Artillian 1RMFCH Operating instructions

1 of 6
INSTALLATION & OWNER’S MANUAL
Rev. B, 08/10/2020 p/n: IM-1RMFCH
ARTILLIAN ROPS MOUNTED
FUEL CAN HOLDER
P/N: 1RMFCH
Approximate Set-Up Time
Experienced Dealer Technician – 15 Minutes
Average Dealer Technician – 15 Minutes
Do-It-Yourself – 15 Minutes
Approximate Product Specifications
Overall dimensions: 13.25” L x 17.3” W x 11.5” H
Weight: 19 lbs. (not including mounting bar)
Capacity: 45 lbs.
The Artillian ROPS Mounted Fuel Can Holder is a convenient steel tray for
carrying fuel cans. An included cam-buckle strap with E-track fittings
securely holds a 2-1/2 gallon fuel can and a 1 gallon bar oil can in place
and allows for quick removal on the go. Many E-track locking positions and
additional bungee cord slots suit various fuel can sizes and orientations.
Provisions for carrying a maul or sledge hammer and several wedges
make this the perfect accessory for a day in the woods felling trees.
The quick release Cam Lever Latches allow for easy removal of the Fuel
Can Holder for storage or replacement with one of the many other Artillian
ROPS Mounted Tool Bar Accessories.
For use on Artillian ROPS Mounted Tool Bar (P/N: 1RMTB) (sold separately)
CAUTION Do not exceed the rated capacity for the Fuel Can Holder. Doing so may result in
damage to the Fuel Can Holder and/or the Tool Bar and will void the warranty.
The contents of this envelope are the property of the owner. Leave with the owner when installation is complete.
Comes with 15ft long x 1 inch wide E-Track Cam-buckle Strap (not shown)

2 of 6
SET-UP
SET-UP
1. The design features include many E-Track slots,
bungee cord holes, splitting/felling wedge slots,
several pass through slots for hold-down straps
and various mounting hole locations for a U-bolt.
See figs. 1a, b, & c.
2. Based on the size of your fuel and bar oil cans,
locate the best E-track slots that will securely hold
these items. Install the fixed end of the hold-down
strap first. To install the E-track fitting, pull the
release lever towards the cam buckle, hook the
release lever end of the fitting into the mount and
then insert the other end. Release the lever. See
figs. 2a & b.
Fig. 1a (mounting point option 1) Fig. 1b (mounting point option 2)
Fig. 1c (wedge mount locations)
Fig. 2a (install fixed end of hold-down strap)
Pull back lever
Hook this end
first
Fig. 2b (fixed end of hold-down strap installed)
Splitting & Felling
Wedge Slots
Pass through slots
for hold-downs
Pass throughs slots
for hold-downs
E-Track
Mounting Slots
Bungee Cord
Holes Bungee Cord
Holes
Pass through slots
for hold-downs
Cam buckle
E-Track
Mounting Slots
U-Bolt
Mounting Holes

3 of 6
SET-UP
SET-UP (cont’d.)
3. Install the adjustable length E-track cam-buckle
strap in the desired E-track slot location. Run the
strap through each of the fuel cans’ handles as
shown in fig. 3.
4. Install the adjustable end of strap into the fixed
end’s cam buckle and tighten strap down. Once
fully tightened, cut the excess strap (if desired)
using a pair of scissors.
Remove the fuel can and bar oil from the fuel can
holder prior to the next step.
5. Once the strap is cut to length, use a heat gun or
lighter to singe the cut end of the strap to make
sure that the strap does not fray. See fig. 5.
Note: One E-track cam-buckle strap is provided in the
kit. However, the mount was designed with many E-
track and bungee cord holes to allow the user the
option to add more straps or bungee cords, as desired.
6. A U-Bolt and (4) 3/8-16 flange hex nuts are
included in this kit. These are for carrying a
sledgehammer or maul. There are a set of holes for
this U-bolt on either side of the mount and (4) holes
in the front. The front hole pattern allows for 3
possible U-bolt mounting positions. Loosely install
the U-bolt (in the desired location) and nuts per fig.
6a, then hand tighten. Per fig. 6b, install a
sledgehammer or maul into U-bolt. Make required
adjustments and tighten down the nuts. Note:
make sure that the handle for the tool clears the
rear tire and 3-point hitch arms.
Fig. 3 (install adjustable length hold-down strap end)
Fig. 5 (cut adjustable length hold-down strap end)
Cut and singe
Hold-down strap
CAUTION:
Fig. 6a (install U-bolt and flange nuts for maul)Fig. 6b (adjust U-bolt to fit sledgehammer or maul)

4 of 6
Fig. 7 (attaching a fuel can holder)
ATTACHING AND OPERATION
Fig. 8 (cam lever in the open position)
Fig. 9 (cam lever in the closed position)
rotate both cam levers up
to install the fuel can holder
padlock holes
rotate both cam levers down
to secure the fuel can holder
ATTACH TO MOUNTING BAR:
Note: The Artillian ROPS Mounted Toolbar is designed to
hold multiple accessories at one time. If placed appropriately,
up to 3 separate accessories may be possible. For example,
the Chainsaw Mount, Fuel Can Holder, and Beverage Cooler
Holder were designed to fit on the toolbar simultaneously.
7. Fig. 7 shows a fuel can holder installed onto an
Artillian ROPS Mounted Tool Bar.
8. To install the fuel can holder, rotate both cam levers
UP, then place onto the Tool Bar. See fig. 8.
Note: if the Cam Lever Latches do not sit flush on the Tool Bar, one
of the clamp plates may not have been fully open. Simply remove the
fuel can holder, rotate the cam levers up and tilt the fuel can holder
away from you to ensure the clamp plates are fully open, then
reinstall on the Tool Bar.
9. To secure the fuel can holder to the Tool Bar, rotate
both cam levers DOWN until they cam over. See
fig. 9.
NOTE: For additional security, the fuel can holder can be locked to
the Tool Bar by inserting a padlock through the holes in the mounting
bracket where shown in fig. 9.
10. To remove the fuel can holder from the Tool Bar,
rotate both cam levers UP, then lift the fuel can
holder.
OPERATION
11. For optimal functionality, the cam lever latches are
factory assembled with some friction between the
cam lever and the housing. This ensures the cam
lever doesn’t accidentally flip closed while the user
attempts to install it on the bar. If the cam levers
loosen up over time, simply tighten the nut and bolt
that secure the lever to the housing until the
desired resistance on the cam lever has been
achieved.

5 of 6
1" WIDE HOLD-DOWN, 15' LG, BLACK
P/N: 9SV-9BC06 (QTY.: ONE)
SERVICE PARTS:
CAM LEVER LATCH
P/N: 8SV-110-00071 (QTY.: ONE)
FUEL CAN HOLDER (with Trim Lok)
P/N: 8SV-WA-00368 (QTY.: ONE)
TRIM LOK (10 feet long)
P/N: 9SV-PRO1-10 SAFETY WALK ADHESIVE STRIPS
P/N: 9SV-9PR62-375 (QTY.: 12)

6 of 6
ROPS MOUNTED TOOL RACK
P/N: 1RMTRK
ROPS MOUNTED TOOLBOX, X-LARGE
P/N: 1RMTBXL
MORE ACCESSORIES COMING SOON!
OTHER ACCESSORIES:
ROPS MOUNTED TOOL BASKET
P/N: 1RMTBSK
ROPS MOUNTED TOOLBOX, LARGE
P/N: 1RMTBXS
ROPS MOUNTED CHAINSAW MOUNT
P/N: 1RMCSM
(chainsaw shown for illustration purposes)
BEVERAGE COOLER HOLDER
P/N: 1RMBCH
(cooler shown for illustration purposes)
ROPS MOUNTED 5-GALLON BUCKET
HOLDER - P/N: 1RM5GBH
(Bucket shown for illustration purposes)
TOOL BAR WALL MOUNT
P/N: 1RMTBWM