BOERPLAY Springer beam User manual

Springer beam
PSTE000.145
Powered by TCPDF (www.tcpdf.org) 1 / 1

© Copyright BOERplay 21-2-2022 Revision: B PST 000 145
main dimensions
Hoofdafmetingen
Hauptabmessungen
Dimensiones principales
Dimensions principales
NL
DE
ES
FR
0,57 m
0,00 m 0,50 m 2,50 m 2,99 m
0,00 m
0,19 m
0,37 m
Uiteinden Afronden met > R20 (2x)

© Copyright BOERplay 21-2-2022 Revision: B PST 000 145
obstacle free zone
Obstakelvrije zone
Hindernissfreie raum
Zona libre de obstáculos
Zone libre d’obstacles
NL
DE
ES
FR
6,50 m
3,50 m
R1,75m
R1,75m

© Copyright BOERplay 21-2-2022 Revision: B PST 000 145
ground plan
Bodemplan
Bodenplan
Plan de superficie
Plan de surface
NL
DE
ES
FR
0,5 m
0,48 m
2,00 m2,25 m 2,25 m
17501750
Grondmarkering
Ground level marker

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type
#
Nr.
Adventure PlayVeerbalk
031006PSTMOD
11
Onderstel
Veerstier
131006PSTMOD22
© Copyright BOERplay 21-2-2022 Revision: B PST 000 145
order of assembly
Montagevolgorde
Montagereihenfolge
Orden de esemblado
Ordre de montage
NL
DE
ES
FR
2
1
2
Typeplaatje
Identification plate
B

© Copyright BOERplay 21-2-2022 Revision: B PST 000 145
order of assembly
Montagevolgorde
Montagereihenfolge
Orden de esemblado
Ordre de montage
NL
DE
ES
FR
Geleverde delen:
A - veerelement met onderstel
Bevestiging sets:
1 - n.v.t.
Montagevolgorde:
1 - graaf de gaten volgens het bodemplan en plaats hierin het toestel
2 - controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
3 - dicht de gaten en verdicht het zand
ontroles:
1 - correcte opbouw en alle bevestigingsmiddelen
2 - controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied parts:
A - rocking-element with support
Mounting kits:
1 - n.a.
Assembly sequence:
1 - dig the holes according to the ground plan and place the play equipment
2 - check that the equipment conforms to the dimensions shown on sheet 'dimensions'
3 - close the holes and compact the sand
hecks:
1 - correct assembly and all the fasteners
2 - check the dimensions of the safety area compared to the play equipment

LOGBOOK
Type indication Adventure Play
Article number PSTE000.145
Product Name Springer beam
Maximum fall height 0,6 m
Construction year 2023
Certificate 032684
Inspection body TUV Nederland QA BV
Ekkersrijt 4401
5692 DL Son
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
BORG RVS M10DOPMOER 020010011BSR
4
1
M10 x 35 - RVS A2-70
Slotbout
035010026BSR42
M10 - VZ 8.8Bor moer 010010010BSV33
M10 X 80HOUTDRAADBOUT 080010022BSV44
M10x35SLOTBOUT 035010026BSV3
5
M10 VZSLUITRING 002010030BSV
7
6
Veerelement
Voetsteun 116PSTKST27
M10 zwart
Afdekdop zeskantbout
021010ZKDKST48
"stier"Veerplaat met voetsteun
905047PSTOME19
Schotel en U-bouten
Veer 40 cm, Ø 20 cm 905200
VER
SMD
1
10
Veerwippen
Grondanker
372149
MNP
SME
111
© Copyright BOERplay 10-8-2021 Revision: MOD PST 006 131
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
5
2
7
1
10
8
11
3
6
9
4

B
BB
Be
ee
en
nn
na
aa
am
mm
mi
ii
in
nn
ng
gg
g
Title
O
OO
Op
pp
pm
mm
me
ee
er
rr
rk
kk
ki
ii
in
nn
ng
gg
g
Comment
D
DD
Da
aa
at
tt
tu
uu
um
mm
m
Date
T
TT
Te
ee
ek
kk
ke
ee
en
nn
ni
ii
in
nn
ng
gg
g
Drawing
MOD PST 006 031
Veerbalk
Adventure Play
19-12-2011
BOER
S
SS
SP
PP
PE
EE
EE
EE
EL
LL
LT
TT
TO
OO
OE
EE
ES
SS
ST
TT
TE
EE
EL
LL
LL
LL
LE
EE
EN
NN
N
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
Lengte =3000Paal 18-20 030200PSTOHO
11
1
Beide uiteinden
afronden R>3 mm
Powered by TCPDF (www.tcpdf.org)