BOERPLAY Trio H1.30-1.10-0.90 User manual

Tumble bars Trio H1.30-1.10-0.90
PSTE000.087
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 087
Duikelrek
Trio L-M-H
19-9-2019
Afmetingen Dimensions
1,40 m
1,30 m
1,10 m
0,90 m
556
Staanders afvlakken zodat kopplaat duikelstang geheel tegen
staander komt. Uitstekende delen < 8 mm. (6x)
2,92 m
1,00 m
1,20 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 087
Duikelrek
Trio L-M-H
19-9-2019
Obstakelvrije zone Obstacle free zone
Obstakelvrij WAS
Obstacle free WAS
Opvangzone
Impact area
Obstakelvrij EN-1176
Obstacle free EN-1176
5,88 m
3,51 m
2,08 m 0,82 m 0,95 m
3,03 m 0,48 m
R1,50m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 087
Duikelrek
Trio L-M-H
19-9-2019
Bodemplan Groundplan
0,62 m
rondmarkering
Ground le el marker
5,88 m
R1,50m
R1,50m
0,58 m 0,92 m 0,83 m 0,96 m 0,57 m
1,52 m
3,51 m
0,01 m
0,00 m
0,00 m
0,00 m
0,15 m
0,38 m
2,26 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 087
Duikelrek
Trio L-M-H
19-9-2019
Modules Modules
OPMERKINGBENAMING
RBEH.
NR.PROJ.
TYPE
NPOS
Rek H=900Duikel
B
008007PSTMOD11
Rek H=1100Duikel
A
009007PSTMOD
1
2
Rek H=1300Duikel
A
012007PSTMOD
1
3
Paal H=1300Duikel
013007PSTMOD1
4
4
1
2
3
Typeplaatje
Identification plate
B

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 000 087
Duikelrek
Trio L-M-H
19-9-2019
Montage Mounting
Geleverde modules:
Zie tabel
Montageinstructie:
De hoofdmaten geven de maten van de staanders en vloeren aan
De detailtekeningen geven specifiek de maten van de verbindingen aan
De modules met buizen zijn op de tekeningen bemaat op bovenkant kopplaat
Overige modules zijn bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 Graaf de gaten volgens het bodemplan
2 Plaats 2 en 3
3 Verbind 2 en 3
4 Plaats 1
5 Verbind 1 en 2
6 Plaats 4
7 Verbind 4 en 3
8 Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
9 Dicht de gaten en verdicht het zand
Controles:
1 Correcte opbouw en alle bevestigingsmiddelen
2 Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
The main dimensions indicate the dimensions of the posts and floors
The detailed dimensions show the specific dimensions of the connections
The modules which contain tubes are dimensioned at the top of the flanges
Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 Dig the holes according to the ground plan
2 Place 2 and 3
3 Connect 2 and 3
4 Place 1
5 Connect 1 and 2
6 Place 4
7 Connect 4 and 3
8 Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
9 Close the holes and compact the sand
Checks:
1 Correct assembly and all the fasteners
2 Check the dimensions of the safety area with regard to the play equipment
4
3
2
1

LOGBOOK
Type indication Adventure Play
Article number PSTE000.087
Product Name Tumble bars Trio H1.30-1.10-0.90
Maximum fall height 1,3 m
Construction year 2023
Certificate 032370
Inspection body TUV Nederland QA BV
Ekkersrijt 4401
5692 DL Son
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 007 008 B
Duikel
Rek H=900
9-4-2019
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
5 x 70 - RVS A2-70
Schroef Assy
070005002BSR21
5 x 50 - RVS A2-70
Schroef Assy
050005002BSR22
RVS FA ETKRAALRING 015005036BSR23
Lengte =1600Paal 14-16 016160PSTOHO
14
Lengte = 500Standaard plank 120x20 050211PSTOHO
15
Adventure PlayDuikelbuis
A
320076PSTSME16
6
4
1
5
2 3
0,00 m
1,51 m
1,62 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 007 009 A
Duikel
Rek H=1100
18-4-2019
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
5 x 70 - RVS A2-70
Schroef Assy
070005002BSR21
5 x 50 - RVS A2-70
Schroef Assy
050005002BSR22
5 - RVS A2-70
Facet ring
015005036BSR23
Lengte =1800Paal 14-16 018160PSTOHO
14
Lengte = 500Standaard plank 120x20 050211PSTOHO
15
Adventure PlayDuikelbuis
A
320076PSTS E16
0,00 m
1,72 m
1,82 m
23
6
4
5
1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 007 012 A
Duikel
Rek H=1300
27-6-2019
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#
Nr.
5 x 70 - RVS A2-70
Schroef Assy
070005002BSR21
5 x 50 - RVS A2-70
Schroef Assy
050005002BSR22
RVS ACETKRAALRING 015005036BSR23
Lengte =2000Paal 14-16 020160PSTOHO
14
Lengte = 500Standaard plank 120x20 050211PSTOHO
15
Adventure PlayDuikelbuis
A
320076PSTSME16
4
6
2
3
0,00 m
1,92 m
2,02 m
1
5

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 007 013
Duikel
Paal H=1300
27-6-2019
Samenstelling module Assembly module
OpmerkingBenamingRev.Bew.Volgnr.Progr.Type
#
Nr.
5 x 70 - RVS A2-70
Schroef Ass
070005002BSR2
1
Lengte =2000Paal 10-12 020120PSTOHO
1
2
Lengte = 500
Standaard plank 120x20
050211PSTOHO13
2
3
1
Powered by TCPDF (www.tcpdf.org)