BOERPLAY Detached Slide 0.8-0.93m 0.8 - 0.93m User manual

Detached Slide 0.8-0.93m 0.8 -
0.93m
PSTE000.230
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 230
A
Glijbaan
Vrijstaand 1,0 m
13-7-2023
Hoofdafmetingen Main dimensions
2,10 m
> 0,35 m
0,90 m
0,00 m
0,93 m
1,68 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 230
A
Glijbaan
Vrijstaand 1,0 m
13-7-2023
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
3,90 m
5,09 m
4,59 m
R1,50m
0,96 m0,50 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 230
Glijbaan
Vrijstaand 1,0 m
13-7-2023
Bodemplan Groundplan
A
0,76 m
0,60 m
0,75 m
0,25 m
2,00 m
1,00 m
1,41 m
0,18 m
1,68 m
1,95 m
1,95 m
Grondmarkering
Ground level marker

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 230
Glijbaan
Vrijstaand 1,0 m
13-7-2023
Montage Mounting
A
Geleverde delen:
A - ladder
B - glijbaan
Bevestiging sets:
1 - slotbout M10 incl moer en ring (6x)
Montagevolgorde:
1 - monteer A aan B met set 1 op de voorgeboorde gaten
2 - graaf de gaten volgens het bodemplan en plaats hierin het toestel
3 - controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
4 - dicht de gaten en verdicht het zand
Controles:
1 - correcte opbouw en alle bevestigingsmiddelen
2 - de uiterste hoogte van het uiteinde van de glijbaan (<19 cm)
3 - de lengte van het startplatform (35>40 cm)
4 - controleer de afmetingen van de valbodem t o v het toestel
Supplied parts:
A - ladder
B - slide
Mounting kits:
1 - M10 bolt with washer and lock nut (6x)
Assembly sequence:
1 - mount part A to B using set 1 on the pre-drilled holes
2 - dig the holes according to the ground plan and place the play equipment
3 - check that the equipment conforms to the dimensions shown on sheet 'dimensions'
3 - close the holes and compact the sand
Checks:
1 - correct assembly and all the fasteners
2 - the maximum height of the end of the slide (<19 cm)
3 - the minimum length of the starting platform (35>40 cm)
4 - check the dimensions of the safety area compared to the play equipment
Typeplaatje
Identification plate
B
B
A

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 230
Glijbaan
Vrijstaand 1,0 m
13-7-2023
Modules Modules
A
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
93 cm
Trap glijbaan
B
199002PSTMO11
1

LOGBOOK
Type indication Adventure Play
Article number PSTE000.230
Product Name Detached Slide 0.8-0.93m 0.8 - 0.93m
Maximum fall height 1,0 m
Construction year 2024
Certificate 033859
Inspection body TUV Nederland QA BV
Ekkersrijt 4401
5692 DL Son
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

B ( 1 : 18 )
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type
#
Nr.
M12, L= 160, RVS A2-70
Draadeind+borgm.+ringen+dop
160M12SET
MR41
M12, L= 180, RVS A2-70
Draadeind+borgm.+ringen+dop
180M12SET
MR4
2
5 x 70 - RVS A2-70
Schroef Assy
070005002SR123
ORG RVS M10DOPMOER 020010011SR6
4
ø10 X 50 - RVS A2-70
Houtdraadbout
050010022SR2
5
M10 x 60 - RVS A2-70
Slotbout
065010026SR66
M10SLUITRING 002010030SR87
M10 - RVS A2-70Veerring groot 002010032SR68
Donut zwart
eschermdop M10-M12 060010DONKST29
Dop zwart
eschermdop M10-M12
060010DOPKST210
Lengte =900
Paal 6
009080PSTOHO211
Lengte =2500
Paal 10-12
025120PSTOHO212
Lengte = 1000
Standaard plank 120x20
100211PSTOHO313
GlijbaanStartbordes
230003PSTSHO
114
93 cm
Glijbaan
G320611
VR
SME
115
B
© Copyright BOERplay 13-7-2023 Revision: B MOD PST 002 199
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
0
768
1031
1602
2520
Openingen tussen treden
en bordes controleren,
tenminste Ø230 mm
Positie controleren icm
met glijbaan en V-probe.
11
13
12
15
14
5 7 9 10
3
6
4
8
7
13
2
Powered by TCPDF (www.tcpdf.org)