Atdec AWMS-2-D13-C User manual

AWMS-2-D13-C | Page 1 of 13
Installation Guide
AWMS-2-D13-C
2 x Dynamic Arms on 135 Post with C-Clamp
COMPONENT CHECKLIST RANGE
CONTENTS
B
AWM-AD
Dynamic Arm
(x2)
D
AWM-FC
C-Clamp
(x1)
A
AWM-LC
Post Clamp (x1)
C
AWM-P13
135 Post
(x1)
C-Clamp
Page 2
Page 3
135 Post
Page 6
Page 7
Post Clamp
Page 8
Page 9
Dynamic Arm
Page 10
Page 11
Page 12
Page 13
AWM-FC
Component Checklist
Clamp Installation
AWM-P13
Component Checklist
Post Installation
AWM-LC
Component Checklist
Post Clamp Installation
AWM-AD
Component Checklist
Arm Installation
Monitor Installation
Cable Management

AWMS-2-D13-C | Page 2 of 13
AWM-FC
C-Clamp
AWM-FC Page 1 of 4
Installation Guide
AWM-FC
C Clamp
COMPONENT CHECKLIST REQUIRED TOOLS
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with Atdec modular (AWM) products.
! The manufacturer accepts no responsibility for incorrect installation.
A
C Clamp Bracket
(x1)
B
C Clamp Plate
(x1)
C
Cover for Post
(x1)
D
Cover for Base
(x1)
E
4mm
Allen key
(x1)
F
5mm
Allen key
(x1)
• All tools supplied
A
C Clamp Bracket
(x1)
B
C Clamp Plate
(x1)
C
Cover for Post
(x1)
D
Cover for Base
(x1)
E
4mm Allen key
(x1)
F
5mm Allen key
(x1)

AWMS-2-D13-C | Page 3 of 13
AWM-FC Page 2 of 4
1. C Clamp overview
2. Re-configure Clamp
1.1 Default - This is the “out of the box” configuration
MIN THICKNESS - 25mm ( 1”)
MAX THICKNESS - 33mm (15
/
16”)
MIN THICKNESS - 18mm (11/
16”)
MAX THICKNESS - 25.8mm (1”)
1.2 Inverted - The C Clamp can be reconfigured for thicker surfaces
2.1 Slide pad off 2.3 Invert pad 2.3 Slide pad back on
Fasteners
supplied
with post
Tighten
Firmly
!
3.2 Place in desired location 3.3 Slide the C Clamp bracket over the plate
and position screw tips in the indents on
the base plate
Note: You may need to un-screw the set screws
out of the plate using the allen key
3.1 Attach plate to post
3. Post mount configuration
Desk Clamp
Bracket
Mounting
surface
Pad
M8 x 16mm
Set Screw
3.4 Check the set screws are mounted in position. Also check the
desk clamp bracket is positioned tight up against the mounting
surface edge
3.5 Tighten the set screws firmly and evenly on both sides of the
desk clamp bracket.

AWMS-2-D13-C | Page 4 of 13
AWM-FC Page 3 of 4
4. Installing the clamp cover to post
5. Base mount installation
4.1 Remove the cable cover by pulling it
straight up and out of the post. Remove
top cap if already installed
5.1 Attach plate to base
5.5 Tighten the set screws firmly and evenly on both sides of the
desk clamp bracket
5.4 Check the set screws are mounted in position. Also check the
desk clamp bracket is positioned tight up against the mounting
surface edge
4.2 Locate the C Clamp cover over the
post. Guide over the holes in the base
plate and gently apply pressure on the
cover until it clicks into place
5.2 Place the base and plate in desired
location
4.3 Re-attach the cable cover by sliding
it into the post channel. Fit the pole and
cover caps back on.
5.3 Slide the bracket onto the base plate
and position screw tips in the indents on
the base plate
Note: You may need to un-screw the set
screws out of the plate using the allen key
Fasteners
supplied
with base
Tighten
Firmly
!
!
Desk Clamp
Bracket
Mounting
surface
Pad
M8 x 16mm
Set Screw
Click!

AWMS-2-D13-C | Page 5 of 13
AWM-FC Page 4 of 4
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20180502D
6. Installing the clamp cover to base
6.1 Locate the Cover for Base over the base. Guide over the
holes in the base plate and gently apply pressure on the cover
unitl it clicks into place.
6.2 Installation Complete
To continue with intallation of your monitor arm, refer to
your monitor arm’s installation guide.
Click!

AWMS-2-D13-C | Page 6 of 13
AWM-P Page 1 of 2
Installation Guide
AWM-P
Post
COMPONENT CHECKLIST
REQUIRED TOOLS
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with Atdec AWM Series products.
! The manufacturer accepts no responsibility for incorrect installation.
• All tools provided
A
Post
(x1)
C
Screw
M8
(x2)
F
Cable clips
(not supplied
with all posts)
B
Post Cap
(x1)
E
Cable Cover
(x1)
(not supplied
with all posts)
D
Cable Cover Cap
(x1)
(not supplied
with all posts)
AWM-P
Post
A
Post
(x1)
C
Screw M8
(x2)
F
Cable clips
(not supplied
with all posts)
B
Post Cap
(x1)
E
Cable Cover
(x1)
(not supplied
with all posts)
D
Cable Cover Cap
(x1)
(not supplied
with all posts)

AWMS-2-D13-C | Page 7 of 13
AWM-P Page 2 of 2
Rear of Mounting
Surface
Rear of Mounting
Surface
Rear of Mounting
Surface
Rear of Mounting
Surface
1. Attach Post to fixing (fixing sold seperately)
2. Check post placement & arm positions
4. Cable clips and cover
3. Cable cover position and post cap
2.1 Do not mount a monitor arm on the rear channel
of a post when the post is fixed to the desk using an
F Clamp, Heavy Duty F Clamp, or C Clamp.
4.1 Push the cable down into
the cable clip.
4.2 Insert one side of the
cable clip into the channel on
the post assembly, then push
in the other side.
3.1 To reposition the cable cover, pull it
straight up and out of the post and insert
it into any of the available channels
3.2 Optional cable cover positions 3.3 Fit post cap onto the top of the post
Note: The cable cover shown does not
come with all posts
Note: Cable clips do not come with all
posts. Additional clips sold separately.
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20180518E
Cable Cover
Allen Key
Post Cap
Post
Note: An allen key
may be stored in
the Post Cap.
F Clamp
AWM-FF
Heavy Duty
F Clamp
AWM-FH
C Clamp
AWM-FC
FC
C Clamp
FB
Bolt
Through
Kit
AC-GC
Grommet
Clamp
FH
HD F Clamp
FF
F Clamp
FC
C Clamp
FB
Bolt
Through
Kit
AC-GC
Grommet
Clamp
FH
HD F Clamp
FF
F Clamp
AWM Fixing options
Bolt Through
Kit
AWM-FB
F Clamp
AWM-FF
Heavy Duty
F Clamp
AWM-FH
C Clamp
AWM-FC
Grommet
Clamp
AC-GC
1.1 Follow the installation
guide provided with your
xing to attach it to the post
and t it to the worksurface.
4.3 Loop cable and insert
into cable cover.
4.4 Feed remaining cable
into the cover.

AWMS-2-D13-C | Page 8 of 13
AWM-LC Page 1 of 2
COMPONENT CHECKLIST
Installation Guide
AWM-LC
Post Clamp
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with AWM Series Arms, Posts and Wall Channels.
! The manufacturer accepts no responsibility for incorrect installation.
REQUIRED TOOLS
• All tools provided
A
Post Clamp
(x1)
AWM-P
Post Clamp

AWMS-2-D13-C | Page 9 of 13
AWM-LC Page 2 of 2
1. Fix Clamp to Post or Wall Channel
3. Fit AWM Series arm to Post Clamp
1.1 Ensure knob is undone.
2.1 Remove plastic sleeve.
3.1 Push arm onto clamp.
1.2 Slide Post Clamp into channel.
2.2 Remove rotation ring
3.2 Ensure arm is fully pushed onto clamp.
Push knob to
aid insertion
1.3 Hold clamp in desired position on post
and turn knob to lock in place.
2.3 Place rotation ring in the desired position.
3.3 Tighten joint screw.
Note: Check the
arm rotation is
smooth after
tightening.
Note: Arm sold
separately
Note: Place the rotation ring
depending on what post channel
the arm will be attached to. The tag
should always face towards the user.
1. Ensure Knob is undone
1. Remove plastic sleeve
Tip: push knob
to aid insertion
2. Slide post clamp into channel
2. Remove rotation ring
1. Press
2. Lift
3. Hold clamp in desired position on post and turn
knob to lock in place
3. Place the rotation ring
in the desired postion
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20180518A - E02
180°
360°
OR
Default
Position
Flipped
Position
Tag
1. Push arm onto clamp
2. Ensure arm is fully pushed onto clamp
3. Tighten set screw
Tip: Check the
arm rotation is
smooth after
tightening.
2. Set arm rotation to 180° (optional)
Note: default arm rotation is set to rotate 360�

AWMS-2-D13-C | Page 10 of 13
AWM-AD
Dynamic Arm
AWM-AD Page 1 of 4
Installation Guide
AWM-AD
Dynamic Arm
COMPONENT CHECKLIST
REQUIRED TOOLS
A
Dynamic
Monitor Arm
(x1)
B
VESA
head
(x1)
C
Screw
M4x25mm
(x4)
D
Screw
M4x16mm
(x4)
E
Screw
M4x12mm
(x4)
F
Spacer
(x4)
G
Security
screw
(x1)
H
4mm
allen key
(x1)
• Phillips Head Screwdriver
WEIGHT RANGE
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with Atdec AWM Series products.
! The Dynamic Arm (AWM-AD) requires a Channel Clamp (AWM-LC, sold separately) for installation on an AWM Post.
! The Dynamic Arm (AWM-AD) requires a Desk Base (AWM-LB, sold separately) for installation directly onto an AWM fixing.
! The manufacturer accepts no responsibility for incorrect installation.
0 - 9kg
(0 - 20lbs)
A
Dynamic
Monitor Arm
(x1)
B
VESA
Head
(x1)
C
Screw
M4x25mm
(x4)
D
Screw
M4x16mm
(x4)
E
Screw
M4x12mm
(x4)
F
Spacer
(x4)
G
Security
Screw
(x1)
H
4mm
Allen Key
(x1)

AWMS-2-D13-C | Page 11 of 13
AWM-AD Page 2 of 4
1. Set arm rotation to 180° (optional)
2. Fit arm onto Base or Channel Clamp (sold separately)
Note: Check the
arm rotation is
smooth after
tightening.
2.1 Push arm onto shaft. 2.2 Ensure arm is fully pushed onto shaft. 2.3 Tighten joint screw.
1.1 On the Base or Channel
Clamp (sold separately)
Remove plastic sleeve.
1.2 Remove rotation ring. 1.3 Place rotation ring in the
desired position.
Channel Clamp Ring Position
When setting channel clamp rotation,
orientate the ring depending on what
post channel the arm will be attached
to. The tag on the ring should always
face towards the user.
180°
360°
OR
Default
Position
Flipped
Position Tag
1. Press
2. Lift
3.2 Attach VESA head onto monitor with
provided screws.
3. Attach VESA head to monitor
100mm
75mm
100mm
75mm
Flush
Too long Too short
Spacer
5mm 12mm
3.3 Be sure to use correct screw length3.1 VESA mounting compatibility
100mm
75mm
100mm
75mm
Flush
Too long Too short
Spacer
5mm 12mm
Note: For other sizes, use a suitable
adaptor plate (sold separately).
Note:
Spacers may
be required
for curved,
recessed
or uneven
monitor
surfaces.
4. Mount monitor on arm
Monitor arm
4.2 Ensure that the VESA head sits ush within
the monitor arm. There should be no gap.
4.1 Insert VESA head into the monitor arm 4.3 Push the lever down to secure
it to the arm assembly
Gap No Gap

AWMS-2-D13-C | Page 12 of 13
AWM-AD Page 3 of 4
5. Adjust tilt tension & install security screw
5.1 Use the allen key to adjust the tilt tension until the monitor
holds in a vertical position at the end of the arm.
Note: Support
monitor while
adjusting.
Tighten
Loosen
Tighten
Loosen
5.2 OPTIONAL security screw
Tilt the head upwards to install the optional security screw.
7. Tension gauge
7.1 When installing
multiple monitors
of a similar weight,
use the tension
gauge to make
installation faster.
1. Set up one monitor and
record the position of the
marker on the gauge.
2. When installing subsequent
monitors, pre-tension the
arm to the recorded amount,
then ne-tune the tension by
following steps 6.3 to 6.5.
Arm Tension Gauge
Marker
Heavier
Monitor
Lighter
Monitor
6. Adjust arm tension
6.1 To accurately set the tension of the arm, position
the monitor at 90 degrees
6.2 Use the allen key to adjust the arm tension to the weight of the
monitor. Follow steps 6.3 to 6.5 to set the tension.
6.3 If the monitor sags or falls down,
increase the arm tension by rotating
the screw clockwise.
6.5 If the monitor oats or hovers in all
positions the arm tension is balanced
and does not require further adjustment.
6.4 If the monitor springs upwards from the
bottom position, decrease the arm tension
by rotating the screw anti-clockwise.
Monitor Falls
(from top)
Increase Tension
Monitor ‘Floats’
(all positions)
Balanced
Monitor Springs
(from bottom)
Reduce Tension
90°

AWM-A46 Page 4 of 4
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20180521C
Note: The cable cover shown
does not come with all posts
7.4 To reposition the cable cover, pull it
straight up and out of the post and insert
it into any of the available channels
Cable cover
Cable
Cover
Desk
Clamp
7.1 Push the cable down into the cable clip
Note: Cable clips do not
come with all posts
7.6 Feed remaining cable into cover
7.5 Loop cable and insert into cable cover
7.2 Push cable clip into post channel
7. Post cable management
7.3 Recommended post cable cover
position for double or triple arm set-ups
Note
Ensure enough cable
slack is given to allow for
movement of the monitor
Push
6. Monitor arm cable management
6.1 Plug cables into the monitor and route
the cables down the arm using the cable
hooks and clips
Alternative cable
cover positions
AWMS-2-D13-C | Page 13 of 13
AWM-AD Page 4 of 4
8. Cable management
8.1 Plug cables into the monitor and
route the cables down the arm using
the cable hooks and clips.
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20180727
See steps 8.2 to 8.4
8.2 Wedge cable into the central gap
and slide it down the arm.
8.3 The cable should slip into the arm cavity 8.4 Slide the remaining loose cable
from the central gap up the arm.
Important!
Ensure enough cable slack is
given in this area to allow for
movement of the monitor.