EverDesk+ Max Frame User manual
assembly manual
Max Frame
www.everdeskplus.com
Tools
Parts List
EVERMAXV3.0-WH-S | EVERMAXV3.0-BLK-S
Max Frame
Assembly
Information
13
14
1
3a
3b
4
7
6
8
10
11
12
9
15
16
17
18
or
5
2
M8x38mm Pan Head Screw 8
M6x14mm Machine Screw 8
19
17
Leg
12
Foot
22
Frame End-CB
3a1
Frame End
3b1
Center Rail
42
Side Bracket
52
Lock Buckles
62
Control Box
71
8
Foot Glides 4
M6x18mm Hexagon Socket
half-thread screw 8
ST5x20mm Wood Screw 7
9
10
11
12
14
13
15
16
Parts Qty Parts Qty
18
M6x12mm Pan Head Screw 4
Health Coach Controller* 1
M4x12mm Phillips Head
Machine Screw* 2
Power Cord 1
Extension Cable 1.3m 1
Cable Clip 10
ST5x16mm Wood Screw* 2
20
*These parts can be found in the Health Coach Controller Kit.
Cable Tray 1
Caution | Settings
www.everdeskplus.com
WARNING! Failure to follow these instructions may result in serious injury.
Ensure no obstacles are in the desk’s path. Ensure the desktop is not touching any walls.
Ensure all cords are an appropriate length to accommodate the changes in height.
This height adjustable desk has electric motors and is designed for use in dry work areas only. The desk height is adjustable so that it can be
positioned at the most ergonomically suitable height. Any other use comes at the user’s risk. Under no circumstances will EverDesk+ accept
warranty claims or liability claims for damages caused from improper use or handling of the desk frame.
Keep Children away from electric height-adjustable desks, control units and handsets.
There is a risk of injury and electric shock.
Do not sit or stand on the desk frame. Do not crawl or lie under the desk frame.
Do not place any objects taller than 50cm underneath the desk.
Keep liquids away from all electrical components.
Do not open or dismantle any of the components - the Legs, Control Box, or Switch.
There is a risk of electric shock.
This product is designed with a duty cycle of 10% (2 minutes on, 18 minutes off).
i i
In the event of a power outage or if the power cords is unplugged,
a manual reset may be necessary.
i i
Health Coach Controller Troubleshooting
Ensure that the desk it at its lowest height before attempting to reset.
• Turn the controller anti-clockwise
(DOWN position) and hold until the
display reads “RESET”, then release the
controller.
• Press and hold the “1” button while the
display flashes “RESET” and then
switches to either:
10.1 ( = One Touch)
10.2 ( = Constant touch)
• Press the “1” button again until desired
setting is reached. Once the chosen
setting is displayed, release the button
and wait about 5 seconds for the
display to return to “RESET”.
• Finish the reset process by turning the
controller anti-clockwise and holding it
until the desk lowers further, slightly
rises and stops.
The new touch settings will have been
saved - the desk is now ready to use.
Touch Settings
• Turn the controller anti-clockwise (DOWN
position) and hold until the display reads
“RESET”, then release the controller.
• Press and hold the “2” button while the
display flashes “RESET” and then
switches to either:
10.3 ( = CM)
10.4 ( = Inches)
• Press the “2” button again until desired
setting is reached. Once the chosen
setting is displayed, release the button
and wait about 5 seconds for the display
to return to “RESET”.
• Finish the reset process by turning the
controller anti-clockwise and holding it
until the desk lowers further, slightly rises
and stops.
The new unit settings will have been saved
- the desk is now ready to use.
Changing Measurement Units (CM/Inch)
• Enter Reset Mode: Turn the controller
anti-clockwise (DOWN position) and hold
until the display reads “RESET”, then
release the controller.
• Finish Reset: Turn and hold the DOWN
position again until the desk lowers itself
to the minimum height, slightly rises and
stops.
The desk will have been reset.
Reset Health Coach
Health Coach
User Guide
Please scan the QR
code to view all the
features and
recommended
uses of our Health
Coach Controller.
• Turn the controller anti-clockwise (DOWN position) and hold until the display reads “RESET”, then release the controller.
• Press and hold the EverDesk+ Logo for about 5 seconds until the minimum height is displayed.
• Turn the controller anti-clockwise or clockwise to decrease or increase the height value respectively.
• Finish the reset process by turning the controller anti-clockwise and holding it until the desk lowers further, slightly rises and stops.
The new height value is saved and the desk is ready to use.
Manually Change Displayed Height Value
Assembly
Mounting Side Brackets
STEP ONE:
• Align the four M6x18 Hexagon
Socket Half-Thread Screw (Part
10) on the Leg with the four slots
on the Frame End (Parts 3a/3b).
• Place Leg (Part 1) into the
frame, making sure to catch the
front and rear screws into their
respective slots. Slide the Leg
forwards slightly - towards the
Lock Buckles (Part 6)- to lock it in
place.
• Align the hooked ends of the
Lock Buckles with the two front
screws (Part 10).
• Ensure that the cable exiting
the Leg runs under the Lock
Buckle (Part 6).
• Press down on the middle of
the Lock Buckle firmly with your
palm to lock the Leg, Frame and
Side brackets all together.
* Please note that the M6x18 Hexagon Socket Half-Thread Screw (Part 10) are pre-installed on the Leg (Part 1).
** Please note that the Lock Buckles (Part 6) are pre-installed on the Frame Ends (Part 3a/b)
• Slide Side Brackets (Part 5) into Frame Ends (Parts 3a and 3b).
Locking the Leg, Frame and Side Brackets
2STEP TWO:
3a3b
5
Step 2a: Align Leg in Frame
Step 2b: Lock into Place
6
run leg
cable under
lock buckle
Press down
Firmly
1
3a
3b
6
10
front screw
rear screw
Pinching Risk :
Please be mindful of your fingers
Attaching the Foot
STEP FOUR:
4
• Place Foot (Part 2) on top of Leg (Part 1).
• Insert four M6x14mm Machine Screws (Part 12) and tighten in a cross pattern
• Repeat for the other side.
1
2
9
12
* Please note that the Foot Glides (Part 9) are preinstalled on the foot.
Assembly
13
or
14 5
Center Hole:
centralise between
Frame Ends
4
Attaching Frame to Table Top
STEP THREE:
3
A. For Pre-Drilled Table Tops: B. For Table Tops without
Pre-Drilled Holes:
• Place frame on table top.
• Adjust frame to align with pre-drilled
holes on table top. Using the center
holes as a marker, ensure that the
Center Rails (Part 4) are centralised
between the two frame ends.
• Insert and tighten M6x12mm Pan
Head Screw (Part 14) to attach frame
to table top (Via Side Brackets (Part 5)).
• Repeat for all four corners.
• Place frame on table top.
• Double-check the frame is properly
positioned on the underside of the
table top. Using the center holes as a
marker, ensure that the Center Rails
(Part 4) are centralised between the
two frame ends.
• Attach frame to underside of table
top using four ST5x20mm Wood
Screws (Part 13) provided.
Assembly
Installing the Control Box
STEP FIVE:
5
• Install the Control Box (Part 7) into Frame (Part 3a) by slotting it into place.
• Connect the Leg cables to the control box.
• Use Extension Cable (Part 17) if the leg cable is unable to reach the control box.
• Connect the Power Cord (Part 16) to the Control Box.
3a
3a7
16
17
• Turn Health Coach Controller (Part 15)
upside down and place it onto the
underside of the table top.
• Align Health Coach Controller to
desired position (either left or right of
worktop). For pre-drilled worktops, use
M4x12mm Pan Head Screws (Part 19)
to secure the Health Coach in place.
Use ST5x16mm Wood Screws (Part 20)
for non-drilled worktops.
• Plug in cable* to Health Coach
Controller, and connect the other end
of the cable to the Control Box (Part 7).
*Cable comes packaged with Health Coach Controller.
Installing the Controller
STEP SIX:
6
7
15
19
20
or 15
Flipping your new EverDesk+ Over
STEP EIGHT:
8
Make sure to flip the desk over on its rear edge – do not flip the table on the
side with the controller installed.
• Grab desk base and flip assembled table right side up.
• Plug Power Cord (Part 14) into outlet to power the desk.
Assembly
Installing the Cable Tray
STEP SEVEN:
7
• Position the Cable Tray (Part 8)
on the Frame (Part 3a/b).
• Using eight M8x38mm Pan
Head Screws (Part 11) and the
allen wrench provided, secure
the Cable Tray to the Frame.
8
11
www.everdeskplus.com
v1.0_080222
EVERMAXV3.0-BLK-S
EVERMAXV3.0-WH-S
assembly manual
Max Frame
Table of contents
Other EverDesk+ Rack & Stand manuals
