BlueSpot 07912 User manual

15 PCE
AIR DIE GRINDER SET
User Manual
07912

01
Thank you for purchasing a BlueSpot product, you can find further information
on our range at www.BlueSpot.uk.com. Please ensure that you are using the
product correctly and that all guidance and cautions are followed in accordance
with the instructions. Please retain these instructions for future reference.
General Information
Please make sure that you read these instructions carefully in order to avoid injury when
using the BlueSpot 15 PCE Air Die Grinder Set. Follow all health and safety rules and
regulations. If in doubt and available please contact a more knowledgeable source.
DO NOT use if damaged.
• ALWAYS ensure you have read through all of the instructions and fully understand how
to operate the tool before beginning.
• ALWAYS check the air die grinder set for any damage before use. Any damage found
needs to be repaired or replaced before use to prevent damage to property or personal
injury.
• ALWAYS check the air hose for any damage before use. Any damage found needs to be
repaired or replaced before use to prevent damage to property or personal injury.
• ALWAYS dress appropriately – clothing should be close fitted and long hair tied back.
Jewellery should be removed and shoes should be worn with a non-slip sole.
• ALWAYS wear the correct PPE equipment. Approved eye protection should always
be worn.
• ALWAYS ensure you work in a well ventilated room.
• ALWAYS check for missing or damaged parts before use.
• Maintain tool in good and clean condition for best and safest performance.
• Keep the work area clean, uncluttered and ensure there is adequate lighting.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip
shoes.
• Keep children and unauthorised persons away from the work area.
• ALWAYS ensure the trigger is off before connecting the tool to the air supply.
• ALWAYS ensure any adjusting keys or wrenches have been removed before turning the
tool on.
• ALWAYS ensure your workpiece is secure before operation.
Safe use
• ALWAYS ensure the air hose has been disconnected from the tool correctly before
making any adjustments, changing accessories or storing the tool. Squeeze the lever to
release all the compressed air in the tool.
• ALWAYS ensure that clean, dry, regulated, compressed air is used at 90PSI. Do not
exceed 90PSI as this can be very dangerous.
• BE AWARE that before connecting the tool to the air supply air tool oil should be added
into the air inlet fitting of the die grinder before each use.
• ALWAYS store the air die grinder set away correctly when not in use.
• DO NOT allow untrained persons to use the kit.
• DO NOT operate the tool if you are tired as this could be dangerous.
• NEVER operate the tool if you are under the influence of drugs or alcohol as this
is dangerous.
• DO NOT make modifications to the air die grinder set.
• NEVER use the air die grinder set to perform a task it was not designed to do.
• NEVER use oxygen, carbon dioxide, combustible gases or other bottled gas with the
tool.
• ALWAYS stop using the tool straight away if you start to experience discomfort or pain.
Consult with a qualified health professional if needed.
• If the Air Die Grinder Set is damaged do not use.

Maximum Air Pressure
Air Consumption
Air Inlet
Maximum RPM
90PSI Recommended
90PSI
¼”
22000 RPM
Please make sure that you read these instructions carefully in order to avoid injury when
using the BlueSpot 15 PCE Air Die Grinder Set. Follow all health and safety rules and
regulations. If in doubt and available please contact a more knowledgeable source.
DO NOT use if damaged.
• ALWAYS ensure you have read through all of the instructions and fully understand how
to operate the tool before beginning.
• ALWAYS check the air die grinder set for any damage before use. Any damage found
needs to be repaired or replaced before use to prevent damage to property or personal
injury.
• ALWAYS check the air hose for any damage before use. Any damage found needs to be
repaired or replaced before use to prevent damage to property or personal injury.
• ALWAYS dress appropriately – clothing should be close fitted and long hair tied back.
Jewellery should be removed and shoes should be worn with a non-slip sole.
• ALWAYS wear the correct PPE equipment. Approved eye protection should always
be worn.
• ALWAYS ensure you work in a well ventilated room.
• ALWAYS check for missing or damaged parts before use.
• Maintain tool in good and clean condition for best and safest performance.
• Keep the work area clean, uncluttered and ensure there is adequate lighting.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip
shoes.
• Keep children and unauthorised persons away from the work area.
• ALWAYS ensure the trigger is off before connecting the tool to the air supply.
• ALWAYS ensure any adjusting keys or wrenches have been removed before turning the
tool on.
• ALWAYS ensure your workpiece is secure before operation.
02
The BlueSpot 15 PCE Air Die Grinder Set is ideal for grinding and polishing a range of
materials. The set comprises: 1x mini air die grinder, 2 x hand wrenches, 1 x 3mm (1/8")
collet, 5 x 1/4"(6mm) shank grinding stones, 5 x 3/8"(3mm) shank grinding stones, 1 x
nipple.The set is supplied in a useful, blow molded, plastic carry case.
Safe use (continued)
• ALWAYS ensure the air hose has been disconnected from the tool correctly before
making any adjustments, changing accessories or storing the tool. Squeeze the lever to
release all the compressed air in the tool.
• ALWAYS ensure that clean, dry, regulated, compressed air is used at 90PSI. Do not
exceed 90PSI as this can be very dangerous.
• BE AWARE that before connecting the tool to the air supply air tool oil should be added
into the air inlet fitting of the die grinder before each use.
• ALWAYS store the air die grinder set away correctly when not in use.
• DO NOT allow untrained persons to use the kit.
• DO NOT operate the tool if you are tired as this could be dangerous.
• NEVER operate the tool if you are under the influence of drugs or alcohol as this
is dangerous.
• DO NOT make modifications to the air die grinder set.
• NEVER use the air die grinder set to perform a task it was not designed to do.
• NEVER use oxygen, carbon dioxide, combustible gases or other bottled gas with the
tool.
• ALWAYS stop using the tool straight away if you start to experience discomfort or pain.
Consult with a qualified health professional if needed.
• If the Air Die Grinder Set is damaged do not use.
Introduction
Specification

03
Specification
1. 1x mini air die grinder
2. 5 x 1/4"(6mm) shank grinding stones
5 x 3/8"(3mm) shank grinding stones
3. 1 x 3mm(1/8") collet
4. 2 x hand wrenches
1
2
3
4
Parts Diagram
1. Cover
2. Air Inlet
3. Air Inlet Seat
4. Body
5. Pin
6. Trigger
7. Pin
8. Plug
9. Switch Seal Cap
10. Spring
11. Washer
12. Switch Screw Cap
13. Rotor
14. End Plate
15. Rotor
16. Blade
17. Cylinder
18. O-ring
19. Front Plate
20. Bearing
21. Retainer
22. Housing Cup
23. Collect Holder
24. Collect
25. Collect Cap

04
Operation
ALWAYS ensure you have read through all of the safety precautions and instructions before
using the tool and that you feel confident operating the tool.
BE AWARE that before connecting the tool to the air supply air tool oil should be added into
the air inlet fitting of the die grinder before each use.
1. Attach the quick connector into the air inlet of the die grinder. To ensure a tight
connection use PTFE tape around the thread of the quick connector and then tighten
the quick connector into the air inlet. Ensure there is a secure connection.
2. Attach the collet into the spindle on the die grinder.
3. Find the appropriate grinding stone for the workpiece.
4. Attach the grinding shank fully into the collet.
5. The collet nut (on the spindle) may need retightening with the hand wrench. This will
secure the collect and grinding stone together.
6. Connect the air supply hose to the quick connector.
7. Turn on the air compressor and set the regulator to 90PSI. DO NOT exceed 90PSI.
BE AWARE of where the air hose is positioned and that it does not cause a tripping
hazard.
8. Ensure you have a secure grip on the die grinder and hold with both hands.
9. Safely push the lever forward to release the throttle lever and gently press the lever.
10. Changing the pressure on the lever will increase/decrease the speed on the die grinder.
Note – The die grinder always turns the grinding stone in a clockwise rotation.
11. Gently apply the grinding stone to the workpiece. Slowly move the grinding stone to the
left and right.
12. Release the lever when you have completed.The safety will automatically return to the
locked position when the lever is fully released.
13. Turn off the air compressor.
14. Squeeze the lever to release all the compressed air in the tool.
15. Disconnect the air hose from the die grinder.
16. Remove the grinding stone from the die grinder.
17. Store the air die grinder set in a cool dry area that is out of reach of children.

05
ContactDistance to Spot SizeDisposal
Clean the tool with a dry cloth if needed.
Cleaning & Maintenance
ContactDistance to Spot SizeDisposal
Store the air die grinder set in a cool dry area that is out of reach of children.
Storage
ContactDistance to Spot SizeDisposal
Cleaning & Maintenance
Notes
ContactDistance to Spot SizeDisposal
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and
packaging should be sorted, taken to a recycling centre and disposed of in a manner which is
compatible with the environment. When the product becomes completely unserviceable and
requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Environmental Protection
Always check and adhere to national regulations when disposing of any tools that are no longer
functional and cannot be repaired.
• Contact your local waste disposal authority for information on how to correctly
dispose of tools.
Disposal
Contact
Find out more about the BlueSpot® Lifetime Guarantee at www.BlueSpot.uk.com
Tel: [phone]
Email: [email protected]
Orme Business Centre, Greenacres Road,
Oldham, OL4 3NS