BeaverLAB TW1 User manual

DDL-TW1/Pro/Max Instruction ManualIntelligentAstronomical Telescope TW1Special Reminder:Do not observe the sun directly when not wearing "Bud film sunglasses".Otherwise, the image sensor will burn out.Image Collector: WIFI Password: 12345678Please read this manual carefully before using the product!Please keep the instruction manual properly!

1.Product Overview2.Instructions For Use3.Installation Instructions4.Usage Procedure5.Accessories And Tools6.The Fault Is Rectified7. Trademarks And Legal Statements8.Overall Parameters0103040816171819Directory

Thank you for purchasing Intelligent Astronomical Telescope.Please read this manual carefully before use and keep it properly. Do not use the telescope withoutknowing how to use it In order to avoid unnecessary loss caused by wrong use.Description of telescope compositionDust coverThe primarymirrorholderLocking knobThe tripodThe focuser knobsPitch locking handleImageacquisition unitFind the star mirrorQuick releasescrew rod0101 Product Overview

02Description of telescope knobsStarfinder red dot left andright fine-tuning knobStarfinder red dot up anddown fine-tuning knobFine tune the red dotclockwise to the leftFine tune the red dotcounterclockwise to the rightFine tune the red dot clockwise upwardsbackwards Needle down to fine tune the red dotStarfinder red dot switchBrightness trim knobFine tune the red dot to lightenreverse time clockwise Needlefine tuning red dots to darkencloseStar finder fixed locking knobLock the star finder clockwisecounterclockwise Release the starfinderTilt lock handleLock pitch clockwiseloosen counterclockwise Open, can be bent through the grip Their operations.

03Lock knob in horizontal direction of gimbalFocal length adjustment knobClockwise lock for horizontal turncounterclockwise release.The rack at the bottom of the focusing seat is coatedwith grease. Do not touch it.02 Usage InstructionsProtect the lens of the objective lens and close the dust cover after use to avoid dust or foreign objects.Pay attention to protect the image collector. Please put the protective cover on after use to avoid dust or foreign matter.The telescope is suspended from the side, without heavy weight.When you do not use this product, please lock the various institutions of the gimbal to avoid the rotation of the astronomical telescope under the action of gravity.Please use in the environment of -10℃-45℃.This product is not waterproof, please avoid getting wet by any liquid.Keep away from fire and heat sources.Please keep dust out of the lens.This product is a precision instrument, please avoid collision and violent vibration.In the case of low temperature, the available capacity of the battery will have different degrees of decay, this is the characteristics of lithium batteries, is a normal phenomenon.In case of any abnormal phenomenon, please refer to the troubleshooting manual in time. In case of any unsolvable fault, please refer to the after-sales instructions.Disassembling telescopes without permission is not covered by the warranty policy and may result in irreparable damage.

After receiving the product, users are required to complete the overall assembly of the product bythemselves.Install the tripod1. Take out the tripod, loosen the fastening knob of the tripod, and pull out each leg to a uniform length.2. Flatten the folded structure in the middle of the tripod.Special WarningDo not directly observe the sun without properly installed Bader film sunglasses. This will cause theimage collector chip to burn.Minors should be accompanied by an adult.Private modification of the telescope is prohibited.When the telescope is not in use, please cover the dustproof cover to keep the machine clean.0403 Installation InstructionsProtect the lens of the objective lens and close the dust cover after use to avoid dust or foreign objects.Pay attention to protect the image collector. Please put the protective cover on after use to avoid dust or foreign matter.The telescope is suspended from the side, without heavy weight.When you do not use this product, please lock the various institutions of the gimbal to avoid the rotation of the astronomical telescope under the action of gravity.Please use in the environment of -10℃-45℃.This product is not waterproof, please avoid getting wet by any liquid.Keep away from fire and heat sources.Please keep dust out of the lens.This product is a precision instrument, please avoid collision and violent vibration.In the case of low temperature, the available capacity of the battery will have different degrees of decay, this is the characteristics of lithium batteries, is a normal phenomenon.In case of any abnormal phenomenon, please refer to the troubleshooting manual in time. In case of any unsolvable fault, please refer to the after-sales instructions.Disassembling telescopes without permission is not covered by the warranty policy and may result in irreparable damage.

05Install primary mirror barrel with tripod1. Prepare the main mirror, the whole head, the tripod, and the quick detachable rod, as shown below.2. Take out the main mirror and the cradle head, and align the three positioning pins of the cradle head base with the corresponding three holes on the tripod.3. Insert the quick disconnecting rod into the hole at the bottom of the tripod and tighten it clockwise. During the removal, it is necessary to hold the head of the gimbal and the mirror barrel by hand while loosening the quick detachable rod to prevent falling.HolderThe tripodQuick releasescrew rod

06Installation of image collector1. Get the image collector ready.2. Align the locking clip on the side of the image collector with the notch of the telescopic cylinder andinsert it, and then rotate the image collector to align the mark point to fix and jam.② Insert the image collector① Take off the dust cover③ Rotate clockwise to thelocking positionInstall the star finder1. Prepare the star finder and align the star finder with the support port. Note the gap in the port.2. Tighten the fixing knob of the star finder.Tip: Pay attention to the installation direction of the star finder.① Insert the star finder into the support interface② Tighten the fixing knob of the star finderPay attention to thebayonet position

07Replace the battery1. Take out the star finder, place the battery in the interface where the star finder is inserted into the support, and remove the battery holder with your fingers or tweezers.2. The star finder uses CR-2032 battery. When replacing the button battery, pay attention to the positive and negative terminals of the battery.Calibrate the red dot star finder1. Find a target more than 100 meters away with your naked eye.2. Adjust the primary mirror of the telescope to find the target as a whole and move to the center of the field of view.3. Turn on the star finder red dot switch and turn on the light.4. Find the red dot inside the circular observation mouth at the back of the star finder.5. Adjust the position of the red dot through the knob next to the star finder mirror. The whole assemblyis not finished until the red dot coincides with the target and the calibration is completed.Tip: After the observation, please turn off the red dot of the finderscope.①Take out the battery holder together(Be careful to loosen the locking knob)②Replace the battery,Pay attention tothe positive and negative electrodes③Put the battery holder back, payattention to the direction and position

0804 User ProcedureThe tripod is placed smoothlyRemove the dust coverThe middle triangle isstretched flat and tightThe tripod extension legis opened and locked

Through the focal length adjustment knob can focus the image, so thatthe image is more clearThrough the focusing knob,the image is focused09Release the gimbal locking knob and pitch locking armrest to confirm the observation target.Loosen the gimballocking knobPitch lockthe handrailPitch steering adjustmentHorizontal steering regulation

10Image collector interface and switch instructions:Use of image collector:Orientation calibrationtype-C Indicates the datatransmission interfaceImage collector switch buttonImage collector indicator lightWhen installing the image collector, align thelocking position with the image collectorThe scale can be used to confirm whether thecard is tight.Image and video transmission: Connect to acomputer or pad and open the software towatch relevant images and videos in real time.Charging: When the image collector is short ofpower, the light ring will turn to red flash.At this time, please connect the adapterthrough the Type-C charging cable for charging.The red light will be on when fully charged. When there is a crash, you can press thereset key through small objects, restart theboot again.Reset buttonBlue light breathing: wifi is not connected in wifi mode.The machine is in standby state and automatically shuts down after 3 minutes without operation.Blinking blue: The usb port is not connected.Blue light is on: the machine is normally connected.Blinking red: Power is low. Please charge in time.Red breathing light: charging status.Steady red: The battery is fully charged.On and off machine: long press for 2 seconds to switch on and off machine.Mode switch: Double-click to switch between wifi mode and USB connection mode.This product is equipped with an image collectorSupport wireless observation, and wired observation (users need to be equipped with OTG adapter, Apple system can not be wired connection.

11Charging instructionsMobile phone wireless connectionWhen charging, it is a red breathing light, and whenfully charged, it turns into a long red light.type-C Charging port12hThe image collector can becharged using a 5V1A charger.Do not charge the battery for more than12 hours to avoid affecting the battery life.APP download and installation:1. The image collector should be fully charged before use. If the observation time needs to be extended, it can also be equipped with charging devices such as mobile charging bank to charge in time during the observation.2. Scan the QR code below to download the APP (search "Beaver Point" in App store or Google Play todownload the APP)Scan here to download APP
Android iOS

WIFI password for image collector: 12345678123. Long press the image collector for 2 seconds to start the device, and then it will be in standby state (the blue light is breathing at this time). Open the APP of the mobile phone, select Add Device → selectthe wifi name corresponding to the astronomical telescope (such as DL-TW1-XXXX), and connect→Click Enter after it shows that it has been connected.4. Open the home page and click Start observation to enter the real-time transmission screen.

135. In the process of observation, images can be obtained by taking photos and videotaping. Click belowthe pictures to download and save them in the system album.6. The exposure, sharpening, contrast, saturation and other parameters of the image can also be adjustedin real time through the App to achieve the optimal overall effect.7. Click Astronomy Science on the home page to learn about the eight planets and main constellations ofthe solar system.① Double-click the switch on the image collector to switch the default wifi mode to wired connection mode.Mobile phone, pad and other wired connectionWhen connecting the USB data cable to the mobile phone (pad), the OTG head must be connected to the mobile phone (pad) end.② Connect the device to the image collector through USB data cable.

③ Open the APP and click "Start Observation".In the pop-up "Allow the app Beaver Point to access the USBdevice Dialog box, click OK.①Double-click the switch of the image collector to switch the default wifi mode to wired connection mode.②Connect the computer to the image collector through USB data cable.Wired computer connection14Connect the USB cable to the computer

Pay attention to the cable connection1. IPhone and pad do not support wired connection.2. Mobile phone and pad users need to purchase OTG adapters.3. Before use, the wireless mode of the image collector needs to be converted to the wired mode, and the mode switch can be realized by double-clicking the switch button.4. In wired mode, the image collector will enter the automatic charging mode.③ Open the Windows software and select the device to observe.15Computer users can download the Windows version of thesoftware to's official website (www.beaverlabtech.com or www.dangdangli.com)

16SensorOptical TubeScience BookCableFinder ScopePhone Holder05 Accessories And ToolsAstronomical observationsGuide to Lunar Observation1. Connection: On a clear and moonlit night, check the device to ensure sufficient power of the device. Connect the device through mobile phone to realize real-time image transmission.2. Moon search: open the switch knob of the red dot star search mirror, and find the red dot, find the moon through the star search mirror, and overlap the red dot with the moon target center by turning the head.3. Moonwatching: Use the focus knob until the image is clear. If you need to observe other stars, you can use star finder software or manual astrolabes to find them.The telescope is equipped with a compass, combined with the gift of astrofinder, you can confirmthe current map of the sky, and compare the map to find specific stars or nebulae for observation.See the Astrolabe manual for specific usage
H
e
l
l
o
!
u
n
i
v
e
r
s
e
It's been 13.8 billion years since the Big Bang. In the long river of time, countless stars were born. Stars grow in the expansion of the universe and die in the expansion of the universe. The earth is but a drop in the ocean of stars. Man should keep his eyes on the world, focus on the stars, and set sail for the sea of stars.⸺Thomas Chen
Beaver Culture Innovation Honors production
Beaver Culture Innovation Honors production
BEAVERLAB
Not for sale
PlanisphereTripodSolar FilterCarry Bag

17ReasonThe battery is dead.The charging port isnot securely insertedNo power accessEquipment failureProcessing methodReplace the batteryRemove and reinsert the interfacePut through power supplySend to repairPhenomenon of the problemThe starfinder's reddot is not brightThe device cannot be chargedThere is a power shortagein the image collectorImage collector watershort circuitThe image collector crashedThe ambient temperaturechanges rapidly, causing thelens to fogImage collector lens filter is dirtyDamage caused by external useCrashTimely chargingSend to repairPress the reset button once to resetAt a constant temperature,Use it after the fog clearsWipe the filter with a cottonswab dipped in alcoholMan-made damage isnot covered by the warrantyPress the reset button once to resetThe image collector devicecannot be used normallyImage fuzzyFall、impact to cause theshell broken、 crackThe product can not be shutdown or the key failure06 Telescope Faults And Troubleshooting Methods