BOERPLAY Detached Slide with handles H1.5 User manual

Detached Slide with handles H1.5
BBPE020.3RR
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3RR B
Vrijstaande glijbaan 1,45 m
Boer Basic play
20-2-2017
BOER
SPEELTOESTELLEN
Hoofdafmetingen Main dimensions
0,00 m
1,45 m
2,16 m
0,00m 2,20m 2,36m 3,12m
0,00 m
0,05 m
0,85 m
0,90 m
66°
Openingen altijd > 25 mm
Openings always > 25 mm
<0,35m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3RR B
Vrijstaande glijbaan 1,45 m
Boer Basic play
20-2-2017
BOER
SPEELTOESTELLEN
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
6,17m
5,66m
R1,50m
3,89 m
R1,00m
R1,50m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3RR B
Vrijstaande glijbaan 1,45 m
Boer Basic play
20-2-2017
BOER
SPEELTOESTELLEN
Bodemplan Groundplan
Grondmarkering
Ground level marker
0,61 m
0,52 m
4,56 m
0,80m
1,55m1,54m
0,25 m
0,75m
0,38 m
0,10m
1,61 m
2,83 m
0,40m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3RR B
Vrijstaande glijbaan 1,45 m
Boer Basic play
20-2-2017
BOER
SPEELTOESTELLEN
Modules Modules
Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#Nr
Basic PlayGlijbaan 145 cm
R
14
BBP
MOD
11
Boer Basic playLadder 1,45m glijbaan
BR
5 9
BBP
MOD12
Geleverde modules:
Zie tabel
Montageinstructie:
- De hoofdmaten geven de maten van de staanders en vloeren aan
- De detailtekeningen geven specifiek de maten van de verbindingen aan
- De modules met buizen zi n op de tekeningen bemaat op bovenkant kopplaat
- Overige modules zi n bemaat op de bovenkant (klimwanden, paalkappen, etc.)
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - Plaats 1 onder de uiste hoek en met de uiste hoogte
3 - Plaats 2, verbind deze aan 1
4 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
5 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - De hoek van de trap
3 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied modules:
See table
Assembly instruction:
- The main dimensions indicate the dimensions of the posts and floors
- The detailed dimensions show the specific dimensions of the connections
- The modules which contain tubes are dimensioned at the top of the flanges
- Other modules are dimensioned at the top (climbing walls, caps for the posts, etc.)
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - Place 1 with the right angle and right height
3 - Place 2, attach it to 1
4 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - The angle of inclination of the ladder
3 - Check the dimensions of the safety area with regard to the play equipment
2
1
Typeplaatje
Identification plate
B

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE BBP 020 3RR B
Vrijstaande glijbaan 1,45 m
Boer Basic play
20-2-2017
BOER
SPEELTOESTELLEN
Afmetingen Dimensions
0,00 m
0,25 m
0,53 m
0,81 m
1,09 m
1,46 m
2,16 m
0,00 m
0,54 m
1,84 m
2,16 m

LOGBOOK
Type indication Basic Play
Article number BBPE020.3RR
Product Name Detached Slide with handles H1.5
Maximum fall height 1,5 m
Construction year 2023
Certificate 137792
Inspection body Keurmerkinstituut
Groeneweg 2e, Zoetermeer
2718AA Zoetermeer
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

Opmerking
BenamingRev.Bew.
Volgnr
Progr.Type#
Nr
BORG RVS M10DOPMOER 020010011BSR61
M10 x 40 - RVS A2-70Slotbout 040010026BSR62
M10 x 30 x 2,5CARROSSERIERING 030010035BSR63
145 m
Glijbaan
A
320664
VRB
SME1
4
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 146 R
Glijbaan 145 m
Basi Play
20-2-2017
BOER
SPEELTOESTELLEN
Samenstelling module Assembly module
2
3
1
4
Grondmarkering
Ground level marker
0,60 m
Let op: toestel bij voorkeur niet met
de glijbaan op het zuiden plaatsen.
Attention: it is advisable not to oriënt
pla ground equipment with the slide
facing south
1,45 m
0,29 m

A ( 1 : 10 )
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD BBP 569 R C
Ladder 1,45m glijbaan
Boer Basic play
5-2-2019
Samenstelling module Assembly module
OpmerkingBenamingRev.Bew.VolgnrProgr.Type
#
Nr
6.4 X 19.5 - H ls ALU, trekpen staalBlindklinknagel bolkop 056005014BSA16
1
4,8 x 30 - RVS A2-70Klinknagel bolkop 053005014BSR82
4,8 x 18 - RVS A2-70
Klinknagel bolkop
052005014BSR263
M10 - VZ 8.8
Borgdopmoer
020010011BSV44
M10x80
Slotbo t
080010026BSV45
M10 VZSLUITRING 002010030BSV46
Rond 6Lamellenstop 006013
LAM
KST2
7
Klemblok
090119
BBP
OPE28
L=2800 mm
Koker vierk. 100 x 2
320052208OME29
Al mini mPaalkap 100x100
B524100KAPOME210
100 x 100
Voetplaat
CVZP903VRBOME211
Boer Basic playHandgreep glijbaan
B
061136
BBP
OPE212
Basic PlayStartplatform glijbaan RVS
061092
BBP
OPE113
Boer Basics
Railing 003
BBP
SME
114
Basic PlayHandgreep
A
005
BBP
SME2
15
Basic PlayTraptrede
A
011
BBP
SME
4
16
A
66°
331
Grondmarkering
Ground level marker
9
10
7
15
3
12
2
16
1
11 3
13
5
6
4
8
430
0
503
765
777
1081
1385
1689
2077
2800
2817
46
25
Powered by TCPDF (www.tcpdf.org)