AnthroDesk D2 User manual

D2 ASSEMBLY INSTRUCTIONS
for future use Instructions must be followed
NOTICE These instructions must be saved
1-9

NO. 1
1 1 1
2
2 2
3 4
21
2
4
5
3
3
CHECK LIST
mm
B (8pcs)
M8x20mm
E
D (2pcs)
ST3.5x16mm
C (12pcs)
ST5.0x23mm
（optional）
2-9
QTY.
5
A (4pcs)
M6x12
M5

3 - 9
2
1
1
2
BE CAREFUL WITH THE CABLE!!!

4 - 9
2
12mm
E
M5
3
A
12mm
E
M5
4
E
A
E
A
M6x
1
A (2pcs)
A (2pcs)
M6x

5 - 9
1
33
B (8pcs)
M8x20mm
B
BB
B
B
BB
B
E
M5
5
E
M5
6
TIGHTEN THE SCREWS
E

6 - 9
1
E
M5
7
8
E
LOOSEN

7 - 9
4
4
D (2pcs)
ST3.5x16mm
DD
DD
C (12pcs)
ST5.0x23mm（optional）
C
C
C
C
C
C C
C C
C C
C
9
D
D
LEFT OR RIGHT
OR
10

8 - 9
5
5
11 E
M5
E
TIGHTEN
12
PLUG IN

9 - 9
Up & Down key Display Screen
Memory Key HOME Key
UP & DOWN Keys
Please keep touching UP/DOWN key to adjust desk height until you get an optimum height.
Display Screen
Displays the height value of the desk.
Handset shows error code and solution
Sensitivity of anti collision
A
detection system (lowering)
most sensitivity
1
general sensitivity
2
less sensitivity
3
4anti collision OFF
most sensitivity
1
general sensitivity
2
less sensitivity
3
4anti collision OFF
Press M2 to go back to settings,
and again to go back to normal
b
Cm or inch setting
cm
1
inch
2
Sensitivity of anti collision
CUsing ︿ or ﹀ key to set basic height
Basic height setting
F
detection system (raising)
dUsing ︿ or ﹀ to adjust the height
Minimum height setting
EUsing ︿ or ﹀ to adjust the height
Maximum height setting
Press the 'Home' key untill
you hear a second 'beep'
sound.
use︿or﹀key to choose
A,B,C,D,E,F.
︿
﹀
︿
﹀
︿
﹀
︿
Press
﹀
Home key
Press
Home key
Press
Home key
Press
Home key
Press
Home key
Press
Home key
Additional Desk Settings
Safety Function
The desk has a built-in collision detection feature and will stop raising/lowering if unexpected resistance is detected.
ER1
ER2
ER3
ER4
ER5
Error code Fault cause Solution
Motor stop
Synchro error beyond 15mm
Cable fault
Communication fault
Overload protection
Power off and restart. If fault still exists, it is a motor problem.
Power off and restart. If handset displays RST (DOWN key unlocked), keep touching the
DOWN key until the lowest height is reached.
Check motor cable for breaks.If none, re-connect and power off and restart.
Check cables to ensure handset and controller are properly connected. Power off and restart.
Error message will appear when load>180kg. Reduce load, then power off and restart.
Hot
Run continuously for
2.5 to 5 minutes. Overload, protection will automatically stop desk. Desk will operate again after 5 minutes.
The handset is touch sensitive and will enter 'sleep' mode after 30 seconds of inactivity.
Touching any of the keys will activate the handset.
Memory Key （M1/M2）
After seting memory keys, the desk can lift automatically to memory height.
How to set memory mode
Press the M1/M2 key for 5 seconds. The desk will 'beep' to indicate that the current height has been saved
into memory. Lightly touch the M1/M2 key and the desk will moved to the set height automatically.
HOME Key
Lightly touch the Home key to move the desk to the most common sitting height of 72cm.
operational mode.