All American Scoreboard is a single
controller plate that holds the receiver board (gets the data sent from the console), a controller/decoder
board (splits the information from the receiver board and sends to digits), and an indicator driver board
(distributes data and power to boards that use indicators). The same program chip can be used for our entire
line of scoreboards.
Although the insides of each scoreboard is made from identical parts (with the exception of boards that do
not use indicators), the information displayed is unique from board to board. Before using an All American
Scoreboard correctly, each scoreboard must be told what kind of scoreboard it is.
Scoreboards are separated into classes, or types. Classes do not neccessarily refer to a sport, but rather how
the information is displayed (usually by digits or indicators).
Before leaving the All American Scoreboard Facility, each scoreboard is properly set to the right scoreboard
type and given an ID number. ID numbers can easlity be changed (see previous page), but should only be
changed in special circumstances. Changing the IDs will likely result in the console and scoreboard changing
to a different radio frequency after being selected, which could be a solution if the facility is having interfer-
ence on a certain channel. If running in dual mode, the scoreboards and console will switch to a channel
determined by the lowest ID number - if interference is occuring after scoreboard selection, try changing the
lowest ID number. After changing the scoreboard ID, the scoreboard type can be changed.
Possible reasons for changing the scoreboard type:
- Scoreboard type was accidentally changed. Prevent this by changing the password. Password must be 5 digit
number.
- A new program chip or receiver board was installed.
To change scoreboard type, select 6 after entering password (see previous page). If not changing ID, press
enter. If changing IDs, wait for scoreboard to reboot. When screen displays “Set Scoreboard Type”, enter the
appropriate 3 digit scoreboard type (displayed below). If scoreboard is not in the list below, refer to our web-
site or call 1(800) 356-8146.
Type 100 (Accessory)
8298, 8299,8497,8499
Type 400 (Standard) *DEFAULT
8003, 8203, 8206, 8208, 8209, 8212, 8214,
8218, 8318, 8321, 8414, 8418, 8420, 8424,
8430, 8433, 8436, 8440, 8450, 8718, 8780, 8804
Type 600 (Deluxe)
8339
Type 300 (Basic)
8347 , 8357, 8369, 8389, 8444, 8454, 8468,
8742, 8782
Type 500 (Extended)
8300, 8302, 8325, 8333, 8327, 8335, 8500,
8502, 8509, 8514, 8518, 8529, 8549, 8599,
8606, 8609, 8614
Type 700 - 8600 Type 800 - 8200, 8201
9

1. Turn on scoreboard.
2. Turn on Console. Press and hold until LCD and LEDs light.
3. Press 1 to select Scoreboard. Use the arrow keys to view more options.
SCOREBOARD CONTROL
MP8000 V.2.**.* 2008
1. SCOREBOARD
2. STAT PANEL ->
4. For the initial use, press Yes/No to change the answer to no. This will walk you through the set-
up process. Failure to do this will cause the default answers to be chosen that were used during the testing process
at the All American Scoreboards facility. Defaults may be changed at any time by going into the setup mode when
game time is stopped. RADIO CONSOLES, PLEASE SEE PREVIOUS SECTION “SCOREBOARD IDENTIFICATION”
Use Last setup?_Yes
RACE 1 Board
Use Last setup?_No
RACE 1 Board
After initial use, press Enter to accept the answer. This answer will bypass setup and take you straight
into game mode with all of your defaults set - skip to Gameplay instructions. Defaults may be changed at any time
by going into the setup mode when game time is stopped.
Sport: ( for more)
1-RACE 2-Bask 3-Bsbl
5. Press 1 to select Racing. (note: if Racing was not the last sport chosen, racing will be another number.
Use arrow keys and choose the number for “RACE”.)
Change Game Setup?
_No
Change Game Setup?
_Yes
6. Select Yes to go into setup. Tip: Use arrow keys to go back to previous questions.
Min = 1, Max = 8
SET: Brightness _
7. Enter the desired brightness and press Enter. Example: . Brightness determines the brightness
of the LEDs on the scoreboard. Brightness levels will vary greatly depending on situation and facility. Typically, a
night game will require a lower brightness level. A day game in bright sunlight will require a higher brightness
level. An game taking place during sunset may require the brightness to change from a max level to a lower level.
Time of Day =_
8. Enter the time of day. Example: for 10:30. The time of day will be displayed on the
scoreboard approximately 40 seconds after power is turned o on the console. Time of Day is stored in the score-
board and will remain in the scoreboard memory for up to 30 days without power. If you wish to leave on the
power to the scoreboard without showing time of day, set the time of day to 00:00. Press enter to leave time of
day unchanged on the scoreboard.
10
SETUP

11
Set as new defaults?
_No
Set as new defaults?
_Yes
16. Press to toggle between Yes and No. To save the settings as defaults, select Yes, then Enter. Settings
chosen will be saved. If the console is being used for similar events with the same scoreboard and sport, Setup can be
bypassed. Defaults may be changed at any time by going into the setup mode when game time is stopped.
Pressing at any time in Setup will exit to game mode. All selections made prior to pressing clear will be stored,
however defaults will not be saved or changed.
Resetting a Game:
When clock is stopped, press twice.
Press to change prompt to YES, then .
NEW GAME? _YES

Startup Display
When the scoreboard is initially turned on, All LEDs will run through a series of brightness levels and self tests.
When a sport is selected, your scoreboard should reect what the console screen displays after setup.
Timer
Press this key to start and stop the Timer. Note: Some keys will not respond when the timer is running.
When clock is stopped press this to reverse direction (count down or count up). An up arrow will
appear on the LCD display to the left of the clock when clock is counting up.
To edit the timer, press this key followed by the correct time to be displayed, then enter.
Press or to leave the time unchanged.
Press Split Time to show the time of a lap temporarily while the timer continues to run in the
background. Press again to show timer.
Both the running timer and the Split Time will be displayed on the console.
Press this to edit the current lap displayed. If laps are counting down, press this button and set the
total number of laps prior to a race.
Example: for 500 laps.
Positions
The console can keep track of up to 10 car numbers at a time. Each position has a seperate column on the console
slipsheet with the following keys:
Press the EDIT key to edit the car displayed for the position.
Example: Car number in Position 2 is 88. Press .
Note: numbers can be 1 or 2 digits and can range from 00-09 and 0-99. Car 01 is dierent than Car 1.
Press the SCRATCH key to delete the car number (car is totaled, etc). The console will ask to conrm.
After conrmation, the number will be deleted and all cars behind in position will move up.
Press the ADVANCE key to advance a car up one position.
Example: Car number in Position 2 is 88. Car number 12 is in position 3. If car 12 passes car 88, press in
column 3. Positions 2 and 3 will ip positions.
Laps
Press this key to increase the lap counter by 1.
Press this key to decrease the lap counter by 1.
Racing
12
ID will show in timer or in
rst position on boards
without a timer.

WARNING! OPERATION OF THE UNIT WITH THE ELECTRICAL EXPOSED IS
DANGEROUS. BE SURE ALL TOOLS AND ANY OTHER MATERIALS ARE REMOVED
FROM THE UNIT, AND ALL ACCESS COVERS ARE REPLACED AND CLOSED BEFORE
POWER IS TURNED ON.
NOTE: For Advanced Trouble Shooting, Service Manuals and Replacement Part Information
go to www.allamericanscoreboards.
3.0 Safety Information
The owner of the All American Scoreboard (AAS) is responsible for safe operation and repair.
He therefore is obliged to familiarize operating personnel with the contents of this manual
and make them aware of all possible hazards.
NOTE: When using this equipment, always follow the manufacturer’s instructions for
safe operation. In case of emergency, please telephone Technical Support or a qualied
service technician.
Do not operate the sign until it is completely assembled and installed per the instructions
supplied by AAS.
AAS recommends that your main power be installed by a licensed electrician in accordance
with the local building and electrical codes.
All equipment must be grounded in accordance with the local building and electrical codes.
AAS recommends Earth Link Ground.
If any part of the Scoreboard equipment is malfunctioning or has been damaged, cease
operation and consult with AAS Technical Support or qualied service technician before
further use.
Use only AAS specied or recommended replacements parts.
WARNING! USE A LOCK OUT/TAG OUT ON CIRCUIT BREAKERS OR “POWER
ON/OFF” SWITCHES WHEN PERFORMING INSTALLATION, REPAIRS OR
MAINTENANCE.
When performing repairs be mindful of the weather and work area conditions. Avoid the
unit’s exposure to the elements, water and debris, or anything that may be dangerous or
cause damage to the equipment.
WARNING! OPERATION OF THE UNIT WITH THE ELECTRICAL CIRCUITRY
EXPOSED IS DANGEROUS. BE SURE ALL TOOLS AND ANY OTHER MATERIALS
ARE REMOVED FROM THE UNIT, AND ALL ACCESS COVERS ARE REPLACED
AND CLOSED BEFORE POWER IS TURNED ON.
CAUTION: Use of solvent cleaners or a power washer on your Scoreboard may
cause permanent damage.
13

4.0 Warranty
Five Year Limited Warranty
Non-compliance with procedures of Installation, Safety, Operation and/or Maintenance
practices dened in this manual may result in a Warranty issue.
This warranty extends to and is enforceable by only the original consumer purchaser
and only for the period (during the applicable term) which the product remains in the
possession of the original consumer purchaser. “Original consumer purchaser” means the
person who rst purchased the product covered by this warranty other than for purpose
of resale. This warranty does not apply if it is found that at any time the equipment has
not been used for its intended purpose.
NOTE: Please ask your dealer, distributor or sales representative for details.
CAUTION! Any unauthorized changes or modications to this unit without
our prior written approval will void the user’s warranty and will transfer health
and safety obligations to the user
CAUTION! Changes or modications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment
NOTE: This equipment has been tested and found to comply with the limits for a
class “A” Digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with
Owner’s Manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area can cause harmful interference in which case
the user will be required to correct the interference at their expense.
14

© Copyright All American Scoreboards 2008-2009
This is the exclusive property of All American Scoreboards® a division of Everbrite® LLC. Use
of or duplication of this document in any manner without the expressed written consent of
All American Scoreboards® is prohibited.
The information contained in this document is subject to change without notice and should
not be construed as a commitment by All American Scoreboards®.
All American Scoreboards® assumes no responsibility for any errors that may appear in this
document. Nor does it make expressed or implied warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of merchantability and tness
for a particular purpose.
All American Scoreboards® shall not be liable for incidental or consequential damages in
connection with, or arising out of the furnishing, performance, or use of this document and
the program material, which it describes.
Trademarks Credits
All American Scoreboards® is a registered trademark of Everbrite® LLC.
Everbrite® is a registered trademark of AAS LLC.
5.0 Technical Support
5.1 Customer Service
Customer satisfaction is the top priority at AAS. Our skilled, experienced Account Manage-
ment teams are dedicated to providing highly responsive service through all phases of our
client’s programs.
These teams are computer-linked to each of our manufacturing facilities to provide “on-line”
updates on the status of customer orders. Furthermore, AAS’s EDI capabilities allow electronic
interchange to eciently process customer orders.
5.2 Contact Information
All American Scoreboards
401 S. Main Street
Pardeeville, WI 53954
PHONE: [phone]
FAX: [phone]
www.allamericanscoreboards.com
15