Behringer Eurolive B1520DSP User manual

EUROLIVE B1520DSP
User manual
A50-28713-00002

2
EUROLIVE B1520DSP
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) lean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturers instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
12) Where the MAINS plug or an appliance coupler is used
as the disconnect device, the disconnect device shall
remain readily operable.
13) Only use attachments/accessories specified by the
manufacturer.
14) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
15) Unplug this apparatus during lightning storms or when
unused for long periods of time.
16) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
17) AUTION - These service instructions are for use by
qualified service personnel only. To reduce the risk of
electric shock do not perform any servicing other than
that contained in the operation instructions unless you
are qualified to do so.
Important safety instructions
aution:
To reduce the risk of electric shock, do not remove the top
cover (or the re r section). No user service ble p rts inside;
refer servicing to qu lified personnel.
Warning:
To reduce the risk of fire or electric shock, do not expose
this ppli nce to r in nd moisture. The pp r tus sh ll not
be exposed to dripping or spl shing nd no objects filled
with liquids, such s v ses, sh ll be pl ced on the pp r tus.
This symbol, wherever it ppe rs, lerts you to
the presence of uninsul ted d ngerous volt ge
inside the enclosurevolt ge th t m y be
sufficient to constitute risk of shock.
This symbol, wherever it ppe rs, lerts you to
import nt oper ting nd m inten nce instructions
in the ccomp nying liter ture. Ple se re d the
m nu l.
Ventilation:
The ppli nce should be situ ted so th t its loc tion or position
does not interfere with its proper ventil ton. For ex mple, the
ppli nce should not be situ ted on bed, sof rug, or simil r
surf ce th t m y block the ventil tion openings or pl ced in
built-in inst ll tion, such s bookc se or c binet th t m y
impede the flow of ir.
heck the floor:
Alw ys check the floor for st bility before you set up the spe ker
c binet. Vibr ting floors (e.g. elements/components on the
st ge) do not provide reli ble support for spe ker st cks. So,
lw ys pl ce your spe kers on st ble nd level surf ce.
Make sure that speaker cabinets are set up properly:
Set up your spe ker c binet t dist nce to d nce floors or
other udience re s, so s to void spe ker st ck being
knocked over.

B1520DSP
3
EUROLIVE B1520DSP
EUROLIVE
Digital Processor-Controlled 00-Watt 15" PA Speaker System with Integrated Mixer
=High-power 600-Watt 2-way PA sound reinforcement speaker system with integrated mixer for ive
and p ayback app ications
=State-of-the-art 24-bit digita signa processor for u timate system contro :
- Digita crossover, phase and time correction for perfect driver a ignment p us dua compressor/ imiter
for tota system protection
- Digita noise gate, ow-cut fi ter, 2-band EQ, dynamic Contour fi ter for u timate sound reproduction
=2 ULN Mic/Line inputs with individua vo ume contro s and peak LEDs
=Extreme y powerfu 15" ong-excursion driver provides incredib y deep bass and acoustic power
=State-of-the-art 1.75" titanium-diaphragm compression driver for exceptiona ,
high-frequency reproduction
=Additiona Line output enab es inking of additiona speaker systems
=Versati e trapezoida enc osure design a ows different positioning:
- C uster and stacking mode
- Stand mounting with 35-mm po e socket
=Rugged stee gri for optima speaker protection
=Ergonomica y shaped hand es for easy carrying and setup
=High-qua ity components and exceptiona y rugged construction ensure ong ife
=Conceived and designed by BEHRINGER Germany

4
EUROLIVE B1520DSP
Foreword
De r customer,
Welcome to the te m of
BEHRINGER users, nd
th nk you very much
for expressing your
confidence in us by
purch sing these
PA loudspe kers.
Writing this foreword for
you gives me gre t
ple sure, bec use it
represents the culmi-
n tion of m ny months of
h rd work delivered by
our engineering te m to
chieve very mbitious
go l: to develop n
outst nding PA system
th t offers m ximum in
flexibility nd perfor-
m nce through its
impressive sound ch r cter nd outst nding fe tures. The t sk
of designing our new B1520DSP cert inly me nt gre t de l of
responsibility, which we ssumed by focusing on you, the
discerning user nd musici n. Meeting your expect tions lso
me nt lot of work nd night shifts. But it w s fun, too.
Developing product usu lly brings lot of people together,
nd wh t gre t feeling it is when ll who p rticip ted in such
project c n be proud of wh t theyve chieved.
It is our philosophy to sh re our enjoyment with you, bec use
you re the most import nt member of the BEHRINGER te m.
With your highly competent suggestions for new products youve
m de signific nt contribution to sh ping our comp ny nd
m king it successful. In return, we gu r ntee you uncom-
promising qu lity s well s excellent technic l nd udio
properties t n extremely re son ble price. All of this will en ble
you to give free rein to your cre tivity without being h mpered
by budget constr ints.
We re often sked how we m n ge to produce such high-qu lity
devices t such unbeliev bly low prices. The nswer is quite
simple: its you, our customers! M ny s tisfied customers me n
l rge s les volumes en bling us to get better purch sing terms
for components, etc. Isnt it only f ir to p ss this benefit on to
you? Bec use we know th t your success is our success too!
I would like to th nk ll people whose help on the B1520DSP
h s m de it ll possible. Everybody h s m de very person l
contributions, st rting from the designers of the unit to the m ny
st ff members in our comp ny nd fin lly to you, the user of
BEHRINGER products.
My friends, its been worth the effort!
Th nk you very much,
Uli Behringer
Table of contents
1. Introduction ........................................................................ 5
1.1 Before you get st rted ................................................... 5
1.1.1 Shipment .............................................................. 5
1.1.2 Initi l oper tion ..................................................... 5
1.1.3 Online registr tion ................................................ 5
2. ontrol elements and connections ................................. 6
3. Setting up the B1520DSP ................................................. 7
3.1 Tweeter ........................................................................... 7
3.2 How to void feedb ck .................................................. 7
4. Application examples ........................................................ 7
4.1 Present tions ................................................................. 7
4.2 PA systems .................................................................... 8
4.3 Other uses ...................................................................... 9
5. Installation .......................................................................... 9
6. Specifications..................................................................... 9
7. Warranty ............................................................................ 10

5
EUROLIVE B1520DSP
1. Introduction
Th nk you very much for expressing your confidence in
BEHRINGER products by purch sing the EUROLIVE
B1520DSP. The B1520DSP is st te-of-the- rt digit lly
controlled PA spe ker system th t will simply blow you w y.
Its bi- mped 600-W tt engine drives high-efficiency 15" woofer
for brut l punch nd 1.75" tit nium driver for high-end
resolution. The built-in mixer llows you to run the show without
ny extr equipment. A powerful 24-bit DSP controls the
crossover, du l compressor/limiter, ph se nd time corrections
nd even noise g te. The intelligent dyn mic EQ m kes sure
your system sounds perfect t ny sound level.
+Please read this manual to familiarize yourself with
the control elements of the unit and its functions. After
you have carefully read this manual, keep it for future
reference.
1.1 Before you get started
1.1.1 Shipment
Your B1520DSP w s c refully p cked t the ssembly pl nt to
ssure secure tr nsport. Should the condition of the c rdbo rd
box suggest th t d m ge m y h ve t ken pl ce, ple se inspect
the unit immedi tely nd look for physic l indic tions of d m ge.
+Damaged equipment should NEVER be sent directly
to us. Please inform the dealer from whom you
acquired the unit immediately as well as the
transportation company from which you took delivery.
Otherwise, all claims for replacement/repair may be
rendered invalid.
+Please always use the original packaging to avoid
damage due to storage or shipping.
+Never let unsupervised children play with the
B1520DSP or with its packaging.
+Please dispose of all packaging materials in an
environmentally friendly fashion.
1.1.2 Initial operation
Be sure th t there is enough sp ce round the unit for cooling.
To void overhe ting, do not pl ce the B1520DSP on top of
power mps or ne r r di tors, etc.
The m ins connection is m de using the enclosed power cord
nd st nd rd IEC recept cle. It meets ll intern tion l s fety
certific tion requirements.
+Please make sure that all equipment is properly
grounded at all times. For your own safety, never
remove or disable the ground conductor of the unit or
of the A power cord.
Important note concerning installation:
+The sound quality may diminish within the range of
powerful broadcasting stations and high-frequency
sources. Increase the distance between the transmitter
and the device and use shielded cables for all
connections.
1.1.3 Online registration
Ple se remember to register your new BEHRINGER equipment
right fter your purch se by visiting www.behringer.com nd re d
the terms nd conditions of our w rr nty c refully.
Should your BEHRINGER product m lfunction, our go l is to
h ve it rep ired s quickly s possible. To rr nge for w rr nty
service, ple se cont ct the ret iler from whom the equipment
w s purch sed. Should your BEHRINGER de ler not be loc ted
in your vicinity, you m y directly cont ct one of our subsidi ries.
Corresponding cont ct inform tion is included in the origin l
equipment p ck ging (Glob l Cont ct Inform tion/Europe n
Cont ct Inform tion). Should your country not be listed, ple se
cont ct the distributor ne rest you. A list of distributors c n be
found in the support re of our website (www.behringer.com).
Registering your purch se nd equipment with us helps us
process your rep ir cl ims quicker nd more efficiently.
Th nk you for your cooper tion!
1. Introduction

6
EUROLIVE B1520DSP
{1} Power is supplied vi n IEC connector. The m tching
c ble is provided with the unit.
{2} Use the POWER switch to turn on the B1520DSP. Before
connecting the unit to the power m ins, ensure th t the
POWER switch is in OFF position.
+Attention: The POWER switch does not fully
disconnect the unit from the mains. To disconnect the
unit from the mains, pull out the main cable plug or
appliance coupler. When installing the product, ensure
the plug or appliance coupler is readily operable.
Unplug the power cord completely when the unit is
not used for long periods of time.
{3} Use the LEVEL control to djust the sign l g in of the
MIC/LINE inputs. Before you connect or disconnect sign l
source to or from one of the inputs, ple se turn the
corresponding control fully to the left. Once the sign l
source is connected, incre se the volume s desired by
turning the control clockwise. Alw ys m ke sure th t the
CLIP LED {4} does not light up t ll or with sign l pe ks
only.
Line-level signals:
Devices with high output levels (e.g. the outputs of mixing
consoles or CD pl yers) only need little g in. In this c se,
the LEVEL control will mostly be positioned somewhere in
the re m rked "LINE" (left h lf of the control r nge).
Microphone signals
Low-level microphone sign ls need more g in. When
microphones re used, the control will be positioned in the
MIC re (right h lf of the control r nge).
+We would like to draw your attention to the fact that
extremely loud sound levels may damage your hearing
as well as your headphones/loudspeakers. Turn the
LEVEL control fully to the left before you switch on
the unit. Be careful to select a suitable volume at all
times.
{4} The CLIP LED lights up when the input sign l level is too
high. In this c se, turn the LEVEL control {3} to the left
until the LED goes out or only lights up t pe k levels.
{5} Use the MIC/LINE inputs (XLR connectors) for connecting
udio sign ls.
{6} The LINE OUT XLR j ck provides the sign l with no
ddition l g in pplied in order to connect nother
loudspe ker, for ex mple. The output sign l is mix of
both input sign ls. (See Ch pter 4.2 for more inform tion
on how to use sever l loudspe kers)
The B1520DSP is equipped with 2-b nd tone control. E ch
b nd llows you to pply m ximum boost/cut of 15 dB, in its
center position the equ lizer is set to neutr l.
{7} Use the EQ HIGH control to cut or boost the treble r nge
by 15 dB. The cut-off frequency is 12 kHz.
{8} Use the EQ LOW control to cut or boost the b ss r nge by
15 dB. The cut-off frequency is 100 Hz.
{9} The B1220DSP fe tures high-p ss filter with slope of
24 dB/oct. to elimin te unw nted low-frequency content,
such s pop sounds produced by h nd-held microphones,
or rumble or wind noise when using high-sensitivity
microphones. The LOW CUT control djusts the cut-off
frequency. If you w nt to use the B1520DSP in combin tion
with subwoofer, you c n use the high-p ss filter to lower
the b ss r nge reproduced by the subwoofer. This llows
you to oper te the B1520DSP even without n extern l
frequency crossover. Set the cut-off frequency to the
highest frequency th t c n be reproduced by the
subwoofer.
(10) The CONTOUR switch governs the dyn mic contour filter:
SPEE H
Setting the CONTOUR switch to SPEECH (switch not
pressed) will optimize the frequency response for speech
pplic tions. This ensures better intelligibility.
MUSI
Setting the CONTOUR switch to MUSIC (switch pressed)
will optimize the frequency response for music pl yb ck.
2. Control elements and connections
Fig. 2.1: Control elements and connections
2. Contro e ements and connections

7
EUROLIVE B1520DSP
To void feedb ck, it is recommended th t you c refully select
nd direct the microphones used. B sic lly, you should use
microphones with high directivity, i.e. with c rdioid or hyper-
c rdioid pol r p ttern. Never hold microphone so th t its m in
pick-up re points directly tow rds the loudspe ker. When you
hold it with its less sensitive side tow rds the spe ker box, you
c n move closer to the spe ker.
+If you encounter persistent feedback problems,
consider using our proven FEEDBA K DESTROYER
PRO FBQ2496 for line-level signals. For signals with
line or microphone level, we recommend our
BEHRINGER SHARK DSP110.
4. Application examples
4.1 Presentations
With just one B1520DSP nd one or two dyn mic microphones,
you c n set up b sic udio system with very little effort. Th nks
to the built-in mixer section, you c n connect the microphones
directly to the B1520DSP. Mount the B1520DSP on spe ker
st nd for optimum present tion nd intelligibility of nnouncements.
If one B1520DSP is not enough, you c n, of course, use second
or even more loudspe kers.
onnecting microphones:
=Turn the LEVEL controls {3} fully to the left.
=Connect your microphones to the MIC/LINE inputs.
=Switch on the B1520DSP.
=Turn the LEVEL controls {3} gr du lly clockwise to set the
volume of your choice. Observe the CLIP LEDs while
dusting the volume. M ke sure they never shine const ntly
but only light up t pe k levels.
=Use the LINE OUT connector {6} to connect n (option l)
second B1520DSP.
+Never place a microphone directly in front of the
loudspeaker owing to danger of feedback! When
operating the B1520DSP make sure that you always
stay behind the loudspeaker to avoid feedback.
Fig. 4.1: Connecting microphones
(11) The TIMED TURNOFF switch ctiv tes the utom tic turn-
off function:
ON
When the switch is ctu ted (ON position), the utom tic
switch-off is ctive. The loudspe ker is turned off uto-
m tic lly when it receives no sign l for more th n 3
minutes. As soon s sign l is received, the loudspe ker
is switched b ck on.
OFF
If the switch is not ctu ted (OFF position) then the spe ker
rem ins switched on nd c n only be de ctiv ted vi the
POWER switch {2}.
(12) A noise-g te llows you to elimin te unw nted noise during
sign l p uses. This is done by circuit th t mutes the
output when the sign l level drops below preset threshold.
Use the NOISE GATE control to determine the threshold
below which the noise-g te closes.
(13) The TH LED lights up s soon s the sign l level drops
below the threshold v lue djusted with the NOISE GATE
control (12) (the noise-g te closes).
3. etting up the B1520D P
The sound of your B1520DSP l rgely depends on the room
coustics. Ple se observe the following hints to get the most
out of your B1520DSP.
3.1 Tweeter
High frequencies re the very p rt of the udio spectrum th t
ensure cle r perception of sound nd speech intelligibility.
Although these frequencies c n be loc ted most e sily, they
re lso the first to be blocked coustic lly. We therefore
recommend th t you set up your spe kers on spe ker st nds
(not included), so th t the tweeter r di tes its sign ls slightly
bove the he ds of the udience. This will ensure both n
optimum dispersion of the high-frequency content nd
consider bly improved speech intelligibility.
Fig. 3.1: B1520DSP mo nted on a stand
3.2 How to avoid feedback
Alw ys pl ce the microphones (viewed from the udience)
behind the B1520DSP, never in front of it (Fig. 3.2). When you
wish to djust the controls on the B1520DSP while holding
microphone, ple se ppro ch the loudspe ker from the re r to
void feedb ck.
Fig. 3.2: Right and wrong positioning
4. App ication examp es
EUROLIVE B1520DSP
(option l)
EUROLIVE B1520DSP

8
EUROLIVE B1520DSP
4.2 PA systems
PA is short for "public ddress" nd includes ll pplic tions
th t involve l rger udience. This ex mple uses mixing
console s its centr l unit for system oper tion nd connections.
All microphones, feeding nd effects devices, etc. re connected
to the mixing console, which is then linked to the B1520DSP.
onnecting a mixing console:
=Turn the LEVEL controls {3} fully to the left.
=Connect the left output of the mixing console to the MIC/
LINE connector of the left loudspe ker, nd the right mixing
console output to the right loudspe ker.
=Switch on the B1520DSP.
=R ise the level of the mixing console output to level of
0dB.
=Turn the LEVEL controls {3} gr du lly clockwise to set the
volume of your choice. When the CLIP LEDs light up, this
indic tes th t the m ximum volume h s been re ched.
Fig. 4.2: Connecting a mixing console
Inste d of mixing console, you c n lso connect stereo sign l
source, e.g. CD pl yer. In this c se, one B1520DSP is
connected to e ch of the outputs of the sign l source.
onnecting a stereo signal source:
=Turn the LEVEL controls {3} fully to the left.
=Connect the left output of the stereo device to the MIC/LINE
connector of the left loudspe ker, nd the right stereo device
output to the MIC/LINE connector of the right loudspe ker.
=Switch on the B1520DSP.
=R ise the output level of the stereo sign l source (if
v il ble), ensuring th t it does not overlo d the input.
=Turn the LEVEL controls {3} gr du lly clockwise to set the
volume of your choice.
Linking several B1520DSP:
If you need more sound pressure, for ex mple in l rger rooms,
simply incre se the number of loudspe kers on e ch stereo
side. You could pl ce two B1520DSP on e ch stereo side nd
interconnect them (see Fig. 4.3). The loudspe kers c n be
st cked or pl ced one beside the other. When you st ck the
spe kers, the c rrying recesses built into the c binets ensure
the st bility of the st ck. You c n connect microphone, mixing
console or stereo sign l source.
=Connect the LINE OUT connector {6} of the first B1520DSP
to the MIC/LINE input of the next B1520DSP.
+With several B1520DSP speakers connected to each
other, their input impedance will be reduced by half
(two B1520DSPs), or to one third (three B1520DSPs),
etc. Always use the output impedance of the mixing
console as a basis for your calculations!
Fig. 4.3: Linking several B1520DSP speakers
4. App ication examp es
EUROLIVE B1520DSP
(R)
EUROLIVE B1520DSP
(L)
EUROLIVE B1520DSPEUROLIVE B1520DSP

9
EUROLIVE B1520DSP
4.3 ther uses
Monitoring:
When used s monitor, the B1520DSP receives its udio sign l
from the monitor or ux output of the mixing console. If ddition l
B1520DSPs re to be used, you c n loop the udio sign l from
the first spe ker to the next B1520DSP using the line output.
The sound nd volume of e ch B1520DSP c n be djusted with
their own oper ting elements {3} (LEVEL), {7} (EQ HIGH) nd
{8} (EQ LOW).
Keyboard amplification:
Guit rists nd b ssists usu lly h ve their own mplifiers on st ge
to m ke sure they c n he r their own instrument - even when
no monitors re used. In p rticul r on sm ller st ges, the power
delivered by these mps is enough to m tch the volume
produced by other sound sources on st ge. Things re different
with keybo rds nd synthesizers s these usu lly h ve no built-
in spe kers. The B1520DSP llows you to connect nd mix two
keybo rds. If you w nt to pl y more th n two keybo rds, you
c n use submixer (e.g. MicroMIX MX400) to mix down the
sign ls nd route them to the B1520DSP using submixer output
connectors. The second MIC/LINE input c n be used to connect
the monitor sign l from the PA mixing console, so th t you c n
lso he r the other members of your b nd.
5. Installation
Both udio inputs nd outputs of the BEHRINGER B1520DSP
re fully b l nced. To m ximize interference compens tion, try
to est blish b l nced connections to other equipment, whenever
possible.
+Make sure that only competent people install your
B1520DSP. They must be sufficiently earthed during
and after the installation process. Otherwise,
electrostatic discharges may negatively affect the
operating characteristics of your equipment.
Fig. 5.1: XLR connector
6. pecifications
AUDIO INPUTS
MIC/LINE (2) XLR (balanced)
Input impedance 27 kOhm
Sen itivity -40 to +10 dBu
AUDIO OUTPUTS
LINE OUT XLR (balanced)
Output impedance 120 Ohm
PRO ESSING
DSP 24-bit Motorola
AD/DA converter 24-bit / 48 kHz
Limiter dual protection for woofer and driver
Dynamic EQ dual parametric EQ
NOISE GATE variable (off to -30 dB)
TIMED TURNOFF witchable (3 min < -45 dBr)
CONTOUR witchable peech / mu ic contour
EQ HIGH +/- 15 dB (12 kHz)
EQ LOW +/- 15 dB (100 Hz)
LOW CUT 40 - 160 Hz (24 dB/Oct.)
LOUDSPEAKER SYSTEM DATA
Frequency range 40 Hz to 20 kHz
Cro over Butterworth, 1.5 kHz, 24 dB/Oct.
Max. ound pre ure level 128 dB @ 1 m
Di per ion angle 90° x 45°
OUTPUT POWER
Low-frequency range
RMS @ 1% THD 320 W @ 8 Ohm
Peak Power 460 W @ 8 Ohm
High-frequency range
RMS @ 1% THD 80 W @ 8 Ohm
Peak Power 140 W @ 8 Ohm
POWER SUPPLY
Mains Voltage/Fuses
100 V~, 50/60 Hz T 6,3 A H 250 V
120 V~, 60 Hz T 6,3 A H 250 V
220 V~, 50 Hz T 4,0 A H 250 V
230 V~, 50 Hz T 4,0 A H 250 V
Power con umption max. 650 W
Main connector Standard IEC receptacle
DIMENSIONS/WEIGHT
Dimen ion (W x H x D) approx. 18 3/10" x 27 3/5" x 19"
approx. 465 x 700 x 482 mm
Weight approx. 79.4 lb .
approx. 36.5 kg
BEHRINGER is constantly striving to maintain the highest professional standards.
As a result of these efforts, modifications may e made from time to time to existing
products without prior notice. Specifications and appearance may differ from those
listed or illustrated.
6. Specifications

10
EUROLIVE B1520DSP
§ 1 Other warranty rights and national law
1. This w rr nty does not exclude or limit the buyers st tutory
rights provided by n tion l l w, in p rticul r, ny such rights
g inst the seller th t rise from leg lly effective purch se
contr ct.
2. The w rr nty regul tions mentioned herein re pplic ble
unless they constitute n infringement of n tion l w rr nty
l w.
§ 2 Online registration
Ple se do remember to register your new BEHRINGER
equipment right fter your purch se by visiting
www.behringer.com ( ltern tively www.behringer.de) nd kindly
re d the terms nd conditions of our w rr nty c refully.
Registering your purch se nd equipment with us helps us
process your rep ir cl ims quicker nd more efficiently.
Th nk you for your cooper tion!
§ 3 Warranty
1. BEHRINGER (BEHRINGER Intern tion l GmbH including ll
BEHRINGER subsidi ries listed on the enclosed p ge, except
BEHRINGER J p n) w rr nts the mech nic l nd electronic
components of this product to be free of defects in m teri l
nd workm nship for period of one (1) ye r* from the origin l
d te of purch se, in ccord nce with the w rr nty regul tions
described below. If the product shows ny defects within the
specified w rr nty period th t re not excluded from this
w rr nty s described under § 5, BEHRINGER sh ll, t its
discretion, either repl ce or rep ir the product using suit ble
new or reconditioned p rts. In the c se th t other p rts re
used which constitute n improvement, BEHRINGER m y,
t its discretion, ch rge the customer for the ddition l cost
of these p rts.
2. If the w rr nty cl im proves to be justified, the product will
be returned to the user freight prep id.
3. W rr nty cl ims other th n those indic ted bove re
expressly excluded.
§ 4 Return authorization number
1. To obt in w rr nty service, the buyer (or his uthorized
de ler) must c ll BEHRINGER (see enclosed list) during
norm l business hours BEFORE returning the product. All
inquiries must be ccomp nied by description of the
problem. BEHRINGER will then issue return uthoriz tion
number.
2. Subsequently, the product must be returned in its origin l
shipping c rton, together with the return uthoriz tion number
to the ddress indic ted by BEHRINGER.
3. Shipments without freight prep id will not be ccepted.
§ 5 Warranty regulations
1. W rr nty services will be furnished only if the product is
ccomp nied by copy of the origin l ret il de lers invoice.
Any product deemed eligible for rep ir or repl cement under
the terms of this w rr nty will be rep ired or repl ced.
2. If the product needs to be modified or d pted in order to
comply with pplic ble technic l or s fety st nd rds on
n tion l or loc l level, in ny country which is not the country
for which the product w s origin lly developed nd
m nuf ctured, this modific tion/ d pt tion sh ll not be
considered defect in m teri ls or workm nship. The
w rr nty does not cover ny such modific tion/ d pt tion,
irrespective of whether it w s c rried out properly or not.
Under the terms of this w rr nty, BEHRINGER sh ll not be
held responsible for ny cost resulting from such
modific tion/ d pt tion.
3. Free inspections nd m inten nce/rep ir work re expressly
excluded from this w rr nty, in p rticul r, if c used by
improper h ndling of the product by the user. This lso pplies
to defects c used by norm l we r nd te r, in p rticul r, of
f ders, crossf ders, potentiometers, keys/buttons, tubes,
guit r strings, illumin nts nd simil r p rts.
4. D m ges/defects c used by the following conditions re not
covered by this w rr nty:
=improper h ndling, neglect or f ilure to oper te the unit in
compli nce with the instructions given in BEHRINGER
user or service m nu ls.
=connection or oper tion of the unit in ny w y th t does
not comply with the technic l or s fety regul tions
pplic ble in the country where the product is used.
=d m ges/defects c used by force m jeure or ny other
condition th t is beyond the control of BEHRINGER.
5. Any rep ir or opening of the unit c rried out by un uthorized
personnel (user included) will void the w rr nty.
6. If n inspection of the product by BEHRINGER shows th t
the defect in question is not covered by the w rr nty, the
inspection costs re p y ble by the customer.
7. Products which do not meet the terms of this w rr nty will be
rep ired exclusively t the buyers expense. BEHRINGER
will inform the buyer of ny such circumst nce. If the buyer
f ils to submit written rep ir order within 6 weeks fter
notific tion, BEHRINGER will return the unit C.O.D. with
sep r te invoice for freight nd p cking. Such costs will lso
be invoiced sep r tely when the buyer h s sent in written
rep ir order.
§ 6 Warranty transferability
This w rr nty is extended exclusively to the origin l buyer
(customer of ret il de ler) nd is not tr nsfer ble to nyone
who m y subsequently purch se this product. No other person
(ret il de ler, etc.) sh ll be entitled to give ny w rr nty promise
on beh lf of BEHRINGER.
§ 7 laim for damages
F ilure of BEHRINGER to provide proper w rr nty service sh ll
not entitle the buyer to cl im (consequenti l) d m ges. In no
event sh ll the li bility of BEHRINGER exceed the invoiced v lue
of the product.
* Customers in the European Union please contact BEHRINGER Germany Support
for further details.
Technical specifications and appearance are su ject to change without notice. The information contained herein is correct at the time of printing. All trademarks (except
BEHRINGER, the BEHRINGER logo, JUST LISTEN and EUROLIVE) mentioned elong to their respective owners and are not affiliated with BEHRINGER. BEHRINGER
accepts no lia ility for any loss which may e suffered y any person who relies either wholly or in part upon any description, photograph or statement contained herein.
Colors and specifications may vary slightly from product. Products are sold through our authorized dealers only. Distri utors and dealers are not agents of BEHRINGER and
have a solutely no authority to ind BEHRINGER y any express or implied undertaking or representation. No part of this manual may e reproduced or transmitted in any
form or y any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of BEHRINGER
International Gm H.
ALL RIGHTS RESERVED.
© 2008 BEHRINGER International Gm H, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Muenchheide II, Germany,
Tel. [phone], Fax [phone]
7. Warranty
7. Warranty