Black Horse BEDE BD-5J User manual

Instruction Manual book
SPECIFICATION


Wingspan : 1,450mm 57.09 in.


Length : 1,140 mm 44.88 in.


Weight : 3.3kg 7.26 Lbs.


Radio : 05 channels.


Servo : 07miniservos+3servosRetracts(FUTABAS3170G)


EDF: 90mm 6 BLADE with OUTRUNER MOTOR 3553- 1750 KV 1500W


Battery:6S-LIPO-22.2V-5500mAh


Speed control: 70A
Includingnosegearsmechanicretractswitholeostruts. MadeinVietnam.
ITEM CODE:BH 139

2
BEDE BD-5J Item code: BH139 . Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your BEDE BD-5J. Use the parts listing below to
identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenewpilotonhiswaytosuccessfulR/Cflight.Theywillalso be able
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
Landinggear.....
Toavoid scratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand to protect the table.Keep acouple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevatorhalves.
SUGGESTION.
NOTE.
Pleasetrialfitalltheparts.Makesureyouhave
the correct parts and that they fit and are
alignedproperlybeforegluing! This willassure
proper assembly.BEDE BD-5J ARF is hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderandacetone.Donotletthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.

3
BEDE BD-5J Item code: BH139 . Instruction Manual
Caution:
this model is not a toy!
Ifyou are a beginner to this typeof powered model, please askan experienced model flyer forhelp
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
youhave to carry out is important and mustbe done carefully.Themodel will only be strongand fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Wear safety glasses.
+ The glow plug clip must be securely attached to the glow plug.
+ Do not start the EDF if people are near.

4
BEDE BD-5J Item code: BH139 . Instruction Manual
REPLACEMENT LARGE PARTS
REPLACEMENT SMALL PARTS
1.Retract main gear.
6.Cable wire of nose gear.
4. Wheels
8.Antenna.
3.Plastic parts for retract servos.
D. Rudder.
E. Carbon tube wing dihedral brace.
C3.Elevator
B. Wing panel(B1,B2).
A. Fuselage.
C.Horizontal stabilizer(C1,C2). F. Carbon tube Horizontal stabilizer.
K.Pilot
2.Retract nose gear.
7.Plastic part of tail fuselage.
5.Plywood of nose gear
G
k
G.Decal sheet
6

5
BEDE BD-5J Item code: BH139 . Instruction Manual
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
I. AILERON.
1.INSTALLING THE AILERON SERVOS.
Top side
bottom side.
Aileron
Flap
Temporary pin to
keep hinge centered.
Cutthe covering
awayfromtheslot.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
2)Using a modelingknife, remove thecov-
ering at possition show below.
Servotray.
Remove
covering
bottom side.

6
BEDE BD-5J Item code: BH139 . Instruction Manual
5. Instal servo tray with aileron servo into
the wing as same as picture below.
2x10mm.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
4)Drill 1,6mm pilot holes throughthe block
of wood for each of the four mounting screws
provided with the servo.
Secure.
thread
Electric
wire.
Secure.
Aileroncontrol horn
InstallAileron control horn as same as
picturebelow.
A+B Epoxy
PLUS glue
Repeat the procedure for the other wing
half.
INSTALLING THE AILERON CONTROL

7
BEDE BD-5J Item code: BH139 . Instruction Manual
Repeat the procedure for the other wing
half.
Installing the aileron linkages as pictures
below.
2x10mm.
INSTALLING THE AILERON
LINKAGES.
II. FLAP
1.INSTALLING THE FLAP SERVO
Aileron
control horn
Flap. Bottom side
Secure
Repeat the procedure for the other wing
half.
35mm.

8
BEDE BD-5J Item code: BH139 . Instruction Manual
Repeat the procedure for the other wing
half.
Installflap controlhorn assame as
picturebelow.
ControlhornFlap.
2.INSTALLING THE FLAP
CONTROL HORN.
A+B Epoxy
PLUS glue
Control horn
of the flap.
Installing the flap linkages as pictures
below.
3.INSTALLING THE FLAP
LINKAGES.
35mm
Bottom side.
Topside.
INSTALLING RETRACT SERVOS.
Retract
servos
Topside.

9
BEDE BD-5J Item code: BH139 . Instruction Manual
PARTSREQUIRED
INSTALLING RETRACTABLE
LANDING GEAR.
5x30mm.
3x15mm.
Retract
servo
Bottom side.
Retract
servo.
Retract
servo.

10
BEDE BD-5J Item code: BH139 . Instruction Manual
Secure.
Secure.
5x30mm.
Secure.
3x15mm.

11
BEDE BD-5J Item code: BH139 . Instruction Manual
C/Aglue.
Bottom side.
Flap
Bottom side
secure.
Plastic parts for Retract servos. Top side.
See pictures below:
INSTALLING THE RETRACT PUSHROD.

12
BEDE BD-5J Item code: BH139 . Instruction Manual
2x10mm.
Secure.
Bottom side
Top side
Open
Markline.
Seepictures below:
(Notincluded)
INSTALLINGELECTRIC EDF-90MM.
Repeat the procedure for the other gear.
Retract
pushrod.

13
BEDE BD-5J Item code: BH139 . Instruction Manual
3x15mm.
Cut
Right side.
Secure.
Left side.

14
BEDE BD-5J Item code: BH139 . Instruction Manual
1. Install the rubber grommets and brass
collets into the elevator servo. Test fit the
servo into the servo tray.
2. Mount the servo to the tray using the
mounting screws provided with your radio
system.
Elevator servo
Plastic part of tail fuselage.
Secure.
A+B Epoxy
PLUSglue
Elevator
servo
INSTALLING THE ELEVATOR
SERVOS.

15
BEDE BD-5J Item code: BH139 . Instruction Manual
HORIZONTAL STABILIZER.
Horizontal stabilizer installation
See picture below.
Bottomside
carbon tube.
148 mm
8mm
Epoxy
glue.
Lefthorizontal
stabilizer
Right horizontal
stabilizer
C/Aglue.
Right side

16
BEDE BD-5J Item code: BH139 . Instruction Manual
Epoxy
glue.
C/Aglue.
Temporary pin to
keep hinge centered.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
Bottom side
Elevator control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
ELEVATOR CONTROL HORN
INSTALLATION.
Bottom side
Installing elevator.
See picture below.
Controlhornofelevator.
Cutthe covering
awayfromtheslot.

17
BEDE BD-5J Item code: BH139 . Instruction Manual
A+B Epoxy
PLus glue
 Elevatorpushrod install assame asthe way
of aileron pushrod.
Elevator
control horn
ELEVATOR PUSHROD INSTALLATION.
M2
M2 lock nut.
C/A glue.
Elevatorpushrod
Bottom side
Elevatorpushrod
Plastic parts top side of pushrod.
Cut.

18
BEDE BD-5J Item code: BH139 . Instruction Manual
RUDDER INSTALLATION.
Cut.
See picture below:
Cutthe covering
awayfromtheslot.
Temporary pin to
keep hinge centered.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
bend90
degree.
Elevator
pushrod

19
BEDE BD-5J Item code: BH139 . Instruction Manual
Rudder servo install as same as method of
elevatorservo.
Rudderservo
Top side.
2x10mm.
Secure.
Rudder control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
RUDDER CONTROL HORN INSTALLA-
TION.
ControlhornofRudder.
Rudder servo
Electric wire.
servo tray

20
BEDE BD-5J Item code: BH139 . Instruction Manual
Control horn
Rudder.
RUDDER PUSHROD INSTALLATION.
 Rudder pushrod install as same as the way
of aileron pushrod.
30mm.
Rudder
pushrod.
Seepicture below:
INSTALLING RETRACT SERVO NOSE
GEAR.
A+B Epoxy
PLUS glue
Retract servo
nose gear
Rudderpushrod
Top side.