REDBACK® DAB+/FM Tuner & CD/MP3 Disc Player
RADIO TUNER SECTION:
Page 6
KEYS EXPLANATION
1-10 Press one of these buttons on the remote control and the tuner will jump to that preset station whose frequency is stored in
memory. Press SHIFT and one of these numerical keys and the tuner will jump to a selected preset station between 11-20.
This is true for both FM and DAB+ stations that have been stored in a preset memory location.
Press and hold one of these numerical keys to write a receiving frequency into one of the M1-M10 preset memory locations.
Press SHIFT first, then press and hold a number key, and this will save a receiving frequency into the M11-M20 preset
memory. This storage method is the same for FM and DAB+ stations. The message on screen is “Preset X saved” where X is
the number.
SHIFT Short press activates SHIFT function (Preset 11-20). A longer press and hold also activates FM scanned list (See below).
FM LIST FM Station scanned list. This shows which FM stations have been saved after an AUTO SCAN. (DAB+ mode is automatically
in a list format for all stations). Use REV-SKIP-CUE to scroll up or down through the stored station frequencies in the list.
Press ENTER to tune to the selected station.
AUTO-SCAN In FM and DAB modes: Press and hold for longer than two seconds to activate full scan mode. This will instruct the receiver
to scan for all available frequencies, FM or DAB+ depending on the mode to which the device is set. The captured stations
will be the strongest frequencies and these will be stored in general memory (i.e. not preset location). Press and hold the
jogwheel as an alternative activation for this Auto-Scan function.
MODE Press this button to switch between FM and DAB+ modes.
MENU FM Mode: Audio Setting or Main Menu – [Time Setup, Sleep, Factory reset, SW Version]
DAB+: DAB Scan or Main Menu –
[Time setup, Sleep, Prune stations, Station order, Factory reset, SW version]
INFO In FM mode, it will change between the different RDS content information options like: Program Type [PTY], Program
Segment [PS], Clock Time [CT], Radio Text [RT], Program ID [PI]. In DAB+ mode it will change between similar data displayed
for that station
ENTER Press this button to select what you desire when navigating menus or to select a station. If you use the jogwheel to tune
DAB+ stations, the station you select will auto tune i.e. no need to press ENTER.
PRESET You can use this button on the remote control to recall or store the favourite stations in the memory locations – 20 for each
mode.
Recall the preset station: Press PRESET first, then use REV / CUE to select one of the 1-20 preset stations, then press
ENTER key to confirm the selection.
Store the station into memory: Press PRESET first, then use REV / CUE to select a memory location (1-20). Press ENTER
and hold for longer than two seconds to store the present station. This is an alternative method to store a station frequency.
The message on screen is “Preset X saved” where X is the number.
SLEEP You can use this button for setting the tuner (FM / DAB+) sleep time. Press SLEEP, then use DOWN or UP to select: SLEEP
OFF, 15, 30, 45, 60, 90. Then press ENTER to confirm the time selection. The unit will play for the set number of minutes
and then switch into standby. This function is alternatively activated from the MENU.
MUTE Press to mute the audio output. Press again to recover the output back to that level.
UP In FM mode: Press once to tune higher frequencies. Press and hold to activate the automatic search to find the next station.
In DAB mode: Press once to tune to the next frequency increment or station name.
DOWN In FM mode: Press once to tune lower frequencies. Press and hold to activate the automatic search to find the next station.
In DAB mode: Press once to tune to the previous frequency decrement or station name.
When navigating menus, press this key to select the left item. This is on the LHS of the ENTER button on the Front Panel.
CD/TUNER Switch between CD and RECEIVER section operation. The corresponding LED will illuminate on the front panel to indicate
which section is operational. Only the remote control has this important button!
