Bosaly M2100DT-UL User manual

BOSALY
IM2100DT-UL
ICE MAKER
Chuzhou Donlim Electrical Appliances CO., Ltd
No.1777 Yangzi East Road , Chuzhou City , Anhui Province
BOSALY

IM2100DT-UL
IMPORTANT
SAFEGUARDS
To reduce the risk of fire, explosion, electric shock, or
injury when using your ice maker, follow these important
safety instructions:
1. Before using check that the voltage power corre-
sponds to the one shown on the appliance nameplate.
2. Do not remove any safety, warning, or product
information labels from your ice maker.
3. Plug the ice maker into an exclusive grounded power
outlet. No other appliance should be plugged into the
same outlet. Be sure that the plug is fully inserted into the
receptacle.
4. This appliance must be grounded. It is equipped with
a power cord having a grounding plug. The plug must be
plugged into an outlet that is properly installed and
grounded.
5. Avoid the use of an extension cord because it may
overheat and cause a risk of fire. However, if it is neces-
sary to use an extension cord:
1)Use only extension cord with grounding plug.
2)The marked rating of an extension cord must be equal
to or greater than the rating of this appliance.
3)It should be positioned such that it does not drape over
the counter or tabletop where it can be pulled on by
children intentionally.
6. Do not operate any appliance with a damage cord or
plug or after the appliance malfunction or has been
damaged in any manner. Return the appliance to the
nearest authorized service facility for examination, repair
or adjustment.
7. If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
8. Do not let cord hang over edge of table or counter.
9. Do not place on or near a hot gas or electric burner, or
in a heated oven.
10. Place power cord in such a way it cannot be pulled on
by children or cause a tripping hazard.
11. Place power cord in such a way that it is not in
contact with hot surfaces.
12. The use of attachment not recommended or sold by
manufacturer may cause fire, electric shock or injury.
13. Do not touch the evaporator when using the ice
maker or making ice to avoid being suffer from frostbite.
14. Do not immerse any part of the product in water.
15. To disconnect, turn any control to “OFF”, then remove
plug from wall outlet.
16. Do not plug or unplug product with wet hands.
17. Unplug the product before cleaning,maintaining and
when not in use.
18. Do not use with water that is microbiologically unsafe
or of unknown quality.
19. Do not clean your ice maker with any flammable
fluids. The fumes may create a fire hazard or explosion.
20. Do not overturn the ice maker. If the ice maker is
overturned accidentally, make it stand steadily for 2 hours
before power it on again.
21. If the ice maker is brought in from outside in winter-
time, do not use for a few hours, allowing the unit to
warm up to the room temperature before operating.
22. Never put flammable, explosive and corrosive articles

into the ice maker.
23. Never use the ice maker when there is flammable gas
leakage.
24. Never store or use gas and other flammable articles
near the ice maker to avoid any fire.
25. Unplug the ice maker before moving it to avoid
damaging the refrigerating system.
26. Do not attempt to disassemble, repair, modify, or
replace any part of your product.
27. This appliance is not intended for used by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliances by a person responsible
for their safety.
28. Children should be supervised to ensure that they do
not play with the appliance.
29. Close supervision is necessary when any appliance is
used by or near children.
30. Do not leave the appliance unattended while in use.
31. Do not use outdoors.
32. Do not use the appliance for other than intended use.
33. Please abandon the ice maker according to local
regulators as it uses flammable blowing gas and refriger-
ant.
34. Please according to local regulations regarding
disposal of the appliance for its flammable refrigerant and
blowing gas.
KNOW YOUR ICE MAKER
CONTROL PANEL

1. Unpack the appliance, then check and make sure that
all the accessories including ice basket and ice scoop
etc. are complete. Please contact with the client service
department if some accessories are missed.
2. Please follow the operation as below to install the
handle well in position.
1)Grasp both sides of the handle shown in arrows with
hands and pull them outwards (see Fig.1).
2)Make the handle align with the holes at the housing
and release the hands, then the handle is inserted into
the holes of housing (see Fig.2).
3)Pull and make the handle be upright, then pull both
sides of the handle outwards by following the operation
of Step 1). Check and make sure that the handle shall be
positioned well at the holes of housing.
4)Grasp the center of handle and lift it upwards (see
Fig.3), check and make sure that there shall be no
abnormal condition can be found.
3. Please ensure the ice maker is level and on a stable
table or platform to avoid malfunction.
4. The incline angle of the ice maker cabinet should not
exceed 45°during transportation or use. Do not turn the
ice maker upside down. Doing so could cause the
compressor or refrigerating system to operate incorrectly.
Please allow time for the fluids in the compressor to
settle after the ice maker is moved or transported. Before
using the ice maker for the first time, please wait for 2
hours after the unit has been leveled and positioned in
the proper place.
BEFORE THE FIRST USE
Key (with indicator) Function
ON/OFF Start or stop the appliance
ICE Standby mode: “ICE” indicator
blinks; Working condition: “ICE”
indicator lights solidly.
ICE FULL “ICE FULL” indicator lights up
when the ice basket is full.
ADD WATER “ADD WATER” indicator lights
up when the water reservoir is
lack of water.
S The indicator lights up when
select small ice.
L The indicator lights up when
select large ice.
CLEAN “CLEAN” indicator lights up
when the appliance needs to
be cleaned
SELECT Can select “S”, “L” or “CLEAN”
under standby mode, after
power on, can select “S” or “L”.
Fig.1
Fig.2
Fig.3

7. The ice-making cycle will last approximately 7-15
minutes, depending on the ambient temperature and
water temperature.
8. The ice-making cycle starts with water being pumped
into the ice tray situated below the evaporator. Over the
next 7-15 minutes ice forms on the evaporator. Once this
has completed, the ice tray will tilt backwards and the
remaining water in the ice tray is drained back into the
water reservoir. The ice cubes are then dropped from the
evaporator and pushed forward into the ice basket by the
ice shovel. The ice tray will automatically move back into
position under the evaporator and start the next cycle.
9. The “ICE FULL” indicator will light up when the ice
basket is full and then the ice maker will stop the
ice-making cycle automatically. Gently remove the ice
from the ice basket with the ice scoop. About 7.5
seconds later, the ice maker will restart its ice making
function automatically.
10. The “ADD WATER” indicator will light up when the
water reservoir is lack of water and the ice-making cycle
will stop automatically. At that time, remove the ice
basket and add water to the water reservoir, and then
press “ON/OFF” key again to restart the ice-making
cycle.The appliance will start working automatically after
about 20minutes if the operator forgets to restart the
appliance after refill.
11. When you have got your desired amount of ice, stop
the ice making cycle by pressing the “ON/OFF” key and
unplug the unit from the wall outlet.
12. Open the top lid and transfer the ice to a freezer.
13. Allow the ice maker to reach room temperature.
USING YOUR ICE MAKER
5. The appliance must be placed on a dry and level
surface with sufficient ventilation, far from heat sources
such as ovens, heaters and corrosive gases.Leave about
a 6-inch (15cm) clearance on all sides of the ice maker
for proper ventilation.
6. Do not fill the water reservoir with hot water. This may
damage the ice maker. It is best to fill the water reservoir
with water of room temperature or lower.
7. Do not use the appliance at a very cold environment
(lower than 5℃).
8. Clean the appliance by following the operation of
“CLEANING AND MAINTENANCE” before operate.
1. Ensure that the drain plug at the bottom of water
reservoir is closed well.
2. Plug the ice maker into the wall outlet, the “ICE”
indicator blinks.
NOTE: Please make the ice maker be rested for 30
minutes before plug if it has been moved.
3. Open the top lid and remove the ice basket.
4. Fill the water reservoir with drinking water.
NOTE: Do not fill above the MAX water level mark.
5. Replace the ice basket and close the top lid.
6. Press “ON/OFF” key, and the “ICE”indicator lights
solidly. At that time, press ”SELECT” key to select the ice
size. If need to clean the appliance, press “SELECT” key
to select “CLEAN” function under standby mode.

14.Suggest replacing the water every a week. Please
empty the water reservoir if the ice maker is not used for
a long time.
To keep your ice tasting fresh and your ice maker looking
great, we recommend cleaning your ice maker once per
week.
1. Stop the ice-making cycle by pressing the “ON/OFF”
key, unplug the ice maker from the wall outlet and allow it
to warm up to room temperature.
2. If residual water is found in the ice tray, gently push
the ice tray back so that all water drains into the water
reservoir.
3. Move the appliance forward to a place 60mm away
from the working table and open the drain plug to drain
out excess water (see Fig.4, Fig.5 and Fig.6).
4. Check and make sure the drain plug must be closed
well. Fill the water reservoir with clean water, press‘SE-
LECT’until the ‘CLEAN’ indicator flashes,then press the
“ON/OFF” key , the pump will start to pump water and
keep running for 6 minutes, and it will enter into standby
condition after running for 6 minutes, finally, open the
drain plug and empty the water.
5. Remove the ice basket.
6. Clean the ice maker interior with a soft cloth soaked
with warm water and vinegar, then rinse with clean water
and then drain all the water.
7. Replace the drain plug well in position. Wash the ice
8. Clean the exterior of the ice maker with a soft damp
cloth. Use a mild dishwashing soap, if necessary.
NOTE:
1)Do not use organic solvent, boiled water, detergent,
strong acid and strong alkali etc. for cleaning.
2)Do not clean the evaporator.
9. Please empty the water reservoir and dry it for storage
if the ice maker is not used for a long time.
CLEANING AND MAINTENANCE
Fig.4
Fig.5 Fig.6

Problem
“ADD WATER”
indicator turns on
Possible causes Solution
1.Low water level or
lack of water
2.The water screen
at the bottom of
water reservoir is
blocked. Pump
malfunction.
1.Stop making ice,
refill water and then
press “ON/OFF” key
to restart ice-making
cycle.
2.Do cleaning
Send it to the
authorized
department for repair.
“ICE FULL” indicator
lights up
1.Ice basket is full
and the infrared light
is blocked by the ice.
2. Infrared
light-emitting diode &
light-receiving diode
do not work
1. Remove the ice
from ice basket.
2a. Wipe up the
foreign objects on the
infrared light-emitting
diode & l
ight-receiving diode
and restart the ice
maker.
2b. Call Customer
Service if the infrared
light-emitting diode &
light-receiving diode
still can not work after
wiping up the foreign
objects on them and
restarting the ice
maker.
The ice collects
together.
Making ice takes too
much time.
Stop making ice and
restart the
ice-making cycle
after the ice melts.
The water in the
water reservoir is of
too low temperature.
Fill the water
reservoir with water
ranges between 8℃
and 25℃.
The ice-making cycle
seems normal but no
ice is produced.
The ambient
temperature or water
temperature is too
high.
Start the ice-making
cycle at a
environment with an
ambient temperature
less than 32°C and
fill the water reservoir
with some cold water.
Refrigerating system
leaks
Call customer service
Poor ice-making
result
1.Poor heat
dissipation.
2.The water
temperature is too
high.
The ambient
temperature is too
high.
1.Leave a 6-inch
clearance on all sides
of the ice maker for
proper ventilation.
2.Fill the water
reservoir with water
ranges between 8℃
and 28℃.
Operate the ice maker
at a environment with
an ambient
temperature between
10℃and 32℃.
Refrigerating system
blocks
Call customer service

TECHNICAL PARAMETERS
Model: IM2100DT-UL
Electrical Rating: AMPS 1.7A 120V AC 60Hz
Refrigerant: R600a/0.8oz
Design Pressure : High Side :290Psig
Low Side :138 Psig
Minimun Installation Clearance
Top 6.0 IN BACK 6.0 IN Sides 6.0 IN