BOERPLAY Double Swing H2.12 User manual

Double Swing Anti-wrap H2.12
BBPE030.9K
Powered by TCPDF (www.tcpdf.org) 1 / 1

© Copyright BOERplay 29-11-2023 Revision: A BBP 030 9K
main dimensions
Hoofdafmetingen
Hauptabmessungen
Dimensiones principales
Dimensions principales
NL
DE
ES
FR
0,00 m
2,04 m
2,18 m
0,00 m
0,69 m
1,40 m
0,00 m 0,43 m 1,06 m 2,29 m 2,91 m 3,34 m
>0,35 m
>0,35 m

© Copyright BOERplay 29-11-2023 Revision: A BBP 030 9K
obstacle free zone
Obstakelvrije zone
Hindernissfreie raum
Zona libre de obstáculos
Zone libre d’obstacles
NL
DE
ES
FR
7,50 m 6,50 m
4,00 m
3,00 m
2,00 m
Impact area
NL
DE
ES
FR
Obstacle free zone
NL
DE
ES
FR
i
Opvangzone
Ausprallbereich
Zona de impacto
Zone d‘impact
Obstakelvrije zone
Hindernissfreie raum
Zona libre de obstáculos
Zone libre d’obstacles

© Copyright BOERplay 29-11-2023 Revision: A BBP 030 9K
ground plan
Bodemplan
Bodenplan
Plan de superficie
Plan de surface
NL
DE
ES
FR
Grondmarkering
Ground level marker
0,55 m
2,96 m1,56 m2,97 m
0,30 m 3,41 m 0,30 m

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
Boer Basic playAW Schommel
BK533BBPMOD11
Overgooi Zitje 1,5 m
Basic Play
538
BBP
MOD
1
2
Peuterzitje lengte 1.5 mMulti Swing
680
BBP
MOD
1
3
© Copyright BOERplay 29-11-2023 Revision: A BBP 030 9K
order of assembly
Montagevolgorde
Montagereihenfolge
Orden de esemblado
Ordre de montage
NL
DE
ES
FR
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zijn bemaat op de bovenkant (klim anden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Bou 1,2,3 op uit de staanders en ligger
3 - Plaats Schommel
4 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
5 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbou en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions sho the specific dimensions of the connections
- The modules hich contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing alls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Assemble 1,2,3 out of the posts and horizontal beam
3 - Place S ing
4 - Check that the equipment conforms to the dimensions sho n on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area ith regard to the play equipment
Typeplaatje
Identification plate
B
3
2
1

LOGBOOK
Type indication Basic Play
Article number BBPE030.9K
Product Name Double Swing Anti-wrap H2.12
Maximum fall height 1,4 m
Construction year 2023
Certificate 136145
Inspection body Keurmerkinstituut
Groeneweg 2e, Zoetermeer
2718AA Zoetermeer
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 533 K B
AW Schommel
Boer Basic play
10-10-2017
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
5 x 50 - RVS A2-70
Schroef Assy
050005002BSR201
M10 - VZ 8.8Bor moer 010010010BSV52
M10 - VZ 8.8
Zeskantmoer
008010017BSV163
M10 x 100 - VZ 8.8Zeskantbout ISO 4014 100010021BSV
54
M10 x 145 - VZ 8.8
Slotbout
145010026BSV12
5
M10 x 135 - VZ 8.8
Slotbout
135010026BSV46
M10 VZSLUITRING 002010030BSV267
M10 - VZ 8.8Veerrin 002010034BSV168
Basic PlayStaander schommel
027
BBP
KST
4
9
Donut wit
Beschermdop M10-M12
020010DONKST1610
Donut zwart rondin 100Beschermdop M10-M12
060110DONKST1011
Dop wit
Beschermdop M10-M12 020010DOPKST1612
Dop zwart
Beschermdop M10-M12
060010DOPKST1013
AluminiumPaalkap 100x100
B502100KAPOME414
100 x 100
Voetplaat
CVZP903VRBOME415
Basic PlaySchommelpaneel
A061007BBPOPE216
Anti-over ooischommelBovenbalk 038
BBP
SME
117
Anti-over ooischommelEindstuk bovenbalk
039
BBP
SME118
17
18
15
9
1
2 4 7 7 11 11 13 13
16
14
1
3 6 78 10 12
3 5 7 8 10 12

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
M10 - RVS A2-70Borgmoer 010010010BSR21
M10 x 70 - RVS A2-70
Zeskantbout
070010021BSR22
M10SLUITRIN 002010030BSR63
RVS A2-70
Schommelscharnier
090012081BSR2
4
Peuterzitje
Peuterschommel
B 001HUCDRD15
BBP Schommel
Lagerring 026BBPKST26
Donut zwart
Beschermdop M10-M12
060010DONKST47
Dop zwart
Beschermdop M10-M12
060010DOPKST
4
8
Schommel dubbelUBP Schommelbuis
D
916200
UBP
SME
1
9
© Copyright BOERplay 28-3-2022 Revision: MOD BBP 680 G
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
9
5
9
4
8723 8 7 1 3
6
1688
1490

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 538 G
Basic Play
Overgooi Zitje 1,5 m
1-10-2015
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
M10 - RVS A2-70
Borgmoer
010010010BSR2
1
M10 70 - RVS A2-70
Zeskantbout
070010021BSR22
M10SLUITRING 002010030BSR63
RVS A2-70
Schommelscharnier
090012081BSR24
Zwart
Zitje CNK + bevm
ZWT101ZITCNK15
BBP Schommel
Lagerring
026
BBP
KST26
Donut zwart
Beschermdop M10-M12
060010DONKST
47
Dop zwart
Beschermdop M10-M12 060010DOPKST
4
8
Met vork 1,45 mSchommelketting 5mm
145
005
KETRNT
29
Schommel dubbelUBP Schommelbuis
D
916200
UBP
SME110
8
2
3
7
8137
6
10
4
5
9
Powered by TCPDF (www.tcpdf.org)