Attero Tech Dante unD6IO-BT User manual

 Attero Tech, LLC
1315 Directors Row, Suite 107, Ft Wayne, IN 6808
Phone [phone] • Fax [phone]
www.atterotech.com
61 -00033
unD6IO-BT
Bluetooth ® Multi-I/O Wall Plate
User Manual
Date 6/19/2018
Revision 01_c

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 1 61 -00033 Rev 01_c
IMPORTANT SA ETY INSTRUCTIONS
The symbols below are internationally accepted symbols that warn of potential hazards with electrical products.
This symbol, wherever it appears, alerts you to the presence of un-insulated dangerous voltage inside the
enclosure -- voltage that may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the
accompanying literature. Please read the manual.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
10. Only use attachments/accessories specified by Attero Tech
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
13. If rack mounting, provide adequate ventilation. Equipment may be located above or below this apparatus but
some equipment (like large power amplifiers) may cause an unacceptable amount of hum of may generate too
much heat and degrade the performance of this apparatus,
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 2 61 -00033 Rev 01_c
LIMITED IVE YEAR WARRANTY
The equipment is warranted for five years from date of purchase from Attero Tech, LLC against defects in materials or
workmanship. This warranty does not cover equipment which has been abused or damaged by careless handling or
shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Attero Tech,
LLC will, at our option, repair or replace any defective parts without charge for either parts or labor. If Attero Tech, LLC
cannot correct the defect in the equipment, it will be replaced at no charge with a similar new item. Attero Tech, LLC
will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Attero Tech,
LLC, shipping costs prepaid, within five years from the date of purchase. This Limited Warranty is governed by the laws
of the State of Indiana. It states the entire liability of Attero Tech, LLC and the entire remedy of the purchaser for any
breach of warranty as outlined above. NEITHER ATTERO TECH, LLC NOR ANYONE INVOLVED IN THE PRODUCTION OR
DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR
INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF ATTERO TECH, LLC HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF ATTERO TECH, LLC
EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT.
This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules and EN55022. These limits are
designed to provide reasonable protection against harmful interference when
the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference,
in which case the user will be required to correct the interference at their own expense.
This symbol means the product must not be discarded as household waste, and should be delivered to an
appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources,
human health and the environment. For more information on disposal and recycling of this product, contact
your local municipality, disposal service, or the business where you bought this product.

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 3 61 -00033 Rev 01_c
Contents
1 – Overview..................................................................................................................................................................................................................... 4
1.1 – What’s in the Box .....................................................................................................................................................
2 – Product eatures .................................................................................................................................................................................................... 5
2.1 – Audio Signal Flow ..................................................................................................................................................... 7
3 – Mounting and Installation ................................................................................................................................................................................. 8
3.1 – Error Reporting ....................................................................................................................................................... 10
3.2 – Hardware Connections ........................................................................................................................................... 10
3.3 – Factory Reset .......................................................................................................................................................... 10
4 – Device eatures and Settings ........................................................................................................................................................................ 11
.1 – Bluetooth® Pairing/Connect Modes ....................................................................................................................... 11
.1.1 – Manual Mode .................................................................................................................................................. 11
.1.2 – Reconnect Mode ............................................................................................................................................. 11
.1.3 – Exclusive Mode............................................................................................................................................... 11
.2 – Bluetooth® Audio Bridging ..................................................................................................................................... 12
.2.1 – Media Bridging (only) ..................................................................................................................................... 12
.2.2 – Call Bridging (only) ......................................................................................................................................... 13
.2.3 – Call & Media Bridging ..................................................................................................................................... 13
.3 – Bluetooth® Pass-through AVRCP (AV Remote Control Protocol)............................................................................ 1
. – Other Input Controls .............................................................................................................................................. 1
.5 – Output Controls ..................................................................................................................................................... 1
5 – Configuration Workflow .................................................................................................................................................................................. 15
5.1 – IP Address Setup .................................................................................................................................................... 15
5.2 – Software Configuration and Control ...................................................................................................................... 16
5.3 – 3
rd
Party Control ..................................................................................................................................................... 16
5.3.1 – API Documentation ........................................................................................................................................ 16
5.3.2 – Control Interface Type ................................................................................................................................... 16
5.3.3 – Using the Command interface ....................................................................................................................... 16
6 – ARCHITECTS & ENGINEERING SPECI ICATION ...................................................................................................................................... 17
Device Specifications ................................................................................................................................................................................................ 18

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 61 -00033 Rev 01_c
1 – Overview
The unD6IO-BT Dante™ Audio Interface with Bluetooth® is a cost effective multi‐IO wall box. The unD6IO-BT features
stereo Bluetooth® wireless audio input connectivity along with two RCA line level inputs and a 3.5mm TRS line level input.
A 3.5mm TRS line level output on the front is also included.
The unD6IO-BT is designed to fit into most dual gang US junction boxes and is PoE enabled, so all connectivity (power,
control and audio data) is provided by a single CAT‐5e/6 cable. The unD6IO-BT’s unique mix of consumer style wired and
wireless connectivity allows easy connection of a wide variety of user devices to a Dante™ network with no concerns about
ground loops or other audio problems common with consumer devices.
The unD6IO-BT includes the following features:
oSimple pairing one button pairing/connect process for standalone operation with LED indication of connection
status
oConfigurable pairing button for use with and without 3rd party control systems
oCustomizable Bluetooth® friendly name in applications with co -located unD6IO-BTs
oCompatible with most smartphones, Apple iPads, and Android tablets
oTwo RCA and one 3.5mm stereo input
oOne 3.5mm stereo output with software volume control
oIEEE802.3af compliant PoE powered to work with any compliant PoE network switch
oRCA inputs and 3.5mm input (carried as stereo) can be selected individually or in combination as an audio flow
via software (see Audio Flow diagram)
oBluetooth® audio is carried as stereo onto the Dante™ network
oBluetooth® call bridging capability for conferencing purposes
1.1 – What’s in the Box
The device comes supplied with the following:
o(1) unD6IO-BT ( P/N 900-00193)
o*Note: This product is available in different color and control compatibility options. Consult the most
current catalog or pricelist for the latest ordering information.
o(1) 2-gang Decora cover plate cover w/mounting screws

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 5 61 -00033 Rev 01_c
2 – Product eatures
igure 1 – unD6IO-BT Top Panel eatures
1 Bluetooth® pairing/connect button
2 Power/ID/Error indicator (see note below)
3 Bluetooth® status indicator
Stereo RCA Inputs
5 Stereo 3.5mm Input
6 Stereo 3.5mm Output
*Note: The unD6IO-BT is equipped ith error reporting features. Upon po er up, the front panel po er LED ill briefly
light red and then change to green if the device boots successfully. If the LED remains on solid red, this indicates a device
failure. If po er cycling the unit does not correct this problem, contact Attero Tech technical support.
*Note: The unD6IO-BT has a label on the front of the metal housing at the top that sho s the devices MAC address. This
is important for initial device identification as the last six digits make up part of the devices default net ork name that
is sho n hen the device is detected by Dante™ Controller. The full MAC address is also sho n on the back of the unit.

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 6 61 -00033 Rev 01_c
igure 2 – unD6IO-BT Rear Panel eatures
7 Recessed RJ- 5 (Dante™, Control and PoE)
8 Recessed Factory Reset switch

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 7 61 -00033 Rev 01_c
2.1 – Audio Signal low
The following diagram depicts the internal signal flow for the unD6IO-BT.
igure 3 - unD6IO-BT Signal low
Dante™ Channel I/O unction
TX 1 Bluetooth Transmit– L Channel
TX 2 Bluetooth Transmit– R Channel
TX3 RCA L or 3.5mm In L, or sum of both
TX RCA R or 3.5mm In R, or sum of both
RX1 Bluetooth® Receive/3.5mm Out L
RX2 3.5mm Out R
igure 4 - Dante™ Channel Mapping

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 8 61 -00033 Rev 01_c
3 – Mounting and Installation
A typical installation will involve mounting the wall plate into a pre mounted 2-gang or larger wall box, standard drywall
bracket or mud ring. Before starting, make sure the wall box where the unD6IO-BT is to be installed is pre-wired with a
suitable CAT5e or better cable back to a PoE-enabled network switch or mid-span injector. If a mid-span injector is being
used, the cable should be connected to the port that supplies both Ethernet and power (refer to the mid-span injectors
manual if unsure which port is which). The unD6IO-BT packaging includes all of the necessary screws for mounting the
product and the included Decora wall plate.
*Note: All Attero Tech products are tested using UTP cabling and it is recommended that UTP cabling be used hen
installing them. STP cabling can be used for installation though care must be taken not introduce grounding issues into
the system by doing so.
Attach the network cable from the switch/mid-span injector to the Dante™ I/F port of the unD6IO-BT. If the switch or mid-
span injector is already running and PoE is enabled, the unit should power up and the green ID LED on the front of the
device should turn on.
With the cable attached, carefully place the unD6IO-BTinto the wall box taking care to not trap the cabling. Once fully in
place, secure it with the screws provided. Once the unit is secured in the wall box, fit the Decora plate over the front of
the unit and secure it with the screws provided with it. It is recommended to not over-tighten the screws that attach the
included Decora wall plate to prevent cracking it.

unD6IO-BT
User Manual
 Attero Tech LLC 2018 Page 9 61 -00033 Rev 01_c
igure 5 - unD6IO-BT Dimensioned Drawings