Belanger AirBLade Mix & Match User manual

1MANUL011
REV 02
Belanger, Inc.
P.O. Box 5470
Northville, MI 48167-5470
Customer Service Phone [phone]
Fax [phone]
www.belangerinc.com
®
Drye
r
Mix & Match

Belanger Equipment Owners Manual
AirBlade® Dryer Mix & Match
Copyright 2010
Belanger, Inc®
This manual and the accompanying equipment are protected by United States and International copyright and patent laws. You
may make one copy of this manual. Do not make additional copies of this manual or electronically transmit it in any form
whatsoever, in whole or in part, without the prior written permission of Belanger, Inc.®

AIRBLADE® DRYER Mix and Match
1MANUL011 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]
Table of Contents
Belanger Incorporated Limited Warranty........................................................ 3
Operational Warning......................................................................................... 4
Introduction ....................................................................................................... 5
Important Safety Information....................................................................................................5
Safety Symbols and Signal Words .......................................................................................... 5
IMPORTANT Safety Information – MUST READ .................................................................... 6
Safety Warnings....................................................................................................................... 6
Available Components: Floor Mounted.................................................................................... 9
Available Components: Wall Mounted................................................................................... 12
Before You Get Started..........................................................................................................14
Specifications.................................................................................................. 15
Physical Dimensions.............................................................................................................. 15
Utility Requirements............................................................................................................... 16
Installation ....................................................................................................... 17
AirBlade® Wall mounting Utility Information .......................................................................... 17
AirBlade® Head Beam Cover Kit........................................................................................... 18
2-Nozzle System Overview.................................................................................................... 19
2-Nozzle System Overview: Floor Mounted .......................................................................... 20
2-Nozzle Frame Assembly: Floor Mounted ........................................................................... 21
2-Nozzle System Overview: Wall Mounted............................................................................ 23
2-Nozzle Frame Assembly: Wall Mounted............................................................................. 24
4-Nozzle “Select” System Overview ...................................................................................... 28
4-Nozzle “Select” System with Air Cannons Overview: Floor Mounted ................................ 30
4-Nozzle “Select” System with Side Kicks® Overview: Floor Mounted................................. 31
4-Nozzle “Select” Frame Assembly: Floor Mounted.............................................................. 32
4-Nozzle System Overview: Wall Mounted............................................................................ 42
4-Nozzle Frame Assembly: Wall Mounted............................................................................. 43
6-Nozzle System Overview.................................................................................................... 50
6-Nozzle System Overview: Floor Mounted .......................................................................... 51
6-Nozzle Frame Assembly: Floor Mounted ........................................................................... 52
6-Nozzle System Overview: Wall Mounted............................................................................ 58
6-Nozzle Frame Assembly: Wall Mounted............................................................................. 59
10-Nozzle System Overview.................................................................................................. 70
10-Nozzle System Overview: Floor Mounted ........................................................................ 71
10-Nozzle Frame Assembly: Floor Mounted ......................................................................... 72
10-Nozzle System Overview: Wall Mounted.......................................................................... 82
10-Nozzle Frame Assembly: Wall Mounted........................................................................... 83

AIRBLADE® DRYER Mix and Match
2Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]MANUL011
Table of Contents
Maintenance ...................................................................................................101
Routine Procedures ............................................................................................................. 101
Trouble Shooting.................................................................................................................. 102
Exploded Parts View............................................................................................................ 103
Motor Maintenance Supplied by Baldor® ............................................................................ 114

AIRBLADE® DRYER Mix and Match
1MANUL011 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]
Belanger Incorporated Limited Warranty
LIMITED WARRANTY: Equipment: Seller warrants to the original purchaser that the goods sold hereunder, which are
fabricated by Seller, shall be free from defects in workmanship and material under normal use and service for a period of 1 year
plus 30 days from the date of invoice - CAT®Pumps will be warranted for 2 years from the date of invoice. All
warranties, express, implied, or statutory, pertaining to Seller’s machinery, parts, and equipment are fully set forth
herein. This limited warranty applies to the original purchaser only and is not transferable. No addition to or
modification of any of the provisions of this stated Limited Warranty shall be binding upon the Seller, unless made in
writing and signed by a duly authorized employee of Seller. This warranty is subject to the following limitations: (1)
This warranty shall be void if the factory specifications for operation and maintenance, found in original equipment
manuals, and component manuals, are not followed, or if other than factory authorized erection, alterations or
modifications are made to any parts or equipment; (2) Defective parts are warranted to the Purchaser for repair or
replacement through an authorized distributor or value added reseller (VAR) of Seller, or direct with Seller for a
period of 13 months from the date of invoice. Parts warranty excludes all claims for failure resulting from normal
wear and tear to the depreciable parts, improper installation, omission of factory specified preventative
maintenance, misuse, abuse, negligence, third party damages, or acts of God. Purchaser agrees to submit to and
assist Seller or its authorized distributor or value added reseller (VAR) in conducting in-warranty inspections of the
machinery and equipment including inspection of any part claimed to be defective by the Purchaser; (3) Labor to
repair or replace parts is warranted to Purchaser during normal business hours through an authorized distributor or
value added reseller (VAR) of Seller, or direct with Seller, for 120 days from date of invoice. Labor warranty
excludes all claims for failure resulting from normal wear and tear to the depreciable parts, improper installation, and
omission of factory specified preventative maintenance, misuse, abuse, negligence, third party damages, or acts of
God. Seller reserves the sole right to make determinations on the above stated limitation. All labor and service
provided beyond the labor warranty period shall be subject to labor charges at the rates established by the local
authorized distributor or value added reseller (VAR) or direct with Seller; (4) This warranty shall be void for all
equipment failures and premature component wear caused by the use of corrosive chemicals in the wash process.
The following list includes some, but not all, of the particularly corrosive chemicals that if used in conjunction with
Belanger equipment will void the warranty: Hydrofluoric Acid, Ammonium Bi-flouride, Bromic Acid, Muriatic Acid,
Sulfonic Acid, Phosphoric Acid, Hydrogen Cyanide, Hydrochloric Acid, Sodium Hydroxide and Chlorinated Solvents.
(5) Seller makes no warranty, express or implied, with respect to the design or operation of any entire system, in
which Seller’s goods sold hereunder are mere components. (6) In no event shall Seller be liable for any incidental,
special, consequential or exemplary damages resulting from the furnishing, performance or use of any goods or
services sold pursuant hereto, whether due to a breach of contract, breach of warranty, the negligence of Seller or
to otherwise; not for loss of business; inconvenience, or property damage of any kind; not for any damages of
whatever nature resulting in any way from the purchaser’s selection and use of any chemicals not manufactured
exclusively by seller but used with the purchased goods; or for any service not expressly provided herein related to
or arising from the equipment or goods sold. This limitation of liability extends to purchaser’s use of any engineering
recommendations, sales representations, technical assistance, advice or data supplied by seller to purchaser in
connection with the goods or services supplied, other than that information contained in Belanger manuals.
Parts: Seller warrants to the original purchaser that the Replacement Parts sold hereunder, shall be free from
defects in workmanship and material under normal use and service for a period of 30 days from the date of invoice.
This limited warranty applies to the original purchaser only and is not transferable. (1) This warranty shall be void if
the factory specifications for operation and maintenance are not followed; (2) Parts warranty excludes all claims for
failure resulting from normal wear and tear to the depreciable parts, improper installation, omission of factory
specified preventative maintenance, misuse, abuse, negligence, third party damages, or acts of God. (3) This
warranty shall be void for all replacements parts failures and premature component wear caused by the use of
corrosive chemicals in the wash process. The following list includes some, but not all, of the particularly corrosive
chemicals that if used in conjunction with Belanger replacement parts will void the warranty: Hydrofluoric Acid,
Ammonium Bi-flouride, Bromic Acid, Muriatic Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen Cyanide, Hydrochloric
Acid, Sodium Hydroxide and Chlorinated Solvents.
THIS LIMITED WARRANTY FOR EQUIPMENT AND REPLACEMENT PARTS IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, WHETHER STATUTORY OR OTHERWISE, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright © 2000 by Belanger, Inc. All rights reserved. No part of this work may be reproduced or transmitted in any form or by
any means, electronic or mechanical, including photocopying and recording, or by any information storage or retrieval system,
except as may be expressly permitted by the 1976 Copyright Act. Revised as of 8-15-01. Belanger reserves the right to change or
modify the Belanger Inc. Limited Warranty without notice.

AIRBLADE® DRYER Mix and Match
4Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]MANUL011
Operational Warning
Formulations containing the chemicals listed below are particularly dangerous and should not
be used even at low concentrations:
•Hydrofluoric Acid
•Ammonium Bi-flouride
•Bromic Acid
•Muriatic Acid
•Sulfonic Acid
•Phosphoric Acid
•Hydrogen Cyanide
•Hydrochloric Acid
•Chlorinated Solvents
Belanger, Inc., does not endorse or condone the use of chemicals that are potentially dangerous
to human health, the environment or property. Belanger recognizes that it is the right and sole
decision of the end user operators of our equipment as to the type and dilution ratio of the
chemicals used in their facilities. We strongly recommend that the end user does not select
products containing any of the chemicals listed above as an ingredient in the wash solutions.
The chemicals listed above are potentially dangerous to human health, and have a detrimental,
deteriorating effect on the equipment and the facility. Be advised that a portion of, or all of your
warranty will be voided if you determine to use any of the chemicals listed above as an
ingredient in the wash solutions in conjunction with your Belanger automatic car wash
equipment:
Limitation (4), of Paragraph (8), Limited Warranty, of the Belanger Terms and Conditions of
Sales describes the potential limitation of warranty due to your chemical selection:
(4) This warranty shall be void for all equipment failures and premature component wear
caused by the use of corrosive chemicals in the wash process. The following list includes
some, but not all, of the particularly corrosive chemicals that if used in conjunction with
Belanger equipment will void the warranty: Hydrofluoric Acid, Ammonium Bi-flouride, Bromic
Acid, Muriatic Acid, Sulfonic Acid, Phosphoric Acid, Hydrogen Cyanide, Hydrochloric Acid,
and Chlorinated Solvents. The Purchaser also agrees to accept the responsibility and
liability for the selection and use of any chemicals listed above;
However, should the end user decide to use formulations containing any of the above
ingredients, the end user should institute a comprehensive training program and implement
detailed operational parameters within their organization for the proper handling and treatment
of such products to minimize the potential dangers involved. Consult your chemical supplier for
assistance in establishing operational guidelines in the use of their products. MSDS (Material
Safety Data Sheet) should be obtained from the chemical supplier before using any chemical
formulation.
CAUTION
During the installation process the installer is responsible for re-tightening ALL
lugs, set screws and terminals located in the electrical panels. Components may
vibrate loose during shipping.

AIRBLADE® DRYER Mix and Match
1MANUL011 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]
Introduction
Important Safety Information
This section introduces the hazard and safety precautions associated with installing, maintaining or servicing this product.
Before performing any task on this product, read this safety information and the applicable sections in this manual, where
additional hazards and safety precautions for your task may be found. Electrical shock could occur and cause death or
serious injury if these safe service procedures are not followed.
Safety Symbols and Signal Words
Alert Symbol
This safety alert symbol is used in this manual and on warning labels to alert you to precautions,
which must be followed to prevent potential personal safety hazards. Obey safety directives that
follow this symbol to avoid possible injury or death.
Signal Words
The signal words used in this manual and on warning labels tell you the seriousness of particular safety hazards. The
precautions that follow must be followed to prevent death, injury or damage to the equipment.
DANGER
This signal word is used to alert you to a hazard or unsafe practice which WILL RESULT IN
DEATH OR SERIOUS INJURY
This alerts you to a hazard or unsafe practice which COULD RESULT IN DEATH OR
SERIOUS INJURY
CAUTION
This signal word designates a hazard or unsafe practice, which MAY RESULT IN MINOR
INJURY
CAUTION
When used by it self, CAUTION designates a hazard or unsafe practice which MAY RESULT
IN PROPERTY OR EQUIPMENT DAMAGE
Before You Begin
Only trained or authorized individuals knowledgeable in the related procedures should install, inspect, maintain or
service this equipment.
Read the Manual
Read, understand and follow this manual and any other labels or related materials supplied with this equipment. If you
do not understand the procedure, call a Belanger, Inc. representative at 248-349-7010. It is imperative to your safety
and the safety of others to understand the procedures before beginning work.

AIRBLADE® DRYER Mix and Match
6Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]MANUL011
Introduction
IMPORTANT Safety Information – MUST READ
Safety Warnings
DANGER
DISCONNECT MAIN POWER SUPPLY PRIOR TO
SERVICING OR MAINTAINING EQUIPMENT
Belanger recommends that all workers observe the OSHA (U.S. Department of
Labor Occupational Safety & Health Administration) Lockout / Tagout procedure
prior to performing service or maintenance on machinery and equipment. Doing
so will prevent unexpected energization, startup, or release of hazardous energy
while maintenance and servicing activities are being performed.
BE SURE TO OBSERVE OPERATING ENVELOPE.
EQUIPMENT MAY START UNEXPECTICALLY. OVERHEAD,
ROTATING AND/OR MOVING COMPONENTS COULD
RESULT IN SERIOUS INJURY OR DEATH.
BE AWARE OF FOREIGN OBJECTS IN THE AREA
SURROUNDING A ROTATING PIECE OF EQUIPMENT.
OBJECTS MAY BECOME TANGLED WITH EQUIPMENT AND
COULD RESULT IN SERIOUS INJURY OR DEATH.
CAUTION
BE AWARE OF HAZARDS ASSOCIATED WITH
EQUIPMENT INSTALLED ON THE FLOOR
THAT MAY BE A TRIP HAZARD.
It is imperative to your safety and the safety of others to always follow
safe work procedures.

AIRBLADE® DRYER Mix and Match
1MANUL011 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]
Introduction
Congratulations on your purchase of the Belanger, Inc. AirBlade® Dryer.
The AirBlade® Dryer is available in various configurations. The configurations are as follows:
AirBlade® Floor
Mounted
AirBlade® Select
Floor Mounted
AirBlade® Express
Floor Mounted
AirBlade® Express 180
Floor Mounted
AirBlade® Wall
Mounted
AirBlade® Select Wall
Mounted
AirBlade® Express
Wall Mounted
AirBlade® Express 180
Wall Mounted
AirBlade® Select with Side Kick® Option
AirBlade® Select with SideKick,
Floor Mounted

AIRBLADE® DRYER Mix and Match
8Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]MANUL011
Introduction
When assembling the AirBlade® Dryer, pay close attention to the required operating
envelope. That is the space needed to operate properly shown in the drawings.
This manual will cover all procedures for all available systems.
It would be very beneficial to have a leveler of some sort on hand. In order to achieve
optimum performance, the Air Cannon™ nozzles for the 40HP and the 60HP systems
should be mounted in specific positions. Levelers can be purchased at any good hardware
store (Home Depot).
This document is laid out in eight sections.
•2 Nozzle Wall Mount System •2 Nozzle Floor Mount System
•4 Nozzle Wall Mount System •4 Nozzle Floor Mount System
•6 Nozzle Wall Mount System •6 Nozzle Floor Mount System
•10 Nozzle Wall Mount System •10 Nozzle Floor Mount System
Refer to the supplied drawings for positioning nozzles to the proper angles.
Nozzle location and positioning was determined at the factory to fit a wide brand
of vehicles. Your installation preference may vary based on vehicle and building
restraints.
Typical Leveler

AIRBLADE® DRYER Mix and Match
1MANUL011 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]
Introduction
Available Components: Floor Mounted
Item Description: 2 Nozzle
Black 2 Nozzle Floor Mount AirBlade®
Blue 2 Nozzle Floor Mount AirBlade®
Green 2 Nozzle Floor Mount AirBlade®
Orange 2 Nozzle Floor Mount AirBlade®
Red 2 Nozzle Floor Mount AirBlade®
Yellow 2 Nozzle Floor Mount AirBlade®
Gray 2 Nozzle Floor Mount AirBlade®
Item Description: Select with Air Cannons (4 Nozzle)
Black 4 Nozzle Floor Mount AirBlade® Select
Blue 4 Nozzle Floor Mount AirBlade® Select
Green 4 Nozzle Floor Mount AirBlade® Select
Orange 4 Nozzle Floor Mount AirBlade® Select
Red 4 Nozzle Floor Mount AirBlade® Select
Yellow 4 Nozzle Floor Mount AirBlade® Select
Gray 4 Nozzle Floor Mount Air AirBlade® Select
Item Description: Select with Side Kicks® (4 Nozzle)
Black 4 Nozzle Floor Mount with Side Kicks®: Select
Blue 4 Nozzle Floor Mount with Side Kicks®: Select
Green 4 Nozzle Floor Mount with Side Kicks®: Select
Orange 4 Nozzle Floor Mount with Side Kicks®: Select
Red 4 Nozzle Floor Mount with Side Kicks™: Select
Yellow 4 Nozzle Floor Mount with Side Kicks®: Select
Gray 4 Nozzle Floor Mount with Side Kicks®: Select
Item Description: 6 Nozzle Item Description: 10 Nozzle
Requires one, 4-Nozzle and one 2-Nozzle Requires two, 4-Nozzles and one 2-Nozzle

AIRBLADE® DRYER Mix and Match
10 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]MANUL011
Introduction
Available Components: Floor Mounted
2-Nozzle Floor Mount Aluminum: Basic
Description Quantity
Floor Mount Frame Assembly Aluminum 1
AirBlade Upper Mount Assembly Aluminum 2
AirBlade Housing Lift Assembly 1
2-Nozzle Floor Mount Powder Coated: Basic
Description Quantity
Floor Mount Frame Assembly Powder Coated 1
AirBlade Upper Mount Assembly Powder Coated 2
AirBlade Housing Lift Assembly 1
4-Nozzle Floor Mount with Air Cannons, Aluminum: Select
Description Quantity
Floor Mount Frame Assembly Aluminum 1
AirBlade Upper Mount Assembly Aluminum 2
AirBlade Lower Mount Assembly Aluminum 2
AirBlade Housing Lift Assembly 1
4-Nozzle Floor Mount with Air Cannons, Powder Coated: Select
Description Quantity
Floor Mount Frame Assembly Powder Coated 1
AirBlade Upper Mount Assembly Powder Coated 2
AirBlade Lower Mount Assembly Powder Coated 2
AirBlade Housing Lift Assembly 1
4-Nozzle Floor Mount with Side Kicks®, Aluminum: Select
Description Quantity
Floor Mount Frame Assembly Aluminum 1
AirBlade Upper Mount Assembly Aluminum 2
Aluminum Mix and Match Side Nozzle Mount Assembly 1
AirBlade Housing Lift Assembly 1
4-Nozzle Floor Mount with Side Kicks®, Powder Coated: Select
Description Quantity
Floor Mount Frame Assembly Powder Coated 1
AirBlade Upper Mount Assembly Powder Coated 2
Powder Coated Mix and Match Side Nozzle Mount Assembly 1
AirBlade Housing Lift Assembly 1

AIRBLADE® DRYER Mix and Match
1MANUL011 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]
Introduction
Available Components: Floor Mounted
6-Nozzle Floor Mount Aluminum
Description Quantity
Floor Mount Frame Assembly Aluminum 2
AirBlade Upper Mount Assembly Aluminum 4
AirBlade Lower Mount Assembly Aluminum 2
AirBlade Housing Lift Assembly 1
6-Nozzle Floor Mount Aluminum
Description Quantity
Floor Mount Frame Assembly Aluminum 2
AirBlade Upper Mount Assembly Aluminum 4
AirBlade Lower Mount Assembly Aluminum 2
AirBlade Housing Lift Assembly 1
10-Nozzle Floor Mount Aluminum
Description Quantity
Floor Mount Frame Assembly Aluminum 3
AirBlade Upper Mount Assembly Aluminum 6
AirBlade Lower Mount Assembly Aluminum 4
AirBlade Housing Lift Assembly 1
10-Nozzle Floor Mount Powder Coated
Description Quantity
Floor Mount Frame Assembly Powder Coated 3
AirBlade Upper Mount Assembly Powder Coated 6
AirBlade Lower Mount Assembly Powder Coated 4
AirBlade Housing Lift Assembly 1

AIRBLADE® DRYER Mix and Match
12 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]MANUL011
Introduction
Available Components: Wall Mounted
Item Description: 2 Nozzle
Black 2 Nozzle Wall Mount AirBlade®
Blue 2 Nozzle Wall Mount AirBlade®
Green 2 Nozzle Wall Mount AirBlade®
Orange 2 Nozzle Wall Mount AirBlade®
Red 2 Nozzle Wall Mount AirBlade®
Yellow 2 Nozzle Wall Mount AirBlade®
Gray 2 Nozzle Wall Mount AirBlade®
Item Description: 4 Nozzle
Black 4 Nozzle Wall Mount AirBlade® Select
Blue 4 Nozzle Wall Mount AirBlade® Select
Green 4 Nozzle Wall Mount AirBlade® Select
Orange 4 Nozzle Wall Mount AirBlade® Select
Red 4 Nozzle Wall Mount AirBlade® Select
Yellow 4 Nozzle Wall Mount AirBlade® Select
Gray 4 Nozzle Wall Mount AirBlade® Select
Item Description: 6 Nozzle Item Description: 10 Nozzle
Requires one, 4-Nozzle and one 2-Nozzle Requires two, 4-Nozzles and one 2-Nozzle
2-Nozzle Wall Mount Aluminum
Description Quantity
Dryer Wall Mount Assembly Aluminum 1
AirBlade Upper Mount Assembly Aluminum 2
AirBlade Housing Lift Assembly 1
2-Nozzle Wall Mount Powder Coated
Description Quantity
Dryer Wall Mount Assembly Powder Coated 1
AirBlade Upper Mount Assembly Powder Coated 2
AirBlade Housing Lift Assembly 1
4-Nozzle Wall Mount Aluminum
Description Quantity
Dryer Wall Mount Assembly Aluminum-w/high sides 1
AirBlade Upper Mount Assembly Aluminum 2
AirBlade Lower Mount Assembly Aluminum 2
AirBlade Housing Lift Assembly 1
4-Nozzle Wall Mount Powder Coated
Description Quantity
Dryer Wall Mount Assembly Powder Coated-w/high sides 1
AirBlade Upper Mount Assembly Powder Coated 2
AirBlade Lower Mount Assembly Powder Coated 2
AirBlade Housing Lift Assembly 1

AIRBLADE® DRYER Mix and Match
1MANUL011 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]
Introduction
Available Components: Wall Mounted
6-Nozzle Wall Mount Aluminum
Description Quantity
Dryer Wall Mount Assembly Aluminum 1
Dryer Wall Mount Assembly Aluminum-w/low sides 1
AirBlade Upper Mount Assembly Aluminum 4
AirBlade Lower Mount Assembly Aluminum 2
AirBlade Housing Lift Assembly 1
6-Nozzle Wall Mount Powder Coated
Description Quantity
Dryer Wall Mount Assembly Powder Coated-w/high sides 1
Dryer Wall Mount Assembly Powder Coated 1
AirBlade Upper Mount Assembly Powder Coated 4
AirBlade Lower Mount Assembly Powder Coated 2
AirBlade Housing Lift Assembly 1
10-Nozzle Wall Mount Aluminum
Description Quantity
Dryer Wall Mount Assembly Aluminum 1
Dryer Wall Mount Assembly Aluminum-w/high sides 2
AirBlade Upper Mount Assembly Aluminum 6
AirBlade Lower Mount Assembly Aluminum 4
AirBlade Housing Lift Assembly 1
10-Nozzle Wall Mount Powder Coated
Description Quantity
Dryer Wall Mount Assembly Powder Coated-w/high sides 1
Dryer Wall Mount Assembly Powder Coated 2
AirBlade Upper Mount Assembly Powder Coated 6
AirBlade Lower Mount Assembly Powder Coated 4
AirBlade Housing Lift Assembly 1

AIRBLADE® DRYER Mix and Match
14 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]MANUL011
Introduction
Before You Get Started
Tools needed for installation:
Hammer drill with a 1/2” and a 5/8” bit Work gloves
Tape measure (12 foot or greater) Tin snips
25 foot extension cord Safety glasses
Miscellaneous hand tools Level
Leveler Fork-lift
Note: Uncrate and inspect shipment for damage, and to verify that all pieces are there. If there
is any damaged equipment, file a claim with the trucking company immediately. Receiving
party is responsible for filing claim with trucking company. Notify your local distributor
or Belanger, Inc. immediately. If shipment is determined damaged or incomplete.
CAUTION
It is recommended that a licensed electrician is contracted to perform all
electrical installations.
Disconnect and lockout electrical power before servicing any equipment!
Always wear safety glasses when performing maintenance on any equipment.

AIRBLADE® DRYER Mix and Match
1MANUL011 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]
Specifications
Physical Dimensions
AirBlade® / 20 HP Floor Mounted AirBlade® / 20 HP Wall Mounted
Tunnel space required 36-1/8" Tunnel space required 23-3/4"
Unit height overall 122" Unit height overall 122"
Unit width overall 164" Unit width 166" min. 204-1/2" max.
AirBlade Select™ with Air Cannons/ 40 HP Floor Mounted AirBlade Select ™ with Air Cannons/ 40 HP Wall Mounted
Tunnel space required 58-9/16" Tunnel space required 52-1/4"
Unit height overall 122" Unit height overall 122"
Unit width overall 166" Unit width 166" min. 204-1/2" max.
AirBlade Select™ with Side Kicks®/ 40 HP Floor Mounted
Tunnel space required 55-1/2"
Unit height overall 122"
Unit width overall 170"
AirBlade Express™ / 60 HP Floor Mounted AirBlade Express ™ / 60 HP Wall Mounted
Tunnel space required 90-1/2" Tunnel space required 90-1/2"
Unit height overall 122" Unit height overall 122"
Unit width overall 166" Unit width 166" min. 204-1/2" max.
AirBlade Express™ / 100 HP Floor Mounted AirBlade Express ™ / 100 HP Wall Mounted
Tunnel space required 179" Tunnel space required 179"
Unit height overall 122" Unit height overall 122"
Unit width overall 166" Unit width 166" min. 204-1/2" max.

AIRBLADE® DRYER Mix and Match
16 Belanger, Inc. * 1001 Doheny Ct. * Northville, MI 48167 * Ph [phone] * Fax [phone]MANUL011
Specifications
Utility Requirements
Note: See Conduit Electrical information page of system print set for full details.
AIRBLADE DRYER STYLE AMPS
IN FLA
LARGEST
MOTOR
FLA
VOLTS Hz PHASE
64 32.2 208 60 3
56 28 230 60 3
28 14 460 60 3
34 17 380 50 3
32 16 415 50 3
AIRBLADE DRYER – 20HP
22 11 575 60 3
129 32.2 208 60 3
112 28 230 60 3
56 14 460 60 3
68 17 380 50 3
64 16 415 50 3
AIRBLADE DRYER SELECT with
AIR CANNONS – 40 HP
44 11 575 60 3
129 32.2 208 60 3
112 28 230 60 3
56 14 460 60 3
68 17 380 50 3
64 16 415 50 3
AIRBLADE DRYER SELECT with SIDE
KICKS® – 40 HP
44 11 575 60 3
193 32.2 208 60 3
168 28 230 60 3
84 14 460 60 3
102 17 380 50 3
96 16 415 50 3
AIRBLADE DRYER EXPRESS – 60HP
66 11 575 60 3
322 32.2 208 60 3
280 28 230 60 3
140 14 460 60 3
170 17 380 50 3
160 16 415 50 3
AIRBLADE DRYER EXPRESS 180 – 100HP
110 11 575 60 3
See Local electrical codes for service factor amps. Size load center and wires accordingly.