BeeControls iBeeSwitch iBKSW-BEE YZZ Series User manual

[e-mail] I www.bee-solutions.tech
By Arrow Engineering –Bulgaria LTD @2020
KNX SMART BUILDINGS & AUTOMATION SOLUTIONS 1
iBKSW-BEE-XYZZ iBeeSwitch
KNX SWITCH
DESCRIPTION
↗
BeeControls’ iBeeSwitch is a wall-
mounting room controller device
with integrated temperature and
humidity sensor.
iBeeSwitch allows to control heating and cooling operating
modes with 2-points, Continuous and PWM thermostat
functions. Each push buttons equipped with an RGB LED to
show feedbacks or visualization and LCD models equipped
with VA-Display technology which provides low energy cost
and good view angle. Moreover, there is a blue navigation
LED for orientation nightlight.
The device provides adjustable LCD backlight and LEDs
intensity for user comfort. Product range has 9 different
models with LCD and without LCD. All models can be
programmable with same ETS database which provides
efficient commissioning.
The device has 2 different parts which are BCU and
Application Board. Downloaded firmware carried on
Application part, BCU part only carries KNX communication
and power generation.
SAFETY INSTRUCTIONS
↗The device should only be installed and put into operation by qualified
electrician or authorized person.
↗Failure to observe the instructions may cause damage to the device
and result in fire and other hazards
↗Do not connect the main voltage (230 VAC) or any other external
voltages to any point of the KNX bus.
↗Ensure that there is enough insulation and space between the 230
VAC voltage cables and KNX bus.
↗Installation only in dry locations and on a 35 mm DIN rail (35 mm) and
do not expose this device to direct sunlight, rain or high humidity.
↗Do not use aerosol sprays, solvents or abrasives that might damage
the device.
MAIN FUNCTIONAL CHARACTERISTICS
↗Pushbutton has Switching, toggle, dimming, shutter/blinds,
thermostat controls, scenes, value, 2 channels, step switching
mode features.
↗Locking feature available for each button and complete
device.
↗On/Off (2-points) and Proportional (Continuous or PWM)
thermostat functions.
↗Comfort, standby, economy and building protection
operating modes.
↗Manual or Automatic switching between Heat and Cool
modes.
↗Temperature measuring through integrated sensor with
possibility of sending the value on change and periodically to
the bus.
↗Temperature (measured, external, setpoint, outdoor values
as ºC or ºF), CO2 Concentration (from bus), humidity operating
modes, fan levels, on/off indicator, warnings and locking status
are displayed on LCDs.
↗Fan controller available with up to 5-speeds.
↗All models can be programmable with same database.
↗Relative humidity measuring through the integrated sensor
with possibility of sending the value on the bus.
↗Threshold alarm define for temperature and humidity levels
DIMENSIONS (mm)

[e-mail] I www.bee-solutions.tech
By Arrow Engineering –Bulgaria LTD @2020
KNX SWITCH –IBKSWBEE-XYZZ 2
MODELS WITH LCD:
MODELS WITHOUT LCD:
iBKSWB01-0YZZ
1
1
Blind
2
2
iBKSWB02-0YZZ
1
Blind
2
3
4
iBKSW304-0YZZ
1
2
3
4
5
6
iBKSWB06-0YZZ
1
Blind
2
3
4
5
6
7
8
iBKSWB08-0YZZ
1
9
2
3
4
5
10
6
7
8
iBKSWB10-0YZZ
Coding standard:
Material and Color Options:
CONFIGURATION:
The assignment of the physical addresses as well as the
parameterization is carried out with KNX Tool (ETS).
1
1
Display
2
2
iBKSWB02-1YZZ
1
Display
2
3
AS3
4
iBKSWB04-1YZZ
1
Display
2
3
4
5
6
7
8
iBKSWB08-1YZZ
iBKSW-B EE X Y ZZ
A B C D E
A : iBeeSwitch group
B : Button count
C : LCD is available or not
D : Material
E : Color
Materials
0: Plastic
1: Aluminum
2: stainless
steal
3: Glass
Colors
01: Black
0: Natural
00: Natural
01: Black
02: Glossy White
1: Black
02: White
03: Matt White
06: Champagne
04: Anthracite Matt
05: Metallic Gray
LCD DISPLAY:
↗LCD display is located between the gangs. The symbols on
LCD display are explained below. LCD backlight can be
automatically switch down while not using the device or
changeable from the bus. Temperature values, humidity and CO2
values can be switch between them with defined time to see all
different values in LCD. Also there are 2 buttons located on up
and down of the frame of LCD display.
↗Each button has 2 different pushbutton functions which are under
short press and long press events. Functions are On, Off, Toggle, Step
Value Switching, Setpoint Control and Operating Mode Switcher. All
thermostat functions can be controllable over LCD buttons. So,
pushbuttons can be arranged for other controls.
CONNECTION TO KNX BUS & PROGRAMMING:
The connection of the KNX bus line is made with the terminal block
(black/red) included in delivery and inserted into the slot of housing.
After pressing the buttons on the top left and bottom left corner of the
device simultaneously, the programming LED is activated by pressing the
button in the bottom right corner and LED’s red light is on. Also, this can
be done by pressing the programming button as another method, In the
circumstances, the device is ready for programming.
1
1

[e-mail] I www.bee-solutions.tech
By Arrow Engineering –Bulgaria LTD @2020
KNX SWITCH –IBKSWBEE-XYZZ 3
MOUNTING:
iBeeSwitch’s mounting steps are described below. The procedures are described in 2 main sections: Mounting of BCU and Mounting of Application board.
Mounting the BCU
The device is suitable for use in dry interior rooms and can only mounted on
a standard sized round or square wall flush mounting box. The BCU should
be mounted after the wall painting process is finished. Otherwise, the
product's cosmetics may be damaged. The mounting steps are shownbelow.
1. The wall flush mounting box installation whether is done
properly should be checked.
2. iBeeSwitch’s BCU part is placed to wall flush mounting box
considering the “TOP” writing which is located on the upper
side of the BCU must be demonstrated up direction.
3. The screws are guided through number “1” and number “2”
holes that are shown above.
4. The BCU should be aligned by scales that is positioned
decently, then tighten the guided screws.
Mounting of the Application Board:
After a successful BCU mounting, iBeeSwitch’s Application Board must
be mounted on the BCU part. The mounting steps are described below.
Communication connector on the Application board that will be
attached to the BCU part.
When connection is succeeded, Application board is ready to be
connected and it must be slightly approached to BCU.
Application Board should be held at an angle of approximately 45
degrees, after that its top side notches must be inserted to BCU top
hidden mounting clips.
Lower side notches should be gently seated in the slot of the BCU
side.
INTERNAL COMPONENT:

[e-mail] I www.bee-solutions.tech
By Arrow Engineering –Bulgaria LTD @2020
KNX SWITCH –IBKSWBEE-XYZZ 4
TECHNICAL DATA:
Model without LCD
Item
No
Part Name
Description
Qty.
1
Front Cover
ABS-PC Front cover
1
2
Main Board
Hardware depends on models
1
3
Screw
M2x4 (mm)
4
4
Button
Mechanism
ABS-PC button mechanism
8
5
Button Cover
Depends on the material
selection
8
6
Button
Mechanism
ABS-PC button mechanism
2
7
Button Cover
Depends on the material
selection
2
8
Front Diffuser
LED diffuser
2
9
Sensor & LED
Temperature & humidity
sensor, navigation &
programming LED
1
10
Screw
M2x4 (mm)
2
11
BCU
Common for all models
1
Model with LCD
Item
No
Part Name
Description
Qty.
1
Front Cover
ABS-PC Front cover
1
2
Main Board
Hardware depends on models
1
3
Screw
M2x4 (mm)
5
4
Button
Mechanism
ABS-PC button mechanism
8
5
Button Cover
Depends on the material
selection
8
6
ABS-PC plastic LCD cover
1
7
LCD Display
VA-Type LCD
1
8
Temperature & humidity
sensor, navigation &
programming LED
1
9
Screw
M2x4 (mm)
2
10
BCU
Common for all models
1
Electrical Parameters
Device Name
IBKSWBEE-XYZZ
Buttons Number
1,2,3,4,5,6,7,8,9 &10
Power Supply
KNX BUS Voltage
Current consumption
iBKSW-B08-1YZZ: 18mA
iBKSW-B01-0YZZ: 10mA
LED Indicators
1 x Blue Navigation LED
1 x Red Programming LED
Environmental parameters
Operating Humidity
>90 RH
Storage Humidity
Up to 90%
Operating temperature
-10℃~ +70℃
Storage Temperature
-15°C ~ +90°C
Transport Temperature
-15°C ~ +100°C
Sensor
Temperature Sensor (±0.2°C sens.)
Humidity Sensor (±2 %RH C sens.)
Device Parameters
Protection type
IP20
Mode of communication
S-Mode
Mounting
(35m) Din-Rail
Flammability
Non-Flammable Product
Dimensions (W x H x D) mm
90 X 90 X 12
KNX Bus Connector
0.6 ~0.8 Ø, solid
Output connectors
Screw terminal, 2.5 mm2 stranded ~ 4 mm2 Solid
Tightening torque
Maximum 0.5 Nm
Available colors
White, Champagne, Metallic, Black & Light Gray
Warranty Period
18 months (Made in Turkey)

[e-mail] I www.bee-solutions.tech
By Arrow Engineering –Bulgaria LTD @2020
KNX SWITCH –IBKSWBEE-XYZZ 5
Product Models
Customized switch for GRMS
Customized switch for GRMS
Customized switch for GRMS
8 button with LCD,
metalic gray plastic
8 button with LCD,
natural stainless steel
8 button with LCD,
glossy white plastic
10 buttons champagne,
Aluminum
8 buttons with LCD,
Anthracite Matt plastic
6 buttons mat unbrushed,
natural Eloxal aluminum