Atak 7A700 User manual

7” PORTABLE TELEVISION
7A700
Ver 1.0
For technical assistance or troubleshooting
please call 1-855-994-2825 or visit www.sibrandssupport.com
INSTRUCTION MANUAL
MODEL: 7A700

Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (includ-
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
-
paratus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or
Moisture.
shall be placed on the apparatus.
17. The mains plug or appliance coupler shall remain readily operable.
18. Use in outdoors: This TV is not designed for outdoors installation. Do not expose the TV to rain, as it may
become damaged.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Safety:
TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS ARE INSIDE. REFER TO QUALIFIED
SERVICE TECHNICIAN ONLY.
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s
Instruction: The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and servicing instructions in the literature accompanying the
appliance.
to constitute a risk of electric shock to the users.
7A700 - 2

Safety Instructions
Please read these instructions carefully.
This product complies with all applicable US federal safety requirements, as well as those of the Canadian
Standards Association.
1. Cleaning
Always unplug the TV before cleaning. Do not use liquid or aerosol cleaners. Use a soft, slightly damp cloth to
clean.
2. Water and Moisture
Do not use this TV near water. Avoid using this TV in an excessively damp environment.
3. Stand
This TV should always be placed on a solid, sturdy surface.
4. Ventilation
To prevent overheating, do not block or obstruct the vent openings on the TV’s back panel. Also, avoid placing this
TV in a confined area with poor air flow.
5. Power Sources
This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of
The type of power supply to your home, consult your electronics retailer or local power company.
6. Power Cord Polarization
This TV is equipped with a three-wire grounding type plug, a plug with a third (grounding) pin. As a safety feature, this
plug will only t into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician
to replace the obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
7. Power Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from
the TV.
8. Lightning
To protect the TV during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV from lightning
and power-line surges.
7A700 - 3

Safety Instructions
9. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the TV be sure the antenna or cable system is grounded so
as to provide some protection against voltage surges and built up static charges. Article 810 of the National Electri-
cal Code (U.S. A.), ANSI / NFPA 70 provides information with regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of anten-
na-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Example of Grounding According to National
Electrical Code Instructions
NEC - National Electrical Code
10. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power
circuits, or where it can fall on to power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
11. Overloading
12. Object and Liquid Entry
Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short-out
TV.
13. Servicing
Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or
14. Damage Requiring Service
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjustment of other controls may result in damage and will
e. If the TV has been dropped or the cabinet has been damaged.
f. If the TV exhibits a distinct change in performance.
Ground Clamp Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Electric Service
Equipment
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
7A700 - 4

Safety Instructions
15. Replacement Parts
16. Safety Check
Upon completion of any service or repairs to this TV, ask the service technician to perform safety checks to determine
whether the product is in proper operating condition.
17. Heat
The TV should be situated away from heat sources such as radiators, heat registers, stoves, or other products
NOTE TO CABLE / TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric
should be connected to the grounding system of the building, as close to the point of the cable entry as practical.
FCC REGULATORY INFORMATION:
This television has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residen-
tial installation. This television generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
electronic equipment, which can be determined by turning the television off and on, then the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and television.
- Connect the equipment into an outlet on a circuit different from that to which the television is connected.
- Consult your dealer or an experienced radio / TV technician for assistance.
’s
authority to operate the equipment.
guarantee that interference will not occur in a particular installation. If this television does cause interference to other
When replacement parts are required, be sure that only an authorized service technician has used replacement parts
specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards and void any warranty.
7A700 - 5

Table of Contents
Important Safety Instructions.........................................................................................................................................2
Table of Contents ..........................................................................................................................................................6
Introduction....................................................................................................................................................................7
8......................................................................................................................................................yrettaBehtgnigrahC
Remote Control
Overview........................................................................................................................................................................9
TV Overview
01.....................................................................................................................................................................lenaPpoT
Side Panels .................................................................................................................................................................11
Installation
TV Setup
Connect the Telescoping Antenna..................................................................................................................................12
Connect Digital Cable Box, Satellite Receiver, & DVD player with Composite cables (yellow, red, & white) ................12
Initial Setup Wizard .......................................................................................................................................................13
TV Channel Setup & Channel Auto Scan.....................................................................................................................20
Picture Settings
Contrast........................................................................................................................................................................15
Brightness ....................................................................................................................................................................15
Color.............................................................................................................................................................................15
Tint................................................................................................................................................................................15
Sharpness ....................................................................................................................................................................15
Color Temp. ..................................................................................................................................................................15
Audio Settings.............................................................................................................................................................16
Date & Time Settings ..............................................................................................................................................16
Setup Settings
Menu Languages..........................................................................................................................................................17
Transparent ................................................................................................................................................................17
..................................................................................................................................................................17OSD Timeout
Closed Captions.........................................................................................................................................................17
Parental Control ........................................................................................................................................................18
Channel Settings
Favorite ........................................................................................................................................................................19
Show / Hide ..................................................................................................................................................................19
USB & microSD Playback.......................................................................................................................................21
Troubleshooting ........................................................................................................................................................22
7A700 - 6
Installing the Base ........................................................................................................................................................ 8

Introduction What’s In The Box
The 7A700 package includes the following items. Save the carton & packing for future shipping
• Remote Control
• AC 100-240V~50/60Hz to DC 12V 0.8A Adapter
• 12V Auto / Boat Adapter / Charger
• Detachable Telescoping Antenna
• RF Coaxial Extension Cable
• Audio / Video Cable - 3.5mm to Three Female RCA (Red/White/Yellow) Jacks
• Pedestal Base
esaBdnatskciK•
Charging the Battery
This portable tevelvision has a built-in rechargeable lithium-ion battery. The battery can be charged by either the
AC 100-240V to DC 12V Power Adapter or the 12V Auto / Boat Adapter.
Before using the television it is recommended to completely charge the battery by following the steps below.
Home Electrical Outlet Use:
1. Plug the supplied AC 100-240V to DC 12V Power Adapter Jack into the 12V DC Input (10).
2. Insert the wall plug of the Power Adapter into an electrical wall outlet.
3. The Power Indicator LED (7) will turn ON during charging.
4. Once the battery is fully charged the Power Indicator LED (7) will turn OFF.
Auto-Boat Outlet Use:
1. Plug the supplied 12V Auto-Boat Power Adapter Jack into the 12V DC Input (10).
2. Insert the car-boat outlet plug of the Power Adapter into a 12V car-boat outlet.
3. The Power Indicator LED (7) will turn ON during charging.
4. Once the battery is fully charged the Power Indicator LED (7) will turn OFF.
NOTE: A “LOW BATTERY!” message will flash on the TV screen when the battery needs to be charged.
7A700 - 7
NOTE: For the TV to Charge using the Auto / Boat Adapter / Charger, the TV must be turned OFF.

Installing the Base
7A700 - 8
INSTALLING THE PEDESTAL BASE
1. Loosen the square washer on the front of the base by turning the washer counterclockwise.
NOTE: Do not remove the washer from the base.
2. Carefully slide the square washer into the channel on the rear of the TV.
3. Secure the base to the TV by turning the tension knob on the rear of the base clockwise.
INSTALLING THE KICKSTAND BASE
1. Locate the arrow on the rear of the Kickstand Base.
2. Keeping the arrow pointed UP, carefully slide the Kickstand Base into the channel on the rear of the TV.
CHANNEL
SQUARE
WASHER
CHANNEL
ARROW

Remote Control
PICT SOUND
EXIT
ENTER
SOURCE
FREEZE
CH
LIST LIST
FAV
7 - 9A700
1
2
3
4
5
6
7
8
9
1011
12
13
14
15
16 17 18
19
20
21
22
23
24
25
26
28
27
29
30
31
32
33
1. POWER Button
2. CHANNEL UP Button
3. CHANNEL DOWN Button
4. VOLUME UP Button
5. VOLUME DOWN Button
6. MENU Button
7. NAVIGATION UP Button
8. NAVIGATION DOWN Button
9. NAVIGATION LEFT Button
10. NAVIGATION RIGHT Button
11. ENTER Button
12. EXIT Button
13. NUMBER Buttons
14. PREVIOUS CHANNEL Button
15. SOURCE Button
16. ZOOM Button
17. PICTURE FREEZE Button
18. MUTE Button
19. AUDIO Button
20. CLOSED CAPTION Button
21. PICTURE Button
22. SOUND Button
23. PLAY/PAUSE Button
24. STOP Button
25. NEXT Button
26. PREVIOUS Button
27. F. FWD Button
28. F. REV Button
29. ELECTRONIC PROGRAM GUIDE (EPG) Button
30. FAVORITE CHANNELS LIST Button
31. ALL CHANNELS LIST Button
32. SLEEP Button
33. REPEAT Button
34. INFO Button
34
7A700 - 9

CH-CH+ VOL-VOL+
MODE OK
MENU
1 2 3 4 5 6 7
TV Overview
1. POWER Button: Press the POWER button to turn the TV ON / OFF (Standby).
2. MODE Button: Press the MODE button to display the INPUT SOURCE menu.
3. MENU Button: Press the MENU button to display the Setup Menu.
4. CH + / - Buttons: Press the CHANNEL + / -Buttons to select a TV channel.
5. OK Button: Press the OK button to confirm a selected option when using the on-screen menus
6. VOL + / - Buttons: Press the VOL + / - to adjust the Volume up or down.
7. IR Receiver: Receives commands from the Remote Control. When using the Remote
Control, point the Remote at this location and press the desired button.
Top Panel
7A700 - 10

TV Overview
AV IN DC 12V ON / OFF
CH-CH+ VOL-VOL+
MODE OK
MENU
78910 11 12 13
7. POWER INDICATOR LED
8. HEADPHONE JACK
9. AV INPUT
10. 12V DC INPUT
11. ON / OFF SWITCH
12. USB PORT
13. microSD CARD SLOT
Side Panels
7A700 - 11

Installation Connecting to Antenna
ANT
Insert the supplied Telescoping Antenna to the ANTENNA INPUT on the Rear of the TV.
Finger tighten by gently turning the Antenna clockwise. Do not over-tighten.
TELESCOPING ANTENNA
ANTENNA INPUT
Installation Connecting to Composite Input
Note: Reception quality is determined by your location, geographical terrain, and distance from the local
broadcast transmitter.
Audio Video Cable (included)
Digital set top box, gaming console or DVD
CH-CH+ VOL-VOL+
MODE OK
MENU
AV IN DC 12V ON / OFF
• Insert the supplied AUDIO/VIDEO CABLE to the AV IN (9) on the Left Side of the TV.
• Insert a RED, WHITE, & YELLOW AV Cable (Not Included) and into the matching colors on the AUDIO/VIDEO
CABLE ADAPTER.
Red, White, Yellow Cable (Not included)
• Insert the RED, WHITE, & YELLOW AV Cable (Not Included) into the matching colors on the external device.
7A700 - 12

TV Setup Initial Setup Wizard
INITAL SETUP WIZARD
NOTE: the Setup Wizard only appears when turnng on the TV for the first time.
How to Navigate the Setup Menus:
Use the pq arrow buttons on the remote to move to the menu selection.
After connecting the Antenna, turn the television ON using the ON / OFF SWITCH (11).
The quick Setup Wizard will display on-screen to help guide you through the 3 steps listed below:
STEP 1: Choosing a Menu Language
Use the tuarrow buttons on the remote to choose the desired menu option.
Use the pq arrow buttons to select Menu Language.
Use the tuarrow buttons to select English - Francais - Espanol.
Use the qarrow button to select Go to next step and press the
ENTER button to complete the step.
STEP 2: Setting the Time
Use the pq arrow buttons to select Time Zone, Daylight Saving
Time, and Time Format selections.
Use the tuarrow buttons to select the desired setting.
Use the qarrow button to select Go to next step and press the
ENTER button to complete the step.
Setup Wizard
Go to next step
Please select your preferred language
English
MENU ENTER
Menu Language
Setup Wizard
Daylight Saving Time
Time Format
Go to next step
Select the time zone & Daylight saving time
Pacific
Off
12-hour
Time Zone
7A700 - 13
MENU ENTER

TV Setup Initial Setup Wizard
STEP 3: Setting Air/Cable and Channel Auto Scan
Use the tuarrow buttons to select Air or Cable based on your
type of connection (Antenna or Cable without a set top box).
For Antenna & Cable Connections WITHOUT a set top box:
Use the qarrow button to select Go to next step and press the
ENTER button to begin the Channel Auto Scan.
Note: Your type of television connection will determine if you should complete the
Channel Auto Scan part of this step.
Channel Auto Scan may take several minutes to complete.
For Cable/Satellite Connections WITH a set top box:
Press the EXIT button on the remote control to exit the Setup
Wizard.
NOTE: You will see the message “PLEASE RUN AUTO SCAN”
on the screen. Ignore this message as this is not necessary
when using a set top box.
Press the SOURCE button on the remote control to display the
Input Source screen illustrated to the left.
Use the pq arrow buttons to highlight the input where the
set top box was installed. Press ENTER to select the desired
input.
Once Channel Auto Scan has ended, Initial Setup is
complete. You may now begin enjoying your TV, or
make further adjustments to the TV settings which are
explained in the following pages of this manual.
Initial Setup is now complete. You may now begin enjoying your
TV, or make further adjustments to the TV settings which are
explained in the following pages of this manual.
INPUT SOURCE
AV
CARD
TV
USB
Next
IMPORTANT NOTE: If your TV is connected to a Cable or
Satellite set top box DO NOT run the “Channel Auto Scan”
in STEP 3.
Setup Wizard
Go to next step
Select the antenna type then auto scan
Cable
Air / Cable
Setup Wizard
Exit
MENU
Total Found : 0
0:golanA
Digital : 0
RF CH : 2
7A700 - 14
MENU ENTER

Note: When adjustments are completed, you may select another menu by pressing the Menu button.
Menu Adjustments Picture Setting
The Picture menu offers options to enhance and refine the picture displayed on your TV based on ambient room light
and personal preferences. Adjustment options include Picture Mode, Color Mode, Zoom, Noise Reduction & DLC.
How to Navigate:
Press the MENU button on the remote control. Navigate using the pqarrow buttons to select PICTURE. Press the
environments. Depending on the ambient light level in the room, you may find one of the other Picture settings more
pleasing.
To make more critical adjustments based on your own preferences select the Personal mode.
• Brightness
• Contrast
Press down qarrow button to highlight Brightness. Navigate
using the t u arrow buttons to increase or decrease overall
brightness.
Press down qarrow button to highlight Contrast. Navigate
using the t u arrow buttons to increase or decrease contrast
intensity.
Press down qarrow button to highlight Color. Navigate using
the t u arrow buttons to increase or decrease color intensity.
Press down qarrow button to highlight Tint. Navigate using
the t u arrow buttons to adjust colors toward green or reddish
tint.
Press down qarrow button to highlight Sharpness. Navigate
using the t u arrow buttons to soften or view crisper edges in
the picture.
Press down qarrow button to highlight your Color Mode
preference. Navigate using the t u arrow buttons to select
Cool (more bluish tone), Normal or Warm setting.
• Color
• Tint
• Sharpness
• Color Mode
options: Standard - Dynamic - Soft - Personal. The Standard setting is recommended for most brightly lit viewing
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
uarrow button to highlight Picture Mode, then press the uarrow button to select your viewing preference from 4
Picture Mode
Color Mode
Zoom Mode
Noise Reduction
DLC
Standard
Middle
Normal
Wide
On
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
Picture Mode
Contrast
Brightness
Sharpness
Tint
Color
Personal
50
50
50
50
50
Press down qarrow button to highlight your Zoom Mode
preference. Navigate using the t u arrow buttons to select
buttons to select the zoom mode that is most pleasing
• Zoom Mode
7A700 - 15

Menu Adjustments Audio Settings
The Audio menu offers options to make sound enhancements while listening through the built-in speakers or to
headphones connected to the headphone jack.
How to Navigate:
Press the MENU button on the remote control. Navigate using pqarrow buttons to select Audio. Press the qarrow
button to highlight Sound Mode, then press the uarrow button to select your sound preference from 5 factory options:
Standard - Music - Movie - Sports - Personal
Press down qarrow button to highlight Sound Mode.
Press
Press
tubutton to select Music - Movie - Sports - Personal -
Standard.
Music: Preserves the original sound. Good for musical
programs.
Movie: Enhances treble and bass for a rich sound
experience.
Sports: Enhances vocals for TV audio.
Personal: Select to customize audio settings.
Standard: Produces a balanced sound in all environments.
• AVC (Automatic Volume Control)
Press down qarrow button to highlight AVC.
Press tubutton to select (Off - On)
• Sound Mode
•Audio Only
Press down qarrow button to highlight Audio Only.
t u buttons to select (Off-On)
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
Sound Mode
Audio Only
AVC
Standard
Off
Off
Menu Adjustments
Date & Time Settings
The Time menu includes adjustment of settings for your local time zone and daylight savings time. The clock will adjust
automatically after the initial Channel Auto Scan of available broadcast channels in your area.
How to Navigate:
Press the MENU button on the remote control. Navigate using arrow pqbuttons to select Time.
• Press down qarrow button to highlight Sleep Timer then
press the uarrow button to select time to view before the
television timer turns the set off: 5 Min - 10 Min - 15 Min -
30 Min - 60 Min - 90 Min - 120Min - 180 Min - 240 Min - OFF.
• Press down qarrow button to highlight Time Zone then
press the uarrow button to select between: Eastern - Central
- Mountain - Pacific - Alaska - Hawaii - Samoa - Newfoundland
- Atlantic.
• Press down qarrow button to highlight Daylight Savings
Time. Navigate using the t u arrow buttons to select
On or Off.
• Press down qarrow button to highlight Time Format.
Navigate using the t u arrow buttons to select either
12-hour or 24-hour.
• Press down qarrow button to highlight Auto Sync.
Navigate using the t u arrow buttons to turn this
feature On or Off.
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
Sleep Timer
Time Zone
DST
Time Format
Auto Sync
Clock
Wake Up
Off
12-Hour
Eastern
On
On
• Press down qarrow button to highlight Clock.
Navigate using the t u arrow buttons to adjust the time.
• Press down qarrow button to highlight Wake Up.
Navigate using the t u arrow buttons to set an alarm.
7A700 - 16
This feature helps prevent large fluctuations in volume levels.
Press the uarrow button to enter the submenu. When you wish to exit the submenu simply press the MENU button.

Menu Adjustments Setup Settings
In the Setup menu you may change the initial set up of preferences that include settings for language, menu display,
closed captions, resetting your TV back to its factroy default status, or repeat the Setup Wizard.
factory default status.
How to Navigate:
Press the MENU button on the remote control. Navigate using arrow pqbuttons to select Setup. Gain access to
display options by pressing the down qarrow button to highlight Menu Language or other options, then press u
arrow button on your remote to select.
Languages include English, Français, Español.
Navigate using the t u arrow buttons to adjust the
transparency of the on screen display menu.
•Menu Languages
•Transparent
Press the uarrow button to automatically reset all
settings back to their original factory settings.
The TV will request confirmation.
•Restore Default
•Setup Wizard
Set the first time installation options.
Press the ENTER or u button to enter.
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
Menu Language
Transparent
Closed Caption
Restore Default
Setup Wizard
English
0%
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
CC Mode
Basic Selection
Service
Option
CC ON
CC1
1
Menu Adjustments
Note: When adjustments are completed, you may select another menu by pressing the Menu button.
Closed Captions
The Setup menu includes adjustments for activating the Closed Caption text feature for display on-screen and customiz-
ing CC display types and font styles.
How to Navigate:
Press the MENU button on the remote control. Navigate using arrow pqbuttons to select Setup.
• Press the down qarrow button to highlight Closed Caption
then press the uarrow button to highlight CC Mode.
• Press the down qarrow button to highlight Basic Selection
Navigate using the t u arrow buttons to select CC1-4, or
TEXT 1-4.
• Navigate using the t u arrow buttons to select
.ETUMNOCC-NOCC-FFOCC
• Press the down qarrow button to highlight Service.
Navigate using the t u arrow buttons to select 1-6 or OFF.
• Press the down qarrow button to highlight Option.
Press the uarrow button to enter a menu with options to
customize text fonts, colors, and opacities.
7A700 - 17
Press the uarrow button to enter the submenu. When you wish to exit the submenu simply press the MENU button.

PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
Enter Password _ _ _ _
Menu Adjustments Parental Control
In the Lock menu, you mayblock television and movie programming based on TV ratings and Motion Picture Association
guidelines. To gain access and select your preferences within the Parental menu make certain your input is set to TV.
How to Navigate:
Press the MENU button on the remote control. Navigate using arrow pqbuttons to select Lock. Gain access to
parental rating options by pressing the down uarrow button to highlight Enter Password. Enter your 4 digit code
(factory default code is “0000”) unless previously changed.
• To change the password, press the uarrow button to display
a screen to set a new password. You will first be required to
enter the old password, then enter the new password, then
confirm again. (not illustrated)
• To make changes to the parental controls, higlight System
Lock then press the uarrow button to turn the lock ON.
• To set parental controls for television programming or DVD
movies, press the qp arrow buttons to highlight US.
Navigate using the tubuttons to highlight TV / MPAA menus.
• Highlight TV, then press the uarrow button to highlight the
TV Ratings and press ENTER to select your preference.
• Highlight MPAA, then press the uarrow button to enter the
MPAA menu. Press the parrow button repeatedly until you
reach the maximum allowed rating.
TV-Y
Appropriate for all children
TV-Y7
Appropriate for children over 7
TV-G General Audience
TV-PG Parental Guidance Suggested
TV-14 Parents Strongly Cautioned
TV-MA Mature Audience Only
G General Audience
PG Parental Guidance Suggested
PG-13 Parents Strongly Cautioned
RRestricted
NC-17 No One Under 17 Permitted
XAdults Only
• To block access to either TV or the AV Input, choose Input
Block then use the uarrow button to confirm your selections.
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
TV RATING
ALL
ALL
ALL
ALL
ALL
ALL
FV
V
V
V
S
S
S
L
L
L
D
D
D
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
G
PG
PG-13
R
NC-17
X
N / A
MPAA
LOCK
LOCK
LOCK
LOCK
7A700 - 18

PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
Air / Cable
Auto Scan
Favorite
Show / Hide
DTV Signal
Air
Menu Adjustments
Channel Settings
The Channel menu provides the setup / changes to your television provider to receive broadcast channels, store
your favorite channels, and the option to show / hide channels in memory.
How to Navigate:
Press the MENU button on the remote control. Navigate using arrow pqbuttons to select Channel
• Favorite
Good
• Air / Cable
Press the uarrow button to choose AIR or CABLE based on
your TV provider.
Press the uarrow button to enter the Favorites List Menu.
Navigate using the pq arrow buttons to highlight your favorite
channels. Press ENTER on a highlighted channel to mark or
unmark that channel as a Favorite. A heart symbol will appear
next to all channels marked as Favorites.
NOTE: to access your Favorites simply press the FAVORITE
• Show / Hide
Press the uarrow button to enter the Show / Hide Menu.
Navigate using the pq arrow buttons to highlight channels
you wish to add or remove from the list of available channels.
Press ENTER on a highlighted channel to Show or Hide the
highlighted channel. Channels marked with a Wwill be removed
from the list of available channels.
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
2.1 WOI-TV
5.1 KCCI
9.1 KGAN
10.2 KFXA
FAVORITE


PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
2.1 WOI-TV
5.1 KCCI
9.1 KGAN
10.2 KFXA
SHOW / HIDE
W
CHANNELS LIST button (30) on the Remote Control.
7A700 - 19
Press the uarrow button to enter the submenu. When you wish to exit the submenu simply press the MENU button.

TV Settings TV Provider Changes &
Channel Auto Scan After Initial Setup
To enter the Channel Menu:
• Press the MENU button
• Using the pqarrow buttons; scroll to highlight Channel
• Press the down uarrow buttons to highlight Air / Cable
Air Mode
Select Air when TV is connected to either the provided Telescoping Antenna, or a separate indoor / outdoor antenna.
• Press the t u arrow button to highlight Air.
•
NOTE: Channel Auto Scan may take several minutes to complete.
set top box to the AV INPUT (9), press the SOURCE button (15) on the Remote, and choose the AV input from the
Note: For Cable or Satellite users with a set-top box, there is no need to run Channel Auto Scan. Connect your
To make changes your TV provider or re-scan for available broadcast channels in your area, select the Channel Menu.
Press the qarrow button to highlight Auto Scan and press ENTER. Press the uarrow button to highlight YES
and press ENTER to begin Auto Scan.
the INPUT SOURCE LIST.
Select Cable if you subscribe to a pay television service without a set top box.
• Press the t u arrow buttons to highlight Cable.
•
NOTE: Channel Auto Scan may take several minutes to complete.
Cable Mode
Press the qarrow button to highlight Auto Scan and press ENTER. Press the uarrow button to highlight YES
and press ENTER to begin Auto Scan.
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
Air / Cable
Auto Scan
Favorite
Show / Hide
DTV Signal
Air
Good
PICTURE
AUDIO
TIME
SETUP
LOCK
CHANNEL
Air / Cable
Auto Scan
Favorite
Show / Hide
DTV Signal
Cable
AUTO SCAN DTV + ATV
FOUND
ANALOG
DIGITAL
55% COMPLETE
7 CHANNELS
0 CHANNELS
7 CHANNELS
AUTO SCAN DTV + ATV
FOUND
ANALOG
DIGITAL
55% COMPLETE
7 CHANNELS
0 CHANNELS
7 CHANNELS
7A700 - 20