BOERPLAY SOLE030.105 User manual

SOLE030.105
Giant Swing

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 105 A
Giant Swoeng
22-12-2014
Afmetingen Dimensions
0,00 m
4,01 m
4,15 m
4,44 m
6,01 m
3,44 m
>0,35 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 105 A
Giant Swoeng
22-12-2014
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
10,75 m
7,15 m
4,58 m
3,38 m
9,75 m
9,02 m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 105 A
Giant Swoeng
22-12-2014
Bodemplan Groundplan
0,70 m
0,43 m 6,29 m 0,43 m
3,48 m
3,80 m3,48 m
0,43 m
0,43 m
rondmarkering
Ground le el marker

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE SOL 030 105 A
Giant Swoeng
22-12-2014
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
KETTING 3,45 M
Schommelzitje
356030SOLMOD21
MET L DUBBELSCHOMMELFR ME 001
369
SOLMOD12
12
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoo dmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven speci iek de maten van de verbindingen aan
- De modules met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graa de gaten volgens het bodemplan
2 - Plaats 2
3 - Plaats 1(2x) en verbind deze aan 2
4 - Controleer o het toestel voldoet aan de a metingen zoals op blad 'a metingen'
5 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de a metingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions o the posts and loors
- The detailed dimensions show the speci ic dimensions o the connections
- The modules which contain tubes are dimensioned at the top o the langes
- Other modules are dimensioned at the top (climbing walls, caps or the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 2
3 - Place 1(2x) and attach it to 2
4 - Check that the equipment con orms to the dimensions shown on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the asteners
2 - Check the dimensions o the sa ety area with regard to the play equipment
Typeplaatje
Identification plate
B

LOGBOOK
(Onderstaand logboek kan gebruikt worden om te voldoen aan de eisen, gesteld in artikel 14 van het Warenwetbesluit Attractie- en Speeltoestellen)
Type indication Classic Play
Product code SOLE030.105
Name of equipment Giant Swoeng
Maximum height of fall 2,3 m
Year of construction 2017
Certificate 3200116225
inspection authority Liftinstituut B.V.
Buikslotermeerplein 381, A'dam - 1025 XE Amsterdam
Name manufacturer BOERplay
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
name installer
Description of equipment Giant Swing
Location of equipment
Data about the owner of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
Data about the administrator of the play equipment
Name:
Address:
Postcode and town:
Contact person:
Telephone number:
SOLE030.105
Giant Swing

LOGBOOK
Inspection and maintenance intervals
Nr.
Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and missing parts.
Inspect bolts, screws and nuts for absence, jams, corrosion
and wear.
Add missing parts, secure joints, apply missing fixing
agent and replace corroded parts.
1
2
Chec suspension for wear. Replace worn parts and/or remove non-functioning
parts.
1
3
Inspect rotating parts such as hinges, rolling-element
bearings, etc. for wear and acceptability.
Replace worn parts and/or remove non-functioning
parts.
1
4
Chec wood for splinters, unacceptable damage and signs of
rot. Especially at ground level.
Repair damage. Replace affected wood. Smoothen
splintered wood and sharp edges.
1
5
Inspect foundation for stability, tearing and coverage. Restore foundation and covering material.
3
6
Examine rubber and synthetic parts for wear, damage and
brea . Replace original parts.
3
7
Inspect metal for corrosion and damage in the coating. Restore any damaged coating (after removing rust and
applying primer).
6
Chec ropes, cables, chains and nets for wear and damage.
Steel cables and nets which are tensioned must be chec ed
for tension.
Replace parts where necessary. Steel cables and nets
must be tensioned.
3
9
Inspect equipment for unsafe changes and additions. Remove unsafe additions and correct unsafe changes.
1
10
Inspect safety surfaces. Restore and repair where necessary.
1
Remarks
1. If used intensively, all points require extra attention.
2. Extreme weather conditions and locations may require a higher inspection frequency. Discuss this with
the supplier.
3. Vandalism-sensitive locations require stricter inspections, possibly daily.
4. Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly.
Examples are poisonous plants, glass shards, etc. Frequency depends on strain.
5. Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area.
6. Replacement parts can be ordered at the manufacturer with the part numbers on the module drawing.
Drawings can be found in de user guide.
7. The impact area shall be provided with impact attenuating surface according to the specified falling
height.
. This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7".

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 030 356 A
Schommelzitje
Ketting 3,5 m
3-3-2015
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
OpmerkingBenamingRev.Bew.VolgnrProgr.Type
#
Nr.
BORG RVS M10DOPMOER 020010011BSR1
M10 x 170 - RVS A2-70Zeskantbout 170010021BSR 2
M10 - RVS A2-70
Sluitring
002010030BSR123
RVS A2-70
Schommelscharnier
091012081BSR2
Donut RoodBeschermdop M10-M12
030010DONKST5
Dop roodBeschermdop M10-M12
030010DOPKST6
Zitje incl. ketting
090350
ZIT
SMD
17
M8 x 25 - RVS A2-70
Zeskantbout
025008021BSR 7.1
M8 - RVS A2-70Sluitring 016008030BSR 7.2
Zwart
Schommelzitje CNK 090001
ZIT
CNK
1
7.3
Met vork 3,5mSchommelketting 5mm
350005
KETRNT
2
7.
6
2
3
5
4
3
1
7.4
7.3 7.2 7.1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD SOL 369 001
SCHOMMELFRAME
GIANT
12-10-2017
Samenstelling module Assembly module
OpmerkingBenamingRev.Bew.Volgnr.Progr.Type
#
Nr.
M10 - RVS A2-70Borgmoer 010010010BSR21
M12 - RVS A2-70
Dopmoer
025012012BSR122
M10 x 25 - RVS A2-70
eskantbout
025010021BSR23
M12 x 130 - RVS A2-70
eskantbout
130012021BSR124
M10SLUITRING 002010030BSR45
M12 - RVS A2-70
Sluitring
003012030BSR246
Donut RoodBeschermdop M10-M12
030010DONKST16
7
Dop roodBeschermdop M10-M12
030010DOPKST168
GIANTSCHOMMELBUISC372108SOLSME
1
9
GIANTSTAANDER LINKS
A
372109SOLSME210
GIANTSTAANDER RECHTS
A
372110SOLSME211
8 6 74 6 2
73 8 5
71
8
59
1110