Bauknecht GKEA 2909 Dimensions

D F NL E P GR DK
S N FIN
I
GB
PRODUCT SHEET GB
5019 603 33004
1. Compartment for freezing
2. Control unit
3. Area for drawers and pull-out baskets
4. Defrost water drain channel
5. Rating plate (inside the appliance).
Note: the design of drawers and accessories may vary, depending on the model.
Controls
ADigital temperature display.
BFreezer on/off button.
CFast freeze button.
DYellow LED: indicates that the fast freeze
function is in operation.
EAcoustic alarm mute button.
FRed LED: flashes to indicate that the
temperature in the freezer compartment is
too high.
GYellow led: control panel locked.
HIndicator lights: when illuminated, they
indicate that the appliance is operating to
lower (a) or to increase (b) the internal
temperature after settings have been
changed.
IAdjustment buttons - (a) for lowering, (b) for
increasing - the internal temperature.
JButton for locking the control panel.
Switching on
1
2
3
4
5
storage compartment
freezer compartment
1. Plug in the appliance
Important
If the digital display shows only an
illuminated dot, press the freezer
on/off button B.
Six horizontal lines appear on the
digital display.
After about 3 seconds, when the
appliance is warm, (internal
temperature above 10°C) only the
two lines in the middle remain
illuminated;redledFilluminatesand
the acoustic alarm sounds.
2. Press button E to mute the
acoustic alarm. The acoustic alarm stops while the red led continues to flash.
3. Wait until the temperature
indicated on the digital display
reaches -12°C.
When the temperature reaches
-12°C, the red led automatically
stops flashing.
4. Place food to be frozen and/or
already frozen food in the freezer.
6Gb33004.fm5 Page 1 Thursday, January 25, 2001 4:32 PM

5019 603 33004 D F NL E P GR DK
S N FIN
IGB
Freezer compartment temperature adjustment
The appliance is normally factory set to operate at the recommended temperature of -18°C.
To alter the internal temperature between -16°C and -24°C, proceed as follows:
•Press button I/a or I/b once to adjust the internal temperature: the digital display shows the
temperature previously set.
•Each time the button is pressed, the temperature setting is changed by 1°C: the value (between
-16°C and -24°C) flashes on the display.
•Approximately 5 seconds after the button has been pressed for the last time, the set temperature
is stored, the display stops flashing and the current internal temperature is shown on the display.
Note:
The digital display shows internal temperature values between +10°C and -24°C.
In the event of a power failure, selected functions remain stored in the memory.
Fast freezing
The fast freeze function is automatically deactivated after 48 hours.
Alarm signals
Note:
The temperature alarm may activate if the door is left open for a prolonged period of time or following
the introduction of fresh food in the freezer compartment; this temporary rise in temperature does not
affect the storage of already frozen food in any way.
Defrosting
Control panel lock function
This function prevents anyone inadvertently altering operating parameters or switching the appliance
off. To lock the control panel: press button J and then button B and hold down for about 5 seconds,
until the yellow led Glights up. To unlock the control panel, press the same buttons again until the
yellow led G switches off.
Signal Cause Solution
Door open alarm The acoustic alarm is
activated The door has been left open for more than 1 minute Close the door
Temperature
alarm The acoustic alarm and red
led F are activated The internal temperature is above -12°C Press button E; wait for the temperature to fall
below -12°C again
Temperature
sensor alarm The acoustic alarm is
activated and the display
shows “SF”
Temperature sensor fault Contact After-sales
service
Prolonged power
failure alarm The acoustic alarm and red
led Fare activated; the
display flashes, indicating
the highest temperature
reached following the
power failure.
Prolonged lack of power
supply, causing the internal
temperature to rise to very
high values at which correct
food storage cannot be
guaranteed
Press button E; the
display now indicates
the current internal
temperture.
1. Press the freezer on/off button BAn illuminated dot appears on the digital
display
2. Unplug the appliance or switch off at the
main switch
3. Follow the instructions given in the
instructions booklet
4. Plug in the appliance once again
5. Press the freezer on/off button B. Follow the steps detailed in “Switching on the
appliance”
6Gb33004.fm5 Page 2 Thursday, January 25, 2001 4:32 PM