Apollo Pro Dunk User manual

1
OWNER’S
MANUAL
Warning
 ! Do not slide, climb, or
play on pole.
 ! Keep organic material
away from pole base.
Grass, litter, etc. could
cause corrosion and /or
deterioration.
 ! Check pole system
twice a year for signs of
corrosion (rust, pitting,
and chipping). Remove
rust and/or loose paint
completely and repaint
with exterior enamel
paint. If rust has pene-
trated through the steel
anywhere, replace pole
immediately.
 ! Check unit before
each use for loose
hardware, excessive
wear, and signs of cor-
rosion and repair be-
fore using.
 ! During play, use ex-
treme caution to keep
players face away from
the backboard, rim, and
net.
 ! Wear a mouth guard
when playing to avoid
dental injuries.
 ! When adjusting
height, keep hands and
fingers away from mov-
ing parts.
 ! During play, do not
wear jewelry (rings,
watches, necklaces,
etc.). Objects may en-
tangle in net.
Pro Dunk®
Basketball System
WELCOME TO THE FAMILY OF
PRO DUNK® OWNERS
Thank you for purchasing our basketball system. We try hard to ensure that our
products are of high quality and free of manufacturing defects and of missing
parts. However, if you have any problems with your basketball pole, such as a
manufacturing defect or a missing part please contact us at the following:
Toll Free: 1.888.600.8545 Pro Dunk®
Web: www.produnk.com 22047 Lutheran Church Rd.
Tomball, TX 77377
Please provide model number, serial number, and/or part number of the product
and/or part when you call, write or email. These numbers can be found on the
product, packaging, or on the back of the main pole.
Purchase Parts: www.produnk.com/parts
Support: www.produnk.com/support
Read this manual all the way through before starting to
put up your system. Then read each step completely
before beginning installation.
www.Call811.com

2
Bill Of Materials
No. Description Qty.
1 Bottom Post 1
2 Top Post 1
3 Upper Board Arm 2
4 Lower Board Arm 1
5 Backboard 1
6 Rim 1
7 Rim Cover Plate 1
8 Post Ear 2
9 Actuator 1
10 Anchor Template (Needed 1st Day) 1
11 Backboard Pad Right 1
12 Backboard Pad Left 1
13 Pole Pad 1
14 Actuator Handle 1
15 Rebar (Needed 1st Day) 4
16 "J" Bolt (Anchor Bolt) (Needed 1st Day) 4
17 12mm x 40mm Bolt 1
18 10mm x 175mm Bolt 3
19 10mm x 165mm Bolt 1
20 10mm x 120mm Carriage Bolt 4
21 10mm x 70mm Bolt 4
22 10mm x 60mm Bolt 4
23 6mm x 40mm Bolt 6
24 5mm x 15mm Bolt 4
25 12mm Nylon Locknut 1
26 10mm Nylon Locknut 12
27 16mm Nylon Locknut (Needed 1st Day) 8
28 10mm Hex Nut 4
29 16mm Washer 8
30 12mm Washer 2
31 10mm Washer 26
32 6mm Washer 12
33 5mm Washer 4
34 10mm Lock Washer 4
35 5mm Lock Washer 4
36 Plastic and Steel Rim Spacer 4
37 16mm Plastic Protective Sleeve 4
38 25mm Plastic Stop Spacer 2
39 10mm Plastic Washer 8
40 12mm Plastic Washer 2
41 16mm Nylon Locknut 4
42 6mm Locknut 6

3
Assembled Diagram—Use as reference

4
Safety Instructions
 All tools used to assemble this product
should be used in compliance with manu-
facturer’s guidelines.
 Installation of this product will require
heavy lifting and bending. Any person that
is not capable of such activity should not
participate in the installation of this product.
 If using a ladder during assemble, use ex-
treme caution and refer to the warnings
and cautions on the ladder.
 Due to the size and weight of this product,
we recommend at least (4) competent
adults are present.
 Before digging the hole for the anchor sys-
tem, please call 811 to ensure that all un-
derground utilities are a safe distance
away from the anchor system.
 Make sure there are no overhead power
lines within a 25 foot radius of the basket-
ball system.
 All parts and components necessary to
complete proper installation are included
within this product. Do not use parts not
included with our system. Failure to follow
this requirement could cause product mal-
function and will void warranty of this prod-
uct.
 Keep all organic materials away from parts
and components to avoid corrosion.
 Do not dunk or hang on the rim.
 Do not climb on any part of the basketball
system as it was not intended for this activ-
ity.
IMPORTANT
It is the responsibility of purchaser to ensure that
all installers and players fully comply with the de-
tailed instructions set forth in this product installa-
tion manual. Product assembly should be carried
out exactly as instructed and owner supervision
of use and installation is required to prevent risk
of product malfunction or risk injury.
Pro Dunk® retains the right to modify this
document at any time without notice or
obligation.
Keep this installation manual as a refer-
ence for your safety and the safety of
those playing on the basketball system.
Additional copies of these safety instruc-
tions are available by calling customer
service at 1.888.600.8545 or at
www.produnk.com
 Do not use the basketball system as a lift or to
hoist anything.
 Players should wear protective mouth guard
during play to avoid any time of dental injury.
 Players should refrain from wearing any jew-
elry that could potentially get caught in the rim
or net.
 Do not allow children to adjust basketball sys-
tem.
 Check the basketball system on a regular ba-
sis to ensure that there are no signs of dete-
rioration or corrosion, loose hardware, or
damaged parts. If you see any signs of dam-
age perform maintenance or contact Pro
Dunk® for replacement.
 For maintenance repairs please contact a pro-
fessional.
 Failure to follow these safety instructions
could result in product malfunction, seri-
ous injury, or even death.

5
Installation Overview
In order to have the safest, fun and longest use of your APOLLO™system,
please note and heed the following:
1) Prior to goal assembly, call utility services (811) for location of un-
derground utility lines before you dig.
2) Immediately unpack all components and cross check against bill
of materials. Report any shortages to Pro Dunk® customer ser-
vice at 1.888.600.8545.
3) Parts can be ordered at www.produnk.com
4) Assembly is a two part process.
PART 1 PART 2
Day 1. Complete Anchor System Installa-
tion Instructions. (Below)
Day 5. Complete APOLLO™assem-
bly instructions.
Day 2. Allow concrete to cure.
Day 3 Allow concrete to cure.
Day 4. Allow concrete to cure.
5) For safety measures, have at least 4 capable persons to assist
you in assembly of your APOLLO™Goal.
White—Proposed Excavation
Pink—Temporary Survey Markings
Red—Electric Power Lines, Cables, Conduit, and Lighting Cables
Yellow—Gas, Oil, Petroleum, or Gaseous Materials
Orange—Communication, Alarm or Signal Lines, Cables or Conduit
Blue—Portable Water
Purple—Reclaimed Water, Irrigation and Slurry Lines
Green—Sewers and Drain Lines
www.Call811.com

6
Required Tools
 Post Hole Digger
 Shovel
 Wheel Barrow
 (9) 80 lbs. bags of concrete OR
(12) 60 lbs. bags of concrete
 Trowel
 Level
 Tape Measure
 Box Cutter
 (2) Crescent Wrenches
 (2) Padded Saw Horses
 Phillips Screw Driver
 Ladder
 Block Of Wood
 Optional Wood Form
 24mm
 18mm
 17mm
Socket/Wrench Sizes
Recommended
Court Layout Diagram

7
Accessories
https://www.produnk.com/basketball_goals/accessories
Catch run away balls from going behind your basketball goal
with the Pro Dunk Backstop Net. A custom fitted 10.5 feet
wide by 7.5 feet tall durable outdoor net stops and rebounds
balls back into your driveway.
Comes with Free Shipping!
Goal Light LED!
produnk.com/video/goal_light_led.html
Backstop Net
produnk.com/video/backstop_net.html
Court Marking Stencil
produnk.com/video/court_marking_stencil_kit.html
Why stop playing in the evening. You don’t have to! Order the
Pro Dunk Goal Light LED. It easily lights up the entire 3-point
line with 2 powerful LED lamps extending play into the night.
There’s always time for one more game!
[patent pending 62458721]
Comes with Free Shipping!
Customize your pole padding with anything you can think of in-
cluding family, NBA, college, high school, church or school
names. Made of high quality outdoor 3M vinyl. Solid white char-
acters are pre-spaced on transfer paper for easy application to
your pole padding.
Comes with Free Shipping!
Haven’t you always wanted your playing area to have regulation
striping like a real basketball court. Well now you can with the
Court Marking Stencil Kit. Just lay it out on your court and ap-
plied the included white paint. Includes the key with side
markings, freethow, and the entire 3-point line. Fully reus-
able and a great family DIY project.
Comes with Free Shipping!
Custom Pole Pad Lettering
produnk.com/video/pole_pad_lettering.html

8
Day 1
ANCHOR SYSTEM INSTALLATION INSTRUCTIONS
1) Installation Location
Choose the proper location to dig for the concrete footing. Use the distance chart
on the pervious page to help you make your decision. When choosing the exact
position to dig, make sure to maximize the amount of playing surface while mini-
mizing possible driveway obstruction.
2) Digging Pier Hole
Dig hole 36" deep and 16"
square. Be sure to bell out the
bottom of the hole 20” to give
added stability to the footing.
NOTE: If you live in an area
where the frost line is below
36" it is advisable to dig to
normal frost line.
NOTE: Your steel plate must
be as has or higher than the
playing area to ensure the
system will adjust to 10ft.

9
3) Anchor Assembly
Twist (4) nuts (#27) to the bottom of threads
on (4) J-bolts (#16). Place these J-bolts
through the holes on the black anchor plate
(#10) and install (4) nuts (#27) and tighten.
The bottom of the J-bolts should be positioned
as shown.
NOTE: There will be (8) flat washers
(#29) and (4) lock hex nuts (#41) left over
after the Anchor Assembly. These will be
used on the Assembly Day. You can set
them to the side for now.
Determine the location of the anchor system. Use the
following dimensions as a guide.
The system requires a minimum of 16 inches behind
the main post to allow for adjustment.
Overhang is defined as the distance between the front
of the backboard to the front of the main post when
the system is at 10ft. The overhang on the APOLLO
is 2.5ft.
4) Pouring Concrete and Setting Pier Kit
NOTE: Make certain that you have enough concrete to
finish the job. Allowing a portion to dry while you pur-
chase more concrete will weaken the footing.
Mix (9) 80 lbs. bags of concrete in wheel barrow or cement mixer and pour in pre-dug
hole about half full. Agitate concrete with shovel or broomstick to ensure proper fill.
Place (4) Pieces of rebar (#15) (included) in the middle of the hole about 8 inches
apart to create a square in the middle of the hole. All 4 pieces of rebar need to over-
lap the J-bolts at least 6 inches.
NOTE: Mix concrete to manufacture specifications.
NOTE: The bottom 4 nuts will be forever embedded in
concrete. The top 4 nuts remain on bolts and are used
for leveling.

10
Use the level to ensure that the anchor template (#10) it is level in all directions. Ad-
ditionally, the center line of the Anchor J-Bolts (#16) must be parallel with the edge of
the playing surface.
Pour the remaining concrete into the hole until completely full and coming out of the
top. Using a trowel, smooth the concrete to your preferred liking.
Place the assembled anchor system in hole to the point where the bottom of the black
anchor plate (#10) is flush with the top of the finished concrete.
Once completely smooth let the concrete cure. This can take up to a week. Consult
the instructions on the concrete bag for curing times and directions.
Day 1 Complete!
NOTE: The top of the concrete needs to be level with
or higher than your playing area to ensure you sys-
tem will adjust to 10ft regulation height.

11
Day ~5
APOLLO™ASSEMBLY INSTRUCTIONS
IMPORTANT! Nylon washers adequately space
painted parts at all pivot points. Neglecting the use
of these washers will result in rusted parts.
NOTE: All board arms are made of rectangular tub-
ing. Tightening hardware too tight may damage
tubing and make adjustment of system difficult.
5) Connecting Top and Bottom Posts
Before putting any of the poles tubes together,
mark bottom pole (#1) 6 inches from the top end.
Be sure to match up both “Back Side” stickers
on the back of the poles.
6) Connecting Top and Bottom Posts
Align the upper pole (#2) with the bottom pole (#1)
as shown and slide them together. Stand poles up
on a block of wood, lift poles up and hit on a block
of wood until the bottom of the upper pole reaches
the 6” mark on the bottom pole. Hit poles together
a minimum of 7 times. This is a friction-locking
joint and requires no hardware.
IMPORTANT! DO NOT hit poles with hammer or
sledge hammer to slide poles together.
7) Attach Post Ears
Attach Post Ears (#8) to holes near the bottom of
Top Post (#2) using four bolts (#20) four washers
(#31) and four hex nuts (#26).

12
8) Actuator Assembly
Lay Pole Assembly on its side on two padded saw
horses. Slide tab on Actuator (#9) between Post Ears (#8)
and secure using one bolt (#17), two washers (#30), two
plastic washers (#40) and one lock nut (#25). Tighten
bolts tight.
9) Safety Stop Assembly
Secure two stop spacers (#38) to pole using one hex bolt
(#19) and one lock nut (#26).
10) Extension Arm Assembly
Attach lower arms (#4) to Top Pole (#2), using a hex bolt
(#18), two flat washers (#31), two plastic washers (#39)
and lock nut (#26).
Note: make sure lettering is right side up.
DO NOT tighten bolt (#18) at this time.

13
11) Assemble Actuator to Post
Secure Actuator (#9) to Lower Arms (#4) using one bolt
(#18), two flat washers (#31), and one lock nut (#26).
Tighten both bolts (#18) securing Lower Arm (#4).
Note: Tighten bolts snug but, do not over tighten.
Board Arms must pivot freely.
12) Assemble Upper Arms
Attach Upper Arms (#3) to Top Pole (#2), us-
ing a bolt (#18), two flat washers (#31), two
plastic washers (#39) and one lock nut
(#26).
Note: Tighten bolts snug but, do not over
tighten. Board Arms must pivot freely.
13) Mount Pole
Locate hardware needed to mount pole to anchor bolts. You
will need, eight flat washers (#29), four locking hex nuts (#41)
and four thread protectors (#37).
Note: Do not remove the nuts you installed in step 3.
Put a flat washer (#29) on each anchor bolt. Lift post onto an-
chor system and secure with one flatwasher (#29), and one
locking hex nut (#41) for each anchor bolt. Tighten Fasteners
finger tight, leave loose enough to level pole. Place a level on
pole and adjust bottom nuts (#27) until pole is level. Tighten
top four hex nuts (#41) tight. Place a thread protector (#37) on
each anchor bolt.

14
14) Actuator Crank Assembly
Slide Actuator Crank (#14) onto shaft on
the bottom of Actuator (#9). Line up hole in
shaft with hole in Actuator Crank and insert
Pin to secure.
To aid in the assembly of the backboard,
lower the backboard, by turning the Actua-
tor Crank, until the lower arm makes con-
tact with Stop Spacer (#38).
15) Backboard Assembly
With at least three capable peo-
ple, raise the backboard assem-
bly up and have the fourth attach
Lower Board Arms to lower
mounting tubes on backboard
using two bolts (#21), two plastic
washers (#39), four washers
(#31) and two lock nuts (#26).
NOTE: DO NOT over tighten
these bolts. This is a pivot
point. Snug is tight enough.
Attach Upper Board Arms to up-
per mounting tubes on back-
board using two bolts (#21), two
plastic washers (#39), four wash-
ers (#31) and two lock nuts
(#26).
NOTE: DO NOT over tighten
these bolts. This is a pivot
point. Snug is tight enough.
16) Backboard Padding
Using six bolts (#23), twelve washers (#32), six
hex nuts (#42) mount backboard padding (#11)
and (#12) to backboard (#5).

15
17) Rim Assembly
Mount Goal Assembly (#6) and Rim Spac-
ers (#36) to Backboard, using four bolts
(#22), eight washers (#31), four lock wash-
ers (#34), and four hex nuts (#28). Tighten
fasteners finger tight, leave them loose
enough to level rim.
DO NOT FORGET to assemble four rim
spacers (#36) between rim and backboard.
If the rim spacers are not used the back-
board will break when rim mounted!
Place a level across rim assembly (#6) and adjust rim until it is level. Finish tightening
the four nuts.
Attach Rim Cover Plate (#7) using four washers (#33), four lock washers (#35), and
four hex nuts (#24).
Check all nuts and bolts and make sure everything is
tightened properly. DO NOT over tighten pivot points, snug is tight enough.
If Backboard Padding (#11 and #12) is not per-installed from the factory use (#23 and
#24) hardware to attach to the backboard frame.
CAUTION: Do not proceed with rim
installation without these spacers!
18) Set Height Meter Sticker
Adjust unit to 7-1/2 feet. Use a tape measure to measure from
the top of the rim to the playing surface. Stick Height Decal to
back of Actuator with the "7.5" mark aligned with bottom of
Black Actuator Sleeve.
19) Post Pad
Secure Post Pad (#13) to front of pole by wrapping straps
around pole and sticking to velcro on opposite side of Pad. Top
Post Pad section should be above Post Ears.

16
20) Maintenance
Like any piece of hardware proper maintenance is required. Several factors such as
the environment, organic materials, herbicides, pesticides, excessive use or misuse
can eventually cause the basketball system to require maintenance. Failure to do so
could result in system failure, property damage, or even personal injury.
1) All organic materials should be kept away from the system at all times. This will al-
leviate any chance of rust penetrating the powder coated finish and causing struc-
tural damage.
Examples: grass clippings, moisture, garbage, dirt, etc.
2) If you see any signs of rust on the system remove the loose paint, sand the area
with a media grit sandpaper and apply outdoor enamel to the affected area.
Suggested Touchup Paint: Rustoleum Semi-Gloss Black Enamel
3) To clean the backboard use a 100% cotton soft cloth with mild dishwashing liquid
for soap and luke warm water. Rinse backboard with lukewarm water. Wash gently
with a 100% Cotton soft cloth, lukewarm water and mild soap. Do not scrub. Rinse
backboard with lukewarm water again. Dry with 100% cotton soft cloth. To minimize
scratches and minor abrasions to your backboard
4) Never adjust the rim below 7’ 6” or over 10’. Adjustments of the goal should be
done under adult supervision. When attempting to slam dunk you should always wear
a mouth guard to avoid dental injury.
5) Replace Net Video—
21) Routine System Inspection
Before each use inspect the entire system for any signs of Loose nuts and bolts, any
excessive wear and tear, any signs of rust or corrosion.
If replacement parts are needed you can contact Pro Dunk® directly or navigate to
www.produnk.com to purchase parts for your system. Only parts provided by Pro
Dunk® should be used for repair. Not doing so could cause the system to fail result-
ing in injury or death and voids the limited warranty.
6-20-2019
Replace Net
produnk.com/video/rim_net_replacement.html

17
NOTE: It is advisable to wait up to
two weeks to allow the anchor footing
to fully cure before aggressive play.

18
Hoops Inc. APOLLO™ Limited 5 Year Warranty
Hoops APOLLO™basketball structural components are warranted to the original purchaser to be free from defects in
material or workmanship for the duration of ownership by the original retail purchaser. The word “defects” is defined as
imperfections that impair the use of the product.
Warranty Fulfillment
Merchandise must be shipped prepaid with a copy of proof of purchase to Hoops Inc. for examination to see whether it
needs to be repaired or replaced. Any labor costs, travel expenses and any other changes involved in the removal,
installation or replacement of the defective/repaired parts from/to your APOLLO™system will be your (the pur-
chaser's) responsibility. Shipping charges for replaced or warranted merchandise being sent back to the customer
must be prepaid by the customer in advance. If not, the replacement shipment will be sent out collect. Hoops Inc. re-
serves the right to examine photographs or physical evidence of merchandise claimed to be defective, and to recover
said merchandise, prior to authorization of warranty claims.
What is not covered by this warranty
 This warranty does not cover defects or damage due to improper installation, Non-residential use, shipping, han-
dling, alteration, accidents, vandalism, weather conditions (rusting), exposure to corrosives, negligence, hanging
on rim, misuse (anything other than a type of basketball activity or related contact with the unit), scratching, scuff-
ing, Acts of God, or any event beyond the control of the Hoops Inc.. If unit is not maintained as stated in the user
manual the warranty will be void.
 Paint or rusted parts. If rust should appear, remove loose paint, sand lighly, primer and paint with exterior flat
matte finish enamel paint.
 HANGING ON RIM WILL VOID THE WARRANTY: Rims are not warranted for any defects other than workman-
ship. Torn back plates, damage springs, bent rings, damaged eyebolts, damaged net ties, and torn or distorted
rim supports result from hanging on the rim and are no warranted.
 Merchandise not intended to be in places of public assembly, such as, but not limited to, schools, parks, public or
private recreational facilities, churches, camps.
 Shipping charges both ways.
 Dealer service charges, labor charges, and travel expenses associated with replacement of repair of warranty
item.
Liability
Hoops Inc. shall not be liable for indirect, special, or consequential damages arising out of or in connection with the
use or performance of the products or other damages with respect to any economical loss, loss of property, loss of
enjoyment of use, costs of removal, installation or other consequential damages for breach of any expressed or im-
plied warranty on these products.
Guidelines
Keep your proof of purchase (original retail purchaser). Without it, we will not be able to proceed with any warranty
service.
1-888-600-8545/ Warranty Dept.
Write
Hoops Inc.
Attn: Warranty Dept
22047 Lutheran Church Rd.
Tomball TX 77377
Email
[e-mail]
For the most up to date warranty information please navigate to www.produnk.com