AMCON EQ-6002 User manual

1-800-255-6161• Fax [phone]
www.amconlabs.com
AMCON AUTOMATIC
CHART PROJECTOR
USER’S MANUAL
EQ-6002

Disclaimer............................................................................................................2
1. Introduction......................................................................................................3
2. Safety Instructions.............................................................. ............................3
3. Charts and Specifications........................................... ...................................4
4. Parts of the Instrument................................................................. ..................6
4.1 Projector Parts....................................................................................6
4.2 Remote Control Parts.........................................................................6
5. Operating Procedures ....................................................................................7
5.1 Preparation .........................................................................................7
5.2 Operation of the Remote Control......................................................7
5.3 Using the Program Function............................................ .................8
6. Maintenance and Care.......................................................... ..........................9
6.1 Daily Maintenance..............................................................................9
6.2 Replacing the Bulb.............................................................................9
6.3 Replacing the Fuse. ...........................................................................9
6.4 Changing the Channel Setting of the Remote Control.................. 10
7. Troubleshooting............................................................................................11

Automatic Chart Projector - EQ-6002
________________________________________________________________
2
DISCLAIMER
Amcon, The Eyecare Supply Center makes no representations or warranties,
either expressed or implied, with respect to the contents hereof and specifically
disclaims any warranties, merchantability, or fitness for any particular purpose.
Further, Amcon, The Eyecare Supply Center reserves the right to revise this
publication and to make changes from time to time in the contents hereof without
obligation of this company to notify any person of such revision or changes.

Automatic Chart Projector - EQ-6002
________________________________________________________________
3
1. Introduction
Thank you for purchasing the Amcon Automatic Chart Projector. Please read
this instruction manual and keep it in a convenient location for future reference.
The remote controlled Amcon Automatic Chart Projector is used to test visual
acuity. The Amcon Automatic Chart Projector provides operational convenience
in a high quality instrument.
2. Safety Instructions
To ensure safe usage of this product, it is important that you follow the
instructions in this manual as well as the warning notices on the instrument.
•Do not look directly into the projector lens during operation. The intense
light beam may be harmful to your eyes.
•To avoid damage, always place this device on a stable stand. This
instrument is not designed to sustain rough treatment or falls.
•To reduce the risk of electric shock, do not disassemble this projector.
Take it to a qualified technician when service or repair is required.
Incorrect reassembly can cause malfunction of the projector or electric
shock when the appliance is subsequently used.
•Never attempt to replace the bulb or any electronic component unless the
instrument is unplugged from the power source.
• Always open the lens shutter or remove the lens cap prior to turning on
the projector lamp.
•Avoid placing this projector in the following environments:
oPoorly ventilated or confined locations. Place at least 2 inches (5
cm) from walls and allow free flow of air around the projector.
oLocations where temperatures may become excessively high, over
90°F (32°C).
oLocations with excessive humidity, dust, or cigarette smoke.
•Do not place any objects on projector.
•Avoid placing liquids near the projector. If the projector does become wet,
immediately disconnect it from the power source.

Automatic Chart Projector - EQ-6002
________________________________________________________________
4
3. Charts and Specifications
Letter Charts:
Tumbling E Charts:
Number Charts:
Picture Charts:
Worth Four Dot Chart: Astigmatic Chart:
Red / Green Charts:

Automatic Chart Projector - EQ-6002
________________________________________________________________
5
Binocular Vision Testing Charts:
Refraction distance 5 ft – 20 ft
Projection distance 5 ft – 20 ft
Projection magnification 30X (at 20 ft refraction)
Number of charts 30
Chart changeover 1 frame / 0.3 sec.
Mask changeover 1 frame / 0.1 sec.
Bulb 12V 50W (Halogen)
Replacement bulbs available from Amcon
Product number: RQ-6200
Electricity AC 110V 60Hz
Power consumption 80W
Weight 13 lbs. 3 ounces (6.0 Kg)
Dimensions 11 7/8” x 9” x 9 ½” (30 cm X 23 cm X 24 cm)

Automatic Chart Projector - EQ-6002
________________________________________________________________
6
4. Parts of the Instrument
4.1 Projector Parts
1) Top Cover
2) Remote Sensor
3) Front Panel
4) Lamp Cover
5) Barrel Screw
6) Projection Window
7) Base
8) Power Switch
9) Power Socket
4.2 Remote Control Parts
1) Remote Signal Emitter
2) Chart Switches
3) Light Switch
4) Reset Switch
5) Program Forward Switch
6) Program Back Switch
7) Highlight Selectors
8) Highlight Transfer Selectors
9) R/G switch
10) Program switch
1
2
3
4
5
6
7
8
9
10

Automatic Chart Projector - EQ-6002
________________________________________________________________
7
5. Operating Procedures
Caution: Do not tilt the projector or place in an unstable place. The projector
may topple over, drop or cause injury.
Warning: Connect the power plug to a properly grounded three-prong AC outlet.
If it is connected to an ungrounded outlet, fire and/or electrical shock may result.
Caution: Handling the power plug with wet hands can cause electric shock.
5.1 Preparation
Place the instrument approximately level to the person to be tested. Turn the
power switch ‘off’. Insert the power cord into the power socket on the projector
body and plug into the wall outlet. Turn the power switch ‘on’. Remove the
battery cover from the back of the remote controller. Insert batteries into the
remote controller as illustrated and replace the battery cover. Adjust the position
of the projector so that the projector light is centered on the screen. Be sure the
projector is in the position from which it will be used. To focus the projector, slide
the focusing knob that is found on the underside of the projector base (on the
same side as the lamp cover). There is a barrel screw that must be loosened
before the knob can be moved. The enclosed Allen wrench can be used to
loosen or tighten this screw.
5.2 Operation of the Remote Control
Turn the projector’s power switch on. The chart will automatically reset to the
start position and the lamp will light. When using the remote controller, point the
remote signal emitter in the direction of the remote sensor on the front of the
projector. The switch functions are as follows:
a) Chart Switches - Projects the indicated chart on the switch
b) Light Switch - Turns the lamp off and on
c) Reset Switch - Returns to chart 1 of the program
d) Program Forward Switch - Fowards the program automatically
e) Program Back Switch - Reverses the program automatically
f) Highlight Selector - Isolates chart characters
g) Highlight Transfer Selectors - Moves the isolation of the characters in
the direction indicated. (When the highlighted area of a chart being
projected advances to the maximum or minimum on that chart, the
next or previous chart in the sequence will automatically appear.
Charts can be switched within the same type.)
h) R&G Switch - Applies the R&G filters to the designated charts
i) Program Switch - Refer to the Program Procedure, section 5.3, for
using this function
Note: The projector will automatically turn off if not in use for 5 minutes.

Automatic Chart Projector - EQ-6002
________________________________________________________________
8
5.3 Using the Program Function
Accessing the Programming Mode
a) Turn on the power switch. The projector goes into initialization state.
b) Press the “RESET” button on the remote control.
c) Press the “R and G filter” button on the remote control.
d) Press the “Reset” button again on the remote control. The projector
will beep twice after pressing each button in “1b, 1c, 1d”. After the
third button, the projector will be in programming mode. At any time
up to step “d”, pressing any other button will return the projector to
normal operating state.
Select Program 1 or 2
Press the “P1/P2” switch to select program 1 or 2. The beeper will sound
once if program 1 is selected and twice if program 2 is selected.
Selecting Charts for the Program
a) Press the “program up” button to open the position for the first chart.
b) Select the desired chart button along with the desired “highlight”
button.
c) Press the “program up” button again to enter the selection and move
to open the next position of the program. The beeper will sound four
times. Repeat steps 3a, 3b, 3c to enter other charts. Up to 30
selections are possible.
Completing the Program
a) When finished entering, press the “Reset” button to exit.
b) Press the light switch to turn off the projector.
Using the Program
a) To use a program, select program P1 or P2 by pressing the “P1/P2”
button. The beeper will indicate the program selected by sounding
once for P1 and twice for P2.
b) Press the “Program Up” button to run the program. The “Program Up”
and “Program Down” buttons will advance or reverse the program.

Automatic Chart Projector - EQ-6002
________________________________________________________________
9
6. Maintenance and Care
6.1 Daily Maintenance
•Cover the projector when not in use. This instrument is sensitive to dust
contamination.
•Turn the power switch off when not in use. It is also recommended to
unplug this instrument when not in use for longer periods of time.
•Keep projector clean by wiping the outside panels with a dry cloth. To
remove more difficult stains, a damp cloth with a mild detergent may be
used. A mild glass cleaner may be used on the outside panels. Be
careful not to dampen the inside parts of the projector.
• When the lens is dirty, wipe it lightly with a good quality, dry microfiber
cloth. An Amcon Vista Cham is recommended.
6.2 Replacing the Bulb
Caution: To avoid electric shock, unplug the power cable when replacing the
projection lamp.
Caution: Do not replace the projection lamp immediately after turning off the
light. The lamp may still be hot and could lead to burns.
Turn the power switch off. Remove the lamp cover screw and remove the cover.
Remove the lamp attaching screw, hold the socket and remove the lamp. Hold
the socket and the lamp flange and remove the lamp from the socket. Install the
new lamp securely. Make sure you install it in the correct direction. Do not touch
the glass of the bulb directly with your fingers. If the bulb is touched by accident,
wipe the fingerprint off with alcohol. Replacement bulbs are available from
Amcon Product number: RQ-6200. Match the protruded part of the lamp
attaching area with the lamp flange notch and tighten with the lamp attaching
screw to secure the lamp. Place the lamp cover on. Turn the power switch on.
Make a trial projection to check that there is no illumination irregularity. If there is
any irregularity, turn the power off again and check that the lamp is properly
installed.
6.3 Replacing the Fuse
Warning: Unplug the power cable before removing the fuse cover to replace the
fuse. Removing the fuse cover with the power cable plugged in can cause
electric shock.
Warning: Use only attaching fuses (250 v, 1A). Using other fuses may cause a
fire in the event that the instrument fails.

Automatic Chart Projector - EQ-6002
________________________________________________________________
10
Turn the power switch off and disconnect the power supply plug. The fuse holder
is located just below the power supply socket. Pull on the fuse holder to remove
it. The fuse will be removed together with the holder. Remove the blown fuses
and insert the new fuses on the cap of the fuse holder and install it as before.
6.4 Changing the Channel Setting of the Remote Control
Turn the power switch off and unplug the power cable. Remove the lamp cover
screws and the screw on the lower cover (four in total) and lift the top to remove
it. Change the DIP switch 5 and 6 according to the diagram. Remove the battery
cover from the back of the remote controller and change the channel switch S.
Replace the top cover after completing the DIP switch setting, tighten the screws
on the lower cover and then tighten the lamp cover with attaching screw.

Automatic Chart Projector - EQ-6002
________________________________________________________________
11
7. Troubleshooting
Warning: Do not break down, modify or repair the equipment. Doing so can
cause electric shock. Request a repair from your dealer. Check the situations
covered in the following table for the problem you are experiencing. If your
situation is not covered or if the recommended action does not solve the
problem, contact your dealer for further support.