BOERPLAY MNPE501.001 User manual

Sandpit with sliding cover
MNPE501.001
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE MNP 501 001
Schuifzandbak
Mini Play
1-3-2017
Hoofdafmetingen Main dimensions
0,00 m
0,15 m
0,30 m
0,35 m
0,41 m
0,45 m
0,59 m
0,00 m 0,07 m 4,44 m 4,50 m
0,00 m
0,04 m
0,12 m
2,30 m
2,38 m
2,42 m
1,90 m
2,10 m
doorgraafbeveiliging aanbrengen
X
X bij gesloten stand altijd < 100
X at closed position always < 100
0,06 m
0,04 m
0,26 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE MNP 501 001
Schuifzandbak
Mini Play
1-3-2017
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
7,46 m
R1,50m
5,41 m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE MNP 501 001
Schuifzandbak
Mini Play
1-3-2017
Bodemplan Groundplan
0,40 m
0,08 m
2,68 m 2,10 m 2,68 m
1,65 m2,10 m1,65 m
0,26 m
1,13 m
0,12 m
Grondmarkering
Ground level marker

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE MNP 501 001
Schuifzandbak
Mini Play
1-3-2017
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
Mini PlayDeksel zandbak
A
030049
MNP
MOD21
Mini Play
Slot schuif zandbak
001050
MNP
MOD22
Schuifzandbak
Rebo bak 068255
MNP
MOD
1
3
Mini PlayGeleiding schuifzandbak
069255
MNP
MOD2
4
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zi n op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zi n bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Plaats 3
3 - Plaats 4(2x), verbind deze aan 3
4 - Plaats 1(2x), verbind deze aan 4
5 - Plaats 2(2x), verbind deze aan 1(2x)
6 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
7 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel°
3 - Controleer of er doorgraafbeveiliging aanwezig is.
4 - Controleer opening tussen deksels in gesloten stand alti d kleiner is dan 100 mm.
5 - Controleer bi sleuteloverdracht, of sleutelbeheer is vastgelegd.
Zandbak mag alleen gebruikt worden wanneer de deksels zi n vastgezet.
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 3
3 - Place 4(2x), attach it to 3
4 - Place 1(2x), attach it to 4
5 - Place 2(2x), attach it to 1(2x)
6 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
7 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
3 - Check if digging is not possible
4 - Check opening between lids closed always smaller than 100 mm
5 - Check with key transfer, ik key management is captured
Sandpit should only be used when the covers are locked
1
34
Typeplaatje
Identification plate
B
2

LOGBOOK
Type indication Basic Play
Article number MNPE501.001
Product Name Sandpit with sliding cover
Maximum fall height 0,5 m
Construction year 2023
Certificate 058743
Inspection body TUV Nederland QA BV
Ekkersrijt 4401
5692 DL Son
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

A ( 1 : 4 )
B ( 1 : 4 )
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD MNP 049 030 A
Deksel zandbak
Mini Play
21-5-2019
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
5 x 50 - RVS A2-70
Schroe Assy
050005002BSR81
4,8 x 30 - RVS A2-70
Klinknagel bolkop
053005014BSR282
M10 x 20 - RVS A2-70
Verzonken bout
020010024BSR83
M10 - VZ 8.8
Borgmoer
010010010BSV10
4
M10 x 140 - VZ 8.8
Zeskantbout ISO 4014
140010021BSV2
5
M10 x 120 - VZ 8.8Zeskantbout ISO 4014 120010021BSV26
M10 x 80 - VZ 8.8Zeskantbout ISO 4014 080010021BSV
47
M10 x 220 - VZ 8.8
Zeskantbout ISO 4014
220010021BSV68
M10 x 60 - VZ 8.8
Houtdraadbout
060010022BSV89
M10 VZSLUITRING 002010030BSV3210
M10 - VZ 8.8Veerring 002010034BSV411
Kunststo wit
Handgreep 402183310KST212
84395000012
interplay donut M10 wit
020011DONKST3213
84395000014
interplay dop M10 wit
020011DOPKST3214
Zandbak
Schui deksel
B030491MNPOPE115
Schui zandbakPlaat
B030492MNPOPE216
Schui zandbakPlaat
030493
MNP
OPE
417
Schui zandbakPlaat
B
030494
MNP
OPE218
Schui zandbak
Dekselbalk 140
454MNP
ORE219
Schui zandbak
Aanslagbalk 080
455MNP
ORE
1
20
Schui zandbakFrame deksel
A
304140
MNP
SME121
A
B
15
7
14
11
10
13
12
5
21 20
6 14 10 13 13 10 4 14
1
13
9
10
14
814 10 13 13 10 4 14
3
15
16
18
19
2

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD MNP 255 069
Geleiding schuifzandbak
Mini Play
1-3-2017
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
5 x 50 - RVS 2-70
Schroef ssy
050005002BSR
4
1
M10 - RVS 2-70Borgmoer 010010010BSR62
M10 x 150 - RVS 2-70
Slotbout
150010026BSR23
M10 x 170 - RVS 2-70
Slotbout
170010026BSR44
M10SLUITRING 002010030BSR6
5
Rond 36Meubeldop
090036DOPKST66
UkkepukVoetplaat
BVZP
615
UKP
OME2
7
Schuif zandbak
Staander 080458
MNP
ORE28
ZandbakGeleiding
320142
MNP
SME19
452 6
8
1
7
9
3
2
5
6

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD MNP 255 068
Rebo bak
Schuifzandbak
27-2-2017
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
M10 - VZ 8.8
Zeskantmoer
008010017BSV11
M10 VZSLUITRING 002010030BSV12
M10 - VZ 8.8Veerring 002010034BSV13
Rond 3Meubeldop
09003DOPKST1
4
Zandbak
Ligger
100
457MNP
ORE1
5
Zandbak
Ligger
1004 1
MNP
ORE2
Zandbak
Ligger
1004 2
MNP
ORE2
7
Schuif zandbakDraadeind M10 incl. moer
372141
MNP
SME18
5
8
2
3
1
4
6
7

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD MNP 050 001
Slot schuif zandbak
Mini Play
27-3-2017
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
ZandbakHangslot
000000SLTSM
11
5 x 50 - RVS A2-70
Schroef Assy
050005002SR22
5 x 70 - RVS A2-70
Schroef Assy
070005002SR
4
3
Ketting
eugel 008HUC
DRD
3
4
0,32 m langRVS ketting 5mm
032002005
KET
1
5
1
34
5
Powered by TCPDF (www.tcpdf.org)