BONTEC GWM01 User manual

BONTEC
Monitor
Wall
Mount
Instruction
Manual
Model:
GWMO01

IMPORTANT SAFETY INFORMATION
e Please carefully read all instructions before attempting installation.
CAUTION: Avoid potential personal injuries and property damage!
e This product is designed for use in wood stud, solid concrete, concrete block
and
brick walls. — DO NOT install into drywall alone.
e Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
‘» This product contains a high pressure gas spring, fire and percussion prohibit-
ed. Also it is strictly prohibited to dismantle without professionals. Please return
to the manufacturer or hand over to professional agencies if the product is
abandoned.
e The wall must be capable of supporting three times the weight of the total load
(the mount, the monitor and all accessories weight).
Check the VESA Pattern of Your Monitor before the Installation
/
75 mm = 3in
100 mm = 4 in
200 mm = 7 7/8 in
Minimum VESA pattern: 75mm/3 in.(W)x75mm/3 in.(H)
[ if your Monitor VESA is greater than 200x200 mm/6x8 in. or less than 1
VESA 75x75mm/3x3in., this mount is NOT compatible.
01
Verify Your Wall Construction ‘
®/
§L
If
t
th
A\
CAUTION
:
you
are
not
sure
the
;
wall
construction,
'DO
NQT
please
contact
our
install
into
customer
service
at
drywall
alone
Wood
Studs
Solid
Concrete
[email protected].
(with
Drywall)
or
Concrete
Block
Tools
Needed
(Not
Included)
'
’
g / 7 &
Tape Measure
Stud
Finder
Pencil
Drill
Awl
/
/
%
/
ee
D)
el
5/32in.(4mm)
3/8
in.(10mm)
3/8in.(10mm)
Phillips
Lovel
Wood
Drill
Concrete
Drill
Socket
Wrench
Screwdriver
Supplied Parts and Hardware
AWarning:
This
product
contains
small
items
that
could
be
a
choking
hazard
if
swallowed.
*
Before
starting
assembly,
verify
all
parts
are
included
and
undamaged.
Do
not
use
damaged
or
defective
parts.
If
you
require
replacement
parts,
contact
our
customer
service
at
[email protected].
*
Please
note:
Not
all
hardware
included
in
this
package
will
be
used.
Supplied Parts and Hardware for Step 1
Faceplate
Extender
Bracket
M5
Nut
M5x12
Bolt
[02]
X1
[03]
x2
[04]
x
2
M-G
x8
M-H
x8
02

Supplied Parts and Hardware for Step 2
& Spacers [If needed] Washer
Note: The spacers are shown in
g_:_a\_g_c_:prdance with the actual size
Washer Spacer Spacer
D6 L13mm L5mm
M-D x4 M-E x4 M-F x4
Monitor Bolts [Only one bolt size fits your monitor]
Note: The bolts are shown in accordance with the actual size
M4
M6 x 16mm
M-C x4
Assembly/Wall Plate
[01] x1
Lag Screw
ST6.3x55mm
W-A x3
Washer
A\ W-B x3
Wall Anchor
o
@ =g M1 0x45mm
W-C x3
Supplied Parts and Hardware for Step 4 and Step 5
Large Allen Key
Bolt 15/64in.(6mm)
[ x1 T x1
Choose the Combination that Applies to Your VESA Hole
Pattern
200mm
(7.87 in.)
200mm ——
(7.87 in.)
200mm 100mm
(‘urgg)uwg,
(urye'e)wwioo
)
For VESA hole pattern:
2.95 inx2.95 in.(75x75mm)
3.94 in.x8.94 in.(100x100mm)
For VESA hole pattern:
7.87 in:x8.94 in.(200x100mm)
For VESA hole pattern:
7.87 inx7.87 in.(200x200mm)
04

Secure the Faceplate [02] or Faceplate [02] with
Extender Brackets [03 and 04] to Monitor -
Step 2
Only one bolt size fits your monitor.
M4
O
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination.
We recommend thread engagement by at least 5 turns.
—Too short will not hold the monitor.
—Too long will damage the monitor.
Too Short Too Long Correct
©)
L
) = p L
o—[NE
! (If Needed)
&
05
Option B (For Round Back Monitor)
iy (If Needed)
. O—EEER
Option C (For Monitor with A “Bump”)
Spacers may be necessary for 2 holes ONLY.
O—1V/=b)
premmeeees
(If
Néeded)
!
g
T
!
a
O
b (1f Needed)
R
-
N
-
'
' ; If Needed
ES
| : R\:
| @ (if Needed)
L L :
Option D
For cable interference or inset holes, use
spacers [M-E] and [M-F] to create extra
space between the monitor and faceplate
M-E/M-F
(If Needed)
i
|
= M-B/M-C
1
1
1
!
1
1
i
_.T..Lm
% ER
JIE| | _li0f Needed)
X
06

Step
3
Attach
the
Arm
Assembly/Wall
Plate
[01]
to
Wall
For
wood
stud
installation,
follow
STEP
3A
For
concrete
installation,
follow
STEP
3B
Step 3A 'Wood Stud Option
A\ WARNING:
@®Avoid
potential
personal
injury
or
property
damage!
DO
NOT
over-tighten
the
lag
screws
[W-A]
and
washers
[W-B].
Tighten
the
lag
screws
[W-A]
only
until
the
washers
[W-B]
are
pulled
firmly
against
the
arm
assembly/wall
plate
[01].
@®DO
NOT
USE
ANCHOR
[w-C]
FOR
THIS
STEP
@Ensure
the
arm
assembly/wall
plate
[01]
is
securely
fastened
to
the
wall
before
continuing
to
the
next
step.
®
Any
material
covering
the
wall
must
not
exceed
5/8
in.
(16
mm)
@®
Nominal
wood
stud
size:
common
2
x
4
in.
(51
x
102
mm)
minimum
1%
x
3V
in.
(38
x
89
mm)
@ Stud center must be verified
Use a stud finder(not included)
to locate wood studs or use an
awl (not included) to verify the
edges. Mark the edge and
center locations.
Awl
(Not Included)
Position the arm assembly/wall plate
[01] at your desired height and line
up the holes with your stud center
line. Level the arm assembly/wall
plate [01] and mark the holes.
e 2 You may need
assistance with this step.
\s
\ =
7
07
Drill 3 pilot holes using a 5/32 in.(4 mm)
diameter drill bit. Make sure the depth is
not less than 2 11/64 in.(55mm).
2 11/64 in.(55mm)
85/32 in.(4mm)
Install the arm assembly/wall plate
[01] using lag screws [W-A] and
washers [W-B]. Tighten the lag
screws [W-A] only until the washers
[w-B] are pulled firmly against the
wall plate.
2 You may need
assistance with this step.
3/8 in.(10 mm)
Socket Wrench
(Not Included)
Step
3B
Solid
Concrete
or
Concrete
Block
Option
A\
WARNING:
@
Avoid
potential
personal
injury
or
property
damage!
DO
NOT
over—tighten
the
lag
screws
[W-A].
Tighten
the
lag
screws
[W-A]
only
until
the
washers
[W-B]
are
pulled
firmly
against the wall
plate.
@®Ensure
the
arm
assembly/wall
plate
[01]
is
securely
fastened
to
the
wall
before
continuing
to
the
next
step.
Anchor
@®
Any
material
covering
the
wall
must
not
exceed
5/8
in.
(16
mm)
@®
Mount
the
wall
plate
directly
onto
the
concrete
surface
@
Minimum
solid
concrete
thickness:
203
mm
(8
in.)
®
Minimum
concrete
block
size:
203
x
203
x
406
mm
(8
x
8
x
16
in.)
@
Never
drill
into
the
mortar
between
blocks
08

You may need
assistance with this step.
Position arm assembly—
/wall plate [01] at your
desired height, level arm
assembly/wall plate [01]
fiF and mark the pilot hole
locations.
Drill 3 pilot holes using a 3/8
in.(10mm) diameter drill bit. Make
sure the depth is not less than 2
23/64 in.(60mm). Never drill into the
mortar between blocks.
%
2
23/64
in.(6Qmm)
23/8
in.(10mm)
Use the hammer to knock anchors
[w-c] into the wall. Be sure the
anchors [W-C] are seated flush
with the concrete surface.
(A
D vou may need assis—
tance with this step.
Install arm assembly/wall plate [01]
using lag screws [W-A], washers [W-B]
and anchors [W-C]. Tighten the lag
screws [W-A] only until the washers
[w-B] are pulled firmly against the wall
plate. DO NOT over-tighten the lag
screws [W-A].
3/8 in.(10 mm)
Socket Wrench
(Not Included)
Step 4. Hang the Monitor to the Mount
2 You may need
assistance with this step.
Be sure to keep the arm in horizontal
position during adjustment. Or else, it
would be difficult to adjust the mount or
fl
damage
the
mount.
1. If
the monitor
can
stay at
the desired
height by itself, no adjustment needed.
2. If the monitor rises up, press the arm to
keep it in horizontal position and then use
the Allen Key [T2] to turn the bolt clock-
wise(“~" direction) to reduce tension of the
arm only until the monitor can stay at the
desired height by itself.
3. If the monitor falls down, lift the arm to
keep it in horizontal position and then use
the Allen Key [T2] to turn the bolt count—
er—clockwise (“+” direction) to increase
tension of the arm only until the monitor
can stay at the desired height by itself.
gel Allen Key)
T
Y,
A\
T. N
(Small Allen Key) }
1. Slightly loosen the pre—assembled bolt [S].
2. Adjust the monitor to your desired tilt angle.
3. re—tighten the bolt [S] to secure the monitor in place.
10

Step
6.
Route
the
Cables
along
the
Arm
Swivel
Swivel
11