BOERPLAY PSTE105.036 User manual

Climbing equipment
PSTE105.036
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 105 036
Klauter & Duikel
Adventure Play
11-7-2023
Afmetingen Dimensions
C
0,00 m
0,69 m
4,12 m
4,77 m
0,00 m 0,57 m 2,95 m 3,01 m 3,50 m 4,41 m
2,37 m
1,17 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 105 036
Klauter & Duikel
Adventure Play
11-7-2023
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
C
8,19 m
7,25 m
>1,50m
>1,50m
0,50 m
>1,50m
>1,50m
>1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 105 036
Klauter & Duikel
Adventure Play
11-7-2023
Bodemplan Groundplan
C
1,51 m 1,45 m 2,63 m 1,08 m 1,51 m
1,47 m 1,09 m 2,06 m 1,26 m 1,80 m
1,24 m 1,06 m
4,94 m 1,21 m 1,51 m
0,70 m
rondmarkering
Ground le el marker
1800
1791
864
1400
1398

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 105 036
Klauter & Duikel
Adventure Play
11-7-2023
Modules Modules
C
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
Module tbv toestel
D
036105PSMOD11
1
Typeplaatje
Identification plate
B
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met bui en ijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules ijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Plaats staanders
2 - Plaats verbindingsbalken
3 - Plaats overige onderdelen
4 - Controleer of het toestel voldoet aan de afmetingen oals op blad 'afmetingen'
5 - Dicht de gaten en verdicht het and
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Place poles
2 - Place Beams
3 - Place other parts
4 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area with regard to the play equipment
123

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 105 036
Klauter & Duikel
Adventure Play
11-7-2023
Afmetingen Dimensions
C
0,80 m 0,28 m 0,84 m 0,25 m
0,43 m
0,00 m
0,77 m
1,14 m
1,30 m
2,30 m
2,39 m
0,00 m
0,77 m
1,14 m
1,30 m
2,39 m
Touwen strak
Tighten ropes

LOGBOOK
Type indication Adventure Play
Article number PSTE105.036
Product Name Climbing equipment
Maximum fall height 1,3 m
Construction year 2023
Certificate 038624
Inspection body TUV Nederland QA BV
Ekkersrijt 4401
5692 DL Son
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 105 036
Module tbv toestel
11-7-2023
Samenstelling module Assembly module
D
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
M12, L= 300, RVS A2-70
Draadeind+borg .+ringen+dop
300M12SETBMR51
M12, L= 260, RVS A2-70
Draadeind+borg .+ringen+dop
260M12SETBMR32
M12BORGMOER 012012010BSR83
Ø10 X 80 - RVS A2-70Houtdraadbout 080010022BSR28
4
M12 - RVS A2-70
Sluitring
003012030BSR8
5
5 MM RVS
D-sluiting
000005031BSR86
Dop zwart
Bescher dop M10-M12
060010DOPKST87
KUNSTSTOFRING 008005RNGKST88
Lengte =2000
Paal 14-16
020160PSTOHO
1
9
Lengte =3000
Paal 14-16
030160PSTOHO110
Lengte =1700Paal 14-16 017160PSTOHO2
11
Lengte =1600Paal 14-16 016160PSTOHO
1
12
Lengte =3100
Paal 14-16
031160PSTOHO213
Lengte =4600
Paal 14-16
046160PSTOHO114
Lengte =2100
Paal 14-16
021160PSTOHO115
Lengte =2800
Paal 14-16
028160PSTOHO116
Lengte = 1400Standaard plank 120x20 140211PSTOHO2
17
Lengte = 1200
Standaard plank 120x20
120211PSTOHO218
Lengte = 1800
Standaard plank 120x20
180211PSTOHO119
Lengte = 1100
Standaard plank 120x20
110211PSTOHO120
Lengte = 1600
Standaard plank 120x20
160211PSTOHO121
160 dia eter
Touw 3,6
B
002160PSTONT
1
22
M12x150
Slotbout et lip
150088PSTSME823
DIAGONAALSYSTEEMBUIS
D
320022
VRB
SME
1
24
Adventure PlayHandtouw 302016PSTSNT
1
25
Adventure PlayVerbindingsnet
303016PSTSNT126
Pagina 1 van 2
15
20 17
20 11 17
16
13 26 14 10 24 9
19
13
21
18 12
11 18 22 25
3 5 67 8 23
4
1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 105 036
Module tbv toestel
11-7-2023
Samenstelling module Assembly module
D
0,00 m
0,80 m
1,26 m
1,70 m
2,99 m
3,06 m
0,00 m
1,15 m
1,31 m
1,38 m
1,84 m
2,83 m
3,08 m
0,00 m
1,31 m
1,70 m
2,44 m
2,83 m
2,97 m
3,07 m
0,00 m
0,99 m
1,92 m
2,99 m
Pagina 2 van 2
Powered by TCPDF (www.tcpdf.org)