Boss Audio Systems LPCB40 User manual
0523
Introduction
This camera is designed for use as a front view or rear-facing backup
camera, and mounted neatly behind your license plate. When installed
with any of our camera-capable head units, the camera view can be
automatically triggered when shifting into reverse or manually triggered by
selecting the camera button from the head unit home screen.
Package Contents
• 1x Camera with power and video sockets
• 1x Power cable with power plug
• 1x Video cable with two yellow RCA plugs
• User manual
Important
Please read and understand all instructions before you use your product.
Failure to follow the instructions could result in injury and/or damage that
could potentially void the warranty.
Important safety precautions
• Use of the camera must not replace other safe driving habits. Precise
control and looking around before backing up is necessary.
• Always remember that the area displayed by the camera is limited, and
certain obstacles may not be detected or not reliably detected.
Installation precautions
• WARNING: Always consult a professional installer.
• Improper wiring and mounting of the camera can cause damage, injury
or accident. Have installation performed by a professional only. Contact
our technical support for any installation questions.
• Disconnect the negative terminal of the vehicle battery prior to wiring.
• When making modications to your car due to the installation, make
sure the safety and structural integrity of the car is not impaired.
• Hide wires under car oor mat or through car headliner. Make sure
wires are not squeezed or damaged by sharp edges. Use rubber
bushings for penetrations.
1
Wiring
• Follow two steps described below to install this product as a front
camera or a rear camera.
• The rear camera view automatically turns on when reversing. Ensure
you connect the “Reverse Input” wire on your head unit to the vehicle’s
reverse light for reverse trigger. Front camera view is not accessible
when reversing.
• Both rear and front camera view can be selected via Home screen
options on your head unit.
1. Connect the video cables.
aConnect one yellow RCA plug of
the video cable to your head unit.
Front camera: to “Front Camera
Input” RCA socket.
Rear camera: to “Rear Camera
Input” RCA socket.
bConnect the other yellow RCA plug
of the video cable to the yellow
RCA socket on the camera.
2. Connect the power cables.
cConnect the red split wire of the
video cable to your head unit.
Front camera: to “Front Camera
Power Output” wire.
Rear camera: to “Rear Camera
Power Output” wire.
dConnect the other red split wire of
the video cable to the red wire of
the power cable.
eConnect the black (ground) wire of
the power cable to the car chassis.
fConnect the black plug of the power cable to the red socket on the
camera.
2
(+)(-)
a
b
c
d
e
f
Front or rear cam
power wire
Camera
2
Mounting
The camera is designed for mounting behind the license plate of your car
through the screw holes on the license plate. No drilling hole is required.
1. Remove the license plate lamp. Through the opening of the license
plate lamp, run the camera’s cable from the outside into the inside of
the car.
2. Remove the license plate screws. Align the camera frame with two top
screw holes on the license plate, and secure the camera frame with two
license plate screws. Make sure the camera is correctly oriented to
avoid reverse image.
Camera frame
License plate frame
3. Verify the camera angle is properly positioned. If needed, loosen the
screws and adjust the camera angle then re-tighten the screws.
Troubleshooting
Problem Solution
No image Ensure the camera’s power cable is securely plugged.
Ensure there is correct and secure wiring between the
camera and your head unit.
Ensure the reverse input wire on your head unit is
connected to the vehicle’s reverse light.
Ensure correct camera settings on your head unit.
Image blurry Check for water drops or dust on the camera lens.
Clean it with a damp, ber-free cloth.
Image shaking Ensure the camera is tightly mounted.
Image slanted Adjust the camera frame position.
3
Image Setting
• To remove the on-screen parking guidelines, cut open the white wire
loop which splits from the camera’s cable. Otherwise, keep the white
wire loop uncut.
• If the camera image appears reverse, cut open the blue wire loop
which splits from the camera’s cable. Otherwise, keep the blue wire
loop uncut.
• Make sure to unplug the power cable from the camera and plug it again
to enable the new setting (after cutting off the white or blue wire loop).
Specications
Power supply...................................12 VDC
Viewing angle ..................................170°
TV system........................................NTSC
Video output ....................................1.0 vp-p, 75 Ω
S/N ratio...........................................≤45 dB
Ingress protection rating..................IP67 (waterproof)
Operating conditions........................ -22 to +140°F (-30 to +60°C)
max. 95% RH
White balance..................................Auto
Illumination ......................................min. 0.1 lux
Automatic gain control (AGC)..........Auto
Resolution (TV lines) .......................480
Electronic shutter speed..................1/60 (NTSC)
Effective pixels.................................648 x 488
Dimensions (L x W x H)................... 7.756” x 0.88” x 0.88”
197 x 22 x 22 mm
Cable length .................................... 197”/5m (video cable); 39”/1m (power
cable); 20”/0.5m (camera’s cable)
Specications are subject to change without notice.
4
0523
Table of contents
