Terra Bound Solutions Kennel Club Playground User manual

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 1
Kennel Club Playground Installation Guideline
This space intentionally left blank.
Recommended Crew:
Minimum 1-2 People
Tools Required for Assembly:
T-30 TORX Bit
3/16” x 6” Drill Bit
Post Hole Digger / Shovel / Auger
Tape Measure
Level
High Speed 3/8” electric drill w/ clutch
Installation Time:
6 to 8 hours
Concrete Required:
1.8 cu ft. per post
Note: Concrete must have a minimum rating of 2,500 psi and must be mixed per
manufacturers recommendation.
20020 Hickory Twig Way ●Spring,Texas 77388
Phone: [phone] ●Fax: [phone]
Email: [email protected]
Web: www.terraboundsolutions.com

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 2
Kennel Club Playground Installation Guideline
Standard Hardware
5/16” x 5”
RSS Stainless
5/16” x 4”
RSS Stainless
5/16” x 3-1/8”
RSS Stainless
5/16” x 2-1/2”
RSS Stainless
1/4” x 2-1/2”
RSS Stainless
#10 x 2-1/2”
R4 Stainless
NOT TO SCALE!

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 3
Kennel Club Playground Installation Guideline
Check off all items received, against the packing list. Notify your local sales representative
immediately of any items that are missing or that may be damaged.
PLAYTOPIA, INC. IS NOT RESPONSIBLE
FOR ITEMS DISCOVERED MISSING
AFTER 72 HOURS FROM TIME OF
DELIVERY.
This space intentionally left blank.
Pre-Installation Check
PRE-DRILLING IS REQUIRED. ALL LOCATIONS WHERE
HARDWARE IS TO BE FASTENED REQUIRES PRE-
DRILLING TO ENSURE PROPER INSTALLATION AND
STRUCTURAL INTEGRITY. WE ARE NOT RESPONSIBLE
FOR INSTALLATION OR STRUCTURAL ISSUES THAT
ARISE FROM NOT PRE-DRILLING ATTACHMENTS.

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 4
Kennel Club Playground Installation Guideline
Kennel Club Components
Barrier Panel (x4)
Dog Ramp (x2)
Square Deck (x2)
Dog House Crawl (x4)
Dog Leap Bar (x2)
Dog Crawl (x1)
Dog A-Frame Roof (x1)
6’ Posts (x4)
10’ Posts (x4)

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 5
Kennel Club Playground Installation Guideline
When beginning the Kennel Club assembly, use the footer reference below to mark where
your post holes will be. The footer holes should be 12” in diameter by 18” deep. It is highly
recommended the concrete not be set until the completion of the Kennel Club assembly.
Kennel Club Post Footers

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 6
Kennel Club Playground Installation Guideline
Once your posts are in dry fitted and placed in the footer holes, begin to install the Kennel
Club deck platforms as shown below. The deck heights should be installed so that the tops of
the deck surface should be 40” from the ground surface.
Kennel Club Assembly
40” High

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 7
Kennel Club Playground Installation Guideline
Supporting the deck from underneath, fasten the platform using (8) 5/16”x3-1/8” RSS screws
(2 per corner) through the 2x3 deck frame and into the 4x4 post. Repeat the previous steps on
the remaining deck platform.
5/16” x 3-1/8” RSS Screw
Kennel Club Assembly (Contd.)

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 8
Kennel Club Playground Installation Guideline
With the deck platforms in place proceed to fasten the Dog House Crawl panels to the 4x4
posts as shown below. The panels are placed behind the 4x4 posts so that the outside edges of
the panels are flush with the outside edges of the 4x4 posts (A). The tops of the panels rest
directly up against the underside of the deck platform frame (B).
Kennel Club Assembly (Contd.)
B
A

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page 9
Kennel Club Playground Installation Guideline
With the panels in place fasten (6) 2-1/2” RSS Screws (3 per side) through the Dog House Crawl
panel and into the 4x4 posts. Repeat the previous steps on the remaining 3 Dog House Crawl
Panels until all are fastened in place.
5/16” x 2-1/2” RSS Screw
Kennel Club Assembly (Contd.)

REVISED DATE: 5/5/2016 KENNEL CLUB PLAYGROUND INSTALLATION GUIDELINE
Page10
Kennel Club Playground Installation Guideline
Proceed to place the Dog Barrier panels in the locations as shown below. The bottoms of the
barriers should be placed 1-1/2” to 2” above the surface of the deck platform. The outside
edges of the panels (C) should align flush with the outside of the 4x4 posts. Once in place
fasten (4) 5/16” x 2-1/2” RSS Screws (2 per side) through the barrier panel and into the post.
5/16” x 2-1/2” RSS Screw
Kennel Club Assembly (Contd.)
C