Backyard Discovery SCENIC HEIGHTS User manual

Made in China
Features the fastening system.
Save this assembly manual for future reference in the event that
you need to order replacementparts.
•Owner's Manual
•Frequently Asked Questions
•Assembly Instructions
•Warranty Information
SCENIC HEIGHTS
PLAYHOUSE
MODEL: # 1605336

GENERAL SAFETY INSTRUCTIONS
PURPOSE
This product is intended for outdoor, domestic use only. It is not suitable for commercial or medical use.
DANGER FOR CHILDREN
WARNING! No eating while using the product
This product may only be used with adult supervision at all times.
The packaging material is not suitable for children due to choking and suffocation hazards.
RISK OF INJURIES
Do not use the product if it is damaged or defective. If it is damaged or defective, please contact a
qualified technician.
Check the product before each use. Defective parts must be changed immediately as they can impair
the function and the safety of the product.
No more than one person per swing or per attachment.
Use the product only on even and non-slipping surfaces. Never use it near water and keep sufficient
space around for safety.
PRODUCT DAMAGE
Do not make alterations to the product. Only use original spare parts. Qualified technicians should only
carry out repairs –improper repairs can lead to danger for the user. Use this product only as described
in this manual.
Protect the product against splashes, humidity, high temperature and direct sunlight.
ASSEMBLY ADVICE
The assembly of the product must be done carefully and by an able-bodied adult. If in any doubt, ask a
technically qualified person.
Before you start with the assembly, read the instructions carefully.
Remove all packaging materials and lay down all parts on an open space. This gives you an overview
and simplifies the assembly procedure.
Check with the parts list that all parts are available. Dispose of the packaging material when the
assembly is completed.
Beware that when using tools or doing technical work, there is always a risk of injuries. Assemble the
product with care.
Create a danger free environment; for example, do not let tools lay around the workspace. Store the
packaging material in a way that cannot cause any danger.
After installing the product according to the instruction manual, ensure all screws, bolts and nuts are
correctly installed and tightened and that all joints are secure.
Reasonable space must be kept between the product and possible sources of danger, such as other
equipment swimming pools and fences.
The product must be assembled correctly before use.
Place the product on a level surface at least 2 m from any structure or obstruction such as a fence,
garage or house.
No modifications are to be made to the original product.
The product must always be used in a well-lit area.
Do not place anything under the product.
Use gloves during assembly and disassembly.
Outdoor products should be equipped with a device that in strong wind conditions avoid displacement
due to wind (e.g. steel bars in the ground or loads like sand bag or water bags).

In certain areas during winter, snow buildup and the low temperatures can damage the product. It is
recommended to remove snow buildup and to store the product indoor.
We strongly recommend visual inspections every 3 months to insure the integrity of the entire product.
Replace any parts as necessary.
SAFETY INSTRUCTIONS
The safety instructions of the product should always be considered and obeyed.
Using the product may result in permanent injury such as paralysis, or even death. Falling off the
product may lead to injuries, particularly to the back, neck or head.
No clothes with hooks or lose parts should be worn or carried during product usage in order to avoid
hooks getting caught and causing injury.
Moving the product whilst assembled may affect the integrity of the frame. Should it be necessary to
move the product, please consider the following:
1.) Force to be evenly spaced around the frame to lift the product off the ground
2.) The product must be carried horizontally
3.) Use caution whilst moving as it could bend the product frame.
Users should be familiar with the assembly manual. This manual contains assembly guidance; selected
precautionary measures as well as recommendations for servicing and maintenance of the product, in
order to ensure safe and fun usage.
It is the responsibility of the owner or the supervisor to guarantee that all users of the product are
informed sufficiently of all warning references and safety instructions.
For the supervisor:
The supervisor’s role is to make sure users are aware of all safety precautions and that these precautions are
enforced. When a supervisor is not available, the product may be disassembled or covered to limit access.
The product can be only used if it is in good condition, worn or damaged parts should be replaced.
Objects, which could be dangerous to the user, should be away from the product
Avoid unauthorized and unsupervised use of the product.
Do not use the product under influence of alcohol or drugs (incl. medicines).
Do not use the product or its attachments as a jumping platform.

Consumer Information Sheet for Playground Surfacing Materials
The US Consumer Product Safety Commission (CPSC) estimates that about 100 000 playground equipment-
related injuries resulting from falls to the ground surface are treated annually in US hospital emergency rooms.
Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the
potential to be fatal, particularly when the injury is to the head. The surface under and around playground
equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall
on to a shock-absorbing surface is less likely to cause a serious injury than a fall onto a hard surface. Playground
equipment should never be placed on hard surfaces, such as concrete or asphalt, and while grass may appear
to be acceptable, it may quickly turn to hard-packed earth in areas of high traffic. Shredded bark mulch, wood
chips, tine sand or the gravel are considered to be acceptable shock absorbing surfaces when installed and
maintained at a sufficient depth under and around playground equipment.
Table B.1 lists the maximum height from which a child would not be expected to sustain a life-threatening head
injury in a fall on to four different loose-fill surfacing materials if they are Installed and maintained at depths of
150 mm, 225 mm and 300 mm.
Table B.1: Fall height in millimetres from which a life-threatening head injury would not be expected
However, it should be recognised that all injuries due to falls cannot be prevented, no matter what surfacing
material is used.
It is recommended that a shock absorbing material extend a minimum of 1 800 mm in all directions from the
perimeter of stationary equipment such as climbing frames and slides. However, because children may
deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a
swing a minimum distance of twice the height of the pivot point measured from a point directly beneath the pivot
on the supporting structure.
This information is intended to assist in comparing the relative shock-absorbing properties of various materials.
No particular material is recommended over another. However, each material is only effective when properly
maintained. Materials should be checked periodically and replenished to maintain correct depth as determined
necessary for the equipment in question. The choice of a material depends on the type and height of the
playground equipment, the availability of the material in a particular area, and its cost.
Type of Material
Depth of surfacing material
150mm
225mm
300mm
Double Shredded Bark
Mulch
1800
3000
3300
Wood Chips
1800
2100
3600
Fine Sand
1500
1500
2700
Fine Gravel
1800
2100
3000

Play House Assembly Manual FAQs:
1. Does the area for the play house need to be level? Yes. We recommend the play house
be positioned on a at level area for maximum safety and durability. Any stakes provided should be used to
secure it rmly tothe ground.
2. What size area is recommended for the play house? We recommend at least a 6’ (six foot)
perimeter around and above the play house for maximum safety.
3. What age range is appropriate for the play houses? The play houses are recommended for
children ages 2 – 10 years.
4. Is the wood treated with chemicals? Backyard Discovery uses 100% Chinese Cedar wood which is naturally
bug resistant, decay and rot resistant. To help ensure your child’s safety, our wood is completely chemical free
and we do not use pressure-treated wood. The stain we use is a top coat using a water-based product that is
for appearance only.
5. How often should the play house be stained? We recommend the play house be stained
once each year. A water or oil based stain can be used at the customer’s discretion.
6. Why does it seem that my play house is developing cracks? Wood is a natural material; no two pieces are
exactly alike. Each piece has its own characteristics and personality and reacts dierently to climate changes.
When any wood product is exposed to the elements, it develops “wood checks”. A check is the radial
separation of the wood bers running with the grain of the wood. These are caused by the varying temperature
and moisture conditions. A check is not a crack – it does not aect the strength or durability of the wood or
structural integrity of the play house.
7. What is the best way to get started assembling the play house? We recommend taking all
the parts out of the boxes and arranging them by part number before you begin any assembly. This will not
only allow faster assembly, but will also identify any parts that may be missing or damaged so they can be
replaced before assembly.
8. The play house seems to rock or sway too much. What’s wrong? Rocking is caused by uneven ground or
obstructions such as rocks, roots, etc. under the ground rails. These should be removed and the ground
underneath re-leveled to prevent rocking. Also ensure the play house is securely staked to the ground using
any stakes provided.
9. The 2”x4” boards do not measure 2”x 4”. Why not? It is common practice to describe lumber
dimensions using the rough cut sizes from the sawmill and not the nished dimensions. Retailers, home stores,
etc. all use this accepted practice for describing lumber dimensions. However, Backyard Discovery play
houses are designed and constructed using the actual dimensions so everything ts properly and remains so
during the life of the play house.

(Level 24")
(Open End Wrenches 1/2")
(Square)
(Tape Measure)
(3/8" Drive Ratchet, 1/2" STD
Sockets 1/2" Deep Sockets)
(Claw Hammer)
(Cordless Drill or Electric Drill)
(An Adult w/ an Adult Helper)
(Rubber Mallet - Optional)
(Ladder)
(Phillips Screw Driver)
(Drill Attachments:
Phillips Head)
(7/16" Drill Bit)
Tools Required for Installation:
(These are the tools that are generally required for assembly of our outdoor products. These tools
are not included with the outdoor product purchase.)

«
S
P
A
N
I
S
H
SAFE PLAY AREA DIAGRAM
Safe Play Area:
• The safe play area refers to a zone extending 6' beyond the play product on all sides, including the
space above the play product.
• The ground surface must be level. Installing your play product on sloping ground can cause it to
lean or "rack". This leaning puts additional stress on all connections and joints and in time will cause
those connections to loosen and fail.
• The safe play area must be free of all structures, landscaping, trees and branches, rocks, wires,
and other obstacles to safe play. Children can be seriously injured running or swinging into these
obstacles.
• Remove all tripping hazards from the safe play area. Tripping hazards include: roots, stumps, rocks,
landscaping, sprinkler heads, railroad ties, plumbing and electrical connections.
• Play product needs to be installed on solid ground.
General Information:
Your set has been designed and engineered for
children only and for residential use only.
A maximum of 150 lbs. per child is recommended for
play activities designed for individual use.
A maximum of 120 lbs. per child is recommended for
play activities designed for multiple child use.
A maximum of 6 children is recommended for this unit.
Dimensions:
• The Chalet has one layout option.
Layout Ground Dimension Safe Play Area*
6'-4
7
8 " x 6'-4 3 4" x 67
1
4 " Tall 18'-4
7
8 " x 18'-4
3
4 "
*Level Ground Surface - See below
SELECTING THE CORRECT LOCATION FOR YOUR PLAY PRODUCT IS IMPORTANT
FOR YOUR CHILDREN’S SAFETY AND THE PRODUCT’S LONGEVITY
SAFETY AND ASSEMBLY INFORMATION
House
6'-0"
6'-0"
6'-4 7/8"
6'-4 3/4"
18'-4 7/8"
18'-4 3/4"
SAFE PLAY ZONE

2'-10 3/8"
1'-3 3/8"
35°
3'-2 9/16"
1'-6 7/8"
2'-1"
1'-7 7/8" 1'-1 3/4"
4'-8 1/8"
6'-3 1/8"
6'-4 7/8"
2'-7 5/8"
2'-11 5/8"
5'-2 3/8"
7'-7 1/4"
BASIC SETUP DIMENSIONS
FRONT VIEW
6'-4 13/16"

2'- 3/8"
2'-2 3/4"
3'-2 5/8"
1'-1 7/8"
2'-11"
6'-1"
1'-5"
3'-3 1/8"
38.4°
1'-5 3/8"
5'-2 3/8"
7'-7 1/4"
BASIC SETUP DIMENSIONS
RIGHT SIDE VIEW
6'-4 13/16"

5 7/8"
7 1/2"
38°
24 3/8"
35"
62 3/8"
19 1/8"
21 3/4"
91 1/4"
48 1/8"
26 3/8"
BASIC SETUP DIMENSIONS
LEFT SIDE VIEW

Parts Identification
Wood Components
(NOT TO SCALE)
E1 - LEFT FRONT UPRIGHT - W4L06667
1 3/8"x3 3/8"x62 3/8" (36x86x1584)
(1)
E2 - RIGHT FRONT UPRIGHT - W4L06666
1 3/8"x3 3/8"x62 3/8" (36x86x1584)
(1)
E3 - RIGHT REAR UPRIGHT - W4L06648
13/8"x3 3/8"x62 3/8" (36x86x1584)
(1)
E4 - LEFT REAR UPRIGHT - W4L06388
1 3/8"x3 3/8"x35" (36x86x889)
(1)
E5 - RIGHT CENTER UPRIGHT - W4L06644
1 3/8"x3 3/8"x36 1/4" (36x86x920)
(1)
E6 - RIGHT REAR UPRIGHT - W4L06651
1 3/8"x3 3/8"x62 3/8" (36x86x1584)
(1)
E7 - HANDRAIL BLOCK - W4L06678
1 3/8"x3 3/8"x1" (36x86x26)
(1)
F1 - STAIRCASE POST - W4L06662
13/8"x2 3/8"x33 3/4" (36x60x858)
(1)
G1 - STAIRCASE BOARD - W4L06657
1"x5 1/4"x20 3/8" (24x134x518)
(1)
H1 - FLOOR RAIL - W4L06391
1"x3 3/8"x56 3/4" (24x86x1442)
(1)
H2 - FLOOR RAIL - W4L06392
1"x3 3/8"x54 7/8" (24x86x1394)
(1)
H3 - FLOOR RAIL - W4L06646
1"x3 3/8"x75 3/4" (24x86x1924)
(1)
H4 - FLOOR RAIL - W4L06645
1"x3 3/8"x54 7/8" (24x86x1394)
(1)
H5 - FLOOR SUPPORT - W4L06399
1"x3 3/8"x54 7/8" (24x86x1394)
(2)

Parts Identification
Wood Components
(NOT TO SCALE)
H6 - FLOOR RAIL - W4L06654
1"x3 3/8"x16 3/8" (24x86x416)
(1)
H7 - FLOOR RAIL - W4L06655
1"x3 3/8"x19" (24x86x482)
(1)
H8 - STAIR HAND RAIL - W4L06663
1"x3 3/8"x54" (24x86x1372)
(1)
H14 - STAIR HAND RAIL - W4L06679
1"x3 3/8"x47 3/8" (24x86x1204)
(1)
H20 - DECK BRACE - W4L06397
1"x3 3/8"x13" (24x86x330)
(6)
H76 - LADDER RUNG - W4L06609
1"x3 3/8"x18 1/8" (24x86x460)
(3)
H79 - LEFT UPRIGHT - W4L06611
1"x3 3/8"x38 3/8" (24x86x976)
(1)
H80 - RIGHT UPRIGHT - W4L06612
1"x3 3/8"x38 3/8" (24x86x976)
(1)
J1 - FLOOR SUPPORT BLOCK - W4L06403
1"x2 3/8"x3 3/8" (24x60x86)
(3)
J2 - COUNTER TOP SUPPORT - W4L06411
1"x2 3/8"x5 7/8" (24x60x150)
(1)
J3 - SEAT SUPPORT - W4L06417
1"x2 3/8"x8 3/8" (24x60x214)
(2)
K1 - GROUND BOARD - W4L06389
5/8"x5 1/4"x54 7/8" (16x134x1394)
(1)
K2 - GROUND BOARD - W4L06390
5/8"x5 1/4"x56 1/8" (16x134x1426)
(1)
K3 - GROUND BOARD - W4L06649
5/8"x5 1/4"x55 1/2" (16x134x1410)
(1)

Parts Identification
Wood Components
(NOT TO SCALE)
K4 - GROUND BOARD - W4L06650
5/8"x5 1/4"x73 7/8" (16x134x1876)
(1)
K5 - GROUND BOARD - W4L06652
5/8"x5 1/4"x55" (16x134x1397)
(1)
K6 - STAIR BOARD - W4L06674
5/8"x5 1/4"x16 7/8" (16x134x430)
(4)
L1 - FLOOR BOARD - W4L06400
5/8"x4 3/8"x52" (16x112x1321)
(1)
L2 - FLOOR BOARD - W4L06658
5/8"x4 3/8"x73 3/8" (16x112x1864)
(1)
L3 - GABLE BOARD - W4L06412
5/8"x4 3/8"x25 3/8" (16x112x644)
(4)
L4 - BOTTOM BOARD - W4L06420
5/8"x4 3/8"x15" (16x112x380)
(4)
L5 - LONG SIDE BOARD - W4L06421
5/8"x4 3/8"x15" (16x112x380)
(6)
L6 - SHORT SIDE BOARD - W4L06422
5/8"x4 3/8"x7 1/2" (16x112x192)
(8)
L7 - ARCHED SIDE BOARD - W4L06423
5/8"x4 3/8"x15" (16x112x380)
(2)
L8 - SEAT BOARD - W4L06418
1"x4 3/8"x36 3/4" (24x112x934)
(2)
M1 - GROWTH BOARD - W4L06690
5/8"x3 3/8"x60 1/4" (16x86x1530)
(1)

Parts Identification
Wood Components
(NOT TO SCALE)
M2 - WALL RAIL - W4L06393
5/8"x3 3/8"x17 1/2" (16x86x445)
(2)
M3 - WALL RAIL - W4L06394
5/8"x3 3/8"x54 7/8" (16x86x1394)
(1)
M4 - FLOOR BOARD - W4L06401
5/8"x3 3/8"x56 3/4" (16x86x1442)
(9)
M5 - FLOOR BOARD - W4L06402
5/8"x3 3/8"x54 3/8" (16x86x1382)
(1)
M6 - WALL BOARD - W4L06668
5/8"x3 3/8"x26 3/4" (16x86x679)
(2)
M7 - WALL RAIL - W4L06643
5/8"x3 3/8"x38 1/4" (16x86x970)
(2)
M8 - WALL RAIL - W4L06409
5/8"x3 3/8"x17 1/4" (16x86x439)
(2)
M9 - WALL RAIL - W4L06647
5/8"x3 3/8"x36 3/8" (16x86x924)
(2)
M10 - COUNTER TOP - W4L06413
5/8"x3 3/8"x23 5/8" (16x86x600)
(2)
M11 - FILLER BOARD - W4L06656
5/8"x3 3/8"x5 1/2" (16x86x139)
(1)
M12 - FLOOR BOARD - W4L06659
5/8"x3 3/8"x75 3/4" (16x86x1924)
(2)
M13 - FLOOR BOARD - W4L06660
5/8"x3 3/8"x75 3/4" (16x86x1924)
(1)
M14 - FLOOR BOARD - W4L06661
5/8"x3 3/8"x73 3/8" (16x86x1863)
(1)
M15 - STAIR BOARD - W4L06675
5/8"x3"x16 7/8" (16x75x430)
(2)

Parts Identification
Wood Components
(NOT TO SCALE)
M16 - WALL RAIL - W4L06653
5/8"x3 3/8"x16 3/8" (16x86x416)
(2)
M73 - REAR SUPPORT - W4L06608
5/8"x3 3/8"x19 1/4" (16x86x488)
(1)
M110 - ATTACHMENT BOARD - W4L06610
5/8"x3 3/8"x19 1/4" (16x86x488)
(1)
N1 - TIE STRAP - W4L05043
5/8”x2”x3 1/8” (16x50x80)
(8)
N2 - REAR WINDOW SHELF - W4L06414
5/8"x2 3/8"x18 7/8" (16x60x479)
(1)
N3 - LEFT WINDOW SHELF - W4L06415
5/8"x2 3/8"x19 1/8" (16x60x485)
(1)
N4 - SEAT CLEAT - W4L06419
5/8"x2 3/8"x9" (16x60x230)
(1)
O1 - PICKET - W4L06665
5/8"x1 3/8"x20 1/2" (16x34x520)
(28)
O2 - PICKET - W4L06676
5/8"x1 3/8"x29 1/2" (16x34x750)
(9)
Q1 - COUNTER TOP SUPPORT - W4L06416
1"x4 3/8"x5 7/8" (24x112x150)
(1)
S2 - CORNER BOARD - W4L06424
1"x1"x8 7/8" (24x24x224)
(8)
S1 - RAIL BOARD - W4L06664
1"x1"x26 3/4" (24x24x679)
(2)
W1 - HANDRAIL BLOCK - W4L06677
2"x3 3/8"x3 3/8" (50x86x86)
(1)
Y1 - STAIR BOARD - W4L06669
5/8"x4"x16 7/8" (16x102x430)
(10)
M33 - FASCIA BOARD - W4L06559
5/8"x3 3/8"x25 5/8" (16x86x652)
(4)

Parts Identification
Wood Components
(NOT TO SCALE)
(1) WP1 - FRONT RIGHT CORNER PANEL - W2A01911 (1) WP2 - REAR RIGHT CORNER PANEL - W2A01914
(1) WP3 - FRONT LEFT CORNER PANEL - W2A01917 (1) WP4 - REAR LEFT CORNER PANEL - W2A01920
(1) WP5 - REAR CENTER PANEL - W2A01922 (1) WP6 - LEFT CENTER PANEL - W2A01924

Parts Identification
Wood Components
(NOT TO SCALE)
(2) WP8 - HEADER ASSEMBLY - W2A01926 (2) SR1 - STAIR STRINGER ASSEMBLY - W2A01940
(2) RP1 - LOWER ROOF PANEL - W2A01929 (2) RP2 - UPPER ROOF PANEL - W2A01930
(1) DP2 - LEFT DOOR ASSEMBLY - W2A01928 (1) DP1 - RIGHT DOOR ASSEMBLY - W2A01927

Parts Identification
Hardware
- BOLT WH 1/4x1 BLK - H100171
(9)
VY - BOLT WH 5/16x2-1/4 BLK - H100205
(8)
- BOLT WH 5/16x1 3/4 BLK - H100378
(7)
- BOLT WH 5/16x1/2 BLK - H100396
(6)
- BOLT WH 1/4x1/2 BLK - H100401
(4)
- BOLT WH 5/16x1 1/2 BLK - H100407
(2)
- BOLT WH 5/16x1 1/4 BLK - H100459
(4)
- BOLT WH 5/16x1 BLK - H100468
(1)
VN - BOLT WH 5/16x2-3/4 BLK - H100195
(7)
P - BOLT WH 5/16x3 BLK - H100416
(1)
- BOLT WH 5/16x4 1/4 BLK - H100513
(1)
VK - NUT BARREL WH 5/16x7/8 BLK - H100192
(1)
- NUT BARREL WH 1/4x7/8 BLK - H100399
(4)
- NUT BARREL WH 1/4x5/8 BLK - H100404
(4)
- T-NUT 5/16 BLK - H100379
(47)
- T-NUT 1/4 BLK - H100398
(4)
- NUT BARREL WH 5/16x5/8 BLK - H100469
(4)
- BOLT WH 5/16x2 BLK - H100457
(19)

Parts Identification
Hardware
BC - SCREW PWH 8x3/4 - H100070
(9)
BN - SCREW PFH 8x1 - H100085
(22)
BP - SCREW PFH 8x1 1/2 - H100086
(99)
BQ - SCREW PFH 8x1 1/4 - H100087
(142)
BR - SCREW PFH 8x1 1/8 - H100088
(160)
BS - SCREW PFH 8x1 3/4 - H100089
(11)
BT - SCREW PFH 8x2 1/2 - H100090
(17)
BV - SCREW PFH 8x2 1/4 - H100091
(7)
CK - SCREW PFH 8x2 - H100111
(22)
CY - SCREW PWH 8x5/8 - H100128
(4)
VT - SCREW PFH 8x1-1/2 BLK - H100200
(4)
VV - SCREW PWH 8x5/8 BLK - H100202
(15)
- SCREW PFH 8x1 1/4 BLK - H100387
(9)
LC - LAG SCREW WH 1/4x1-1/2 BLK - H100403
(7)
- SCREW PWH 8x1/2 BLK - H100408
(9)
- LAG SCREW WH 5/16x2 BLK - H100458
(18)
- LAG SCREW WH 5/16x1 1/2 BLK - H100471
(15)
- T-30 TORX WRENCH - H100114
(2)
- T-40 TORX BIT - A100042
(2) - T-30 TORX BIT - H100147 (2)
- T-40 TORX WRENCH - A100041
(2)
VS - WASHER LOCK EXT 12x19 BLK - H100199
(6)
VR - WASHER LOCK EXT 8x19 BLK - H100198
(78)
- WASHER LOCK EXT 8x15 BLK - H100400
(9)
- WASHER LOCK EXT 6x15 BLK - H100405
(15)

Parts Identification
Accessories
(NOT TO SCALE)
EA - HAND GRIP YELLOW PLASTIC - A100043
(2)
SQ - "A" REVISION TAG - A100314
(1) - 90°L-BRACKET - BLK - A4M00555
(12) (2) - SALOON DOOR HINGE KIT - A4M00642
VB - PLASTIC SUNBURST - A100361
(2)
- GROUND STAKE REBAR - A4M00527
(4)
- BYD ID TAG (MEDIUM) AGES 2 TO 10 - A4M00528
(1)
- L BRACKET 2.5x38x50x55 - A4M00615
(1)
- FAUCET KIT - A6P00024
(1) - STOVE KIT - A6P00025
(1) - SURFACE MOUNT BASIN - A6P00032
(1)
- SEAT CUSHION - A6P00107
(1)