BRAVILOR BONAMAT Bolero 10 User manual

Operating instructions GB
HOT BEVERAGE BREWER

 
12
10
3
9
8
7
4
65
20
21
11
12
13
14
15
16
17
18
19
2.3
2.4 2.5
2.1
2.2












200
710
245
W=40 E=37
55
400
115
243

1
Instruction Manual English
1.1 Introduction
We are delighted that you have chosen
one of our quality products, the Bolero F.
These machines are specially designed
for making hot beverages such as coffee,
hot chocolate, etc.
In order to gain full and safe benefit from
this machine's facilities, we advise you to
read this manual carefully.
We recommend that you keep the double
page unfolded
while reading
this manual.
Contence Page
1.1 INTRODUCTION ............................................................... 1
1.2 MODELS AND TYPES ....................................................... 1
1.3 WARNINGS AND PRECAUTIONS ........................................ 2
1.3.1 Warnings.......................................................... 2
1.3.2 Precautions ...................................................... 2
1.4 A QUICK MACHINE GUIDE................................................. 3
1.4.1 Accessories...................................................... 3
1.5 INSTALLING THE MACHINE AND SETTING UP FOR
OPERATION .................................................................... 4
1.6 INSTALLING THE MACHINE AND SETTING UP FOR
OPERATION (CONTINUED)................................................ 5
1.6.1 Hot-water tap ................................................... 5
1.7 SETTINGS ...................................................................... 5
1.8 GENERAL PROGRAMMING PROCEDURE ............................ 6
1.8.1 In general..........................................................6
1.8.2 Activating the settings program ........................6
1.8.3 Closing the settings program............................6
1.9 STEP-BY-STEP PROGRAMMING.........................................7
1.9.1 Starting the rinsing program .............................7
1.9.2 Start descaling program ...................................7
1.10 STEP BY STEP PROGRAMMING (CONTINUED).....................8
1.10.1 Setting the quantity of beverage per cup..........8
1.10.2 Setting the quantity of beverage per semi
decanter............................................................8
1.10.3 Setting the quantity of beverage per full
decanter............................................................8
1.11 STEP BY STEP PROGRAMMING (CONTINUED).....................9
1.11.1 Setting the strength of beverage ......................9
1.11.2 Switching the mixer on or off when tapping
cups..................................................................9
1.11.3 Switching the mixer on or off when tapping
semi decanters .................................................9
1.11.4 Switching the mixer on or off when tapping
decanters..........................................................9
1.12 STEP BY STEP PROGRAMMING (CONTINUED)...................10
1.12.1 Setting the temperature off the hot water
buffer stock.....................................................10
1.12.2 Setting the hot water temperature ..................10
1.12.3 Setting descaling signal..................................10
1.13 USAGE 11
1.13.1 Hot-water tap..................................................11
1.13.2 Stopping the brewing process ........................11
1.14 MAINTENANCE ..............................................................12
1.14.1 Daily maintenance: .........................................12
1.14.2 Weekly maintenance: .....................................12
1.14.3 Cleaning the ingredient container:..................12
1.14.4 Removing and cleaning ventilator ..................12
1.15 DESCALING...................................................................13
1.16 MALFUNCTIONS ............................................................14
1.2 Models and types
This instruction manual applies to the
following machines:
Model: Blr010F-001 (with plastic
corkscrew).
Model: Blr011F-001 (with metal spiral).
See the type plate on the machine for
data relating to power, model and type
number, etc. We recommend that you
record this data in the drawing of the type
plate in the back of this instruction
manual.

2
1.3 Warnings and precautions
Please observe the following warnings
and precautions for safe use of the
Bolero F:
1.3.1 WARNINGS
∆Never submerge the machine in water.
∆Stay with the machine during
maintenance activities such as
descaling.
∆The machine must be connected to the
power and water supply in such a way
that it can be detached easily.
∆The manufacturer accepts no liability for
any damage resulting from installation,
use or maintenance that is not in
compliance with this manual.
∆It is very important not to use regular
silicon grease on the axle (4.8). It has to
be silicon grease for food purpose use
only.
∆Avoid touching moving parts when
opening the machine. This can be
dangerous!
1.3.2 PRECAUTIONS
•If the machine is not used for some
considerable time, it is recommended
that you disconnect the water- and
power supply.
•Normally some water will always remain
inside the machine, please note this
carefully before placing the machine in
a room where the temperature might
drop below 0° Celsius.
•If you are using a strong detergent or
descaling agent, it is highly recommen-
ded to wear safety goggles (facial
protection) and gloves.
•Avoid spilling descaling agent on the
outside of the machine, as this may
result in lasting damage to the housing.
Remove any accidentally spilled
descaling agent immediately, while
taking all necessary warnings and
safety precautions mentioned in this
manual.
•Wash you hands after using a strong
detergent or descaling agent.
•All repairs must be performed by the
Bravilor Bonamat dealer or a skilled and
authorised expert.
•Remove the plug from the mains socket
before opening the machine, e.g. for
maintenance or repairs.
•Always connect this machine to an
earthed wall socket.
•Always use approved materials and
parts for installing or repairing this
machine.
•This machine must be connected to the
water supply using a manually operated
tap and the water hose supplied.
•Always observe local rules and
standards when installing this machine.
•This machine can only be used in a
room where the temperature will not fall
below 2°C or rise above 30°C.
•If this machine is exposed to
temperatures below freezing point, the
remaining water inside will freeze. If this
is the case, do not switch the machine
on, unplug it and call your service
engineer.
•Do not place this machine on a surface
at a slope of more than 5°.

3
1.4 A quick machine guide
The double page presents the most
important parts of the machine. Keep this
double page unfolded &while reading
this instruction manual.
1. On/off switch of the machine
2. Container for ingredients with
dispensing mechanism
2.1 Lid of container for ingredients
2.2 Outlet (discharge opening)
2.3 Corkscrew (plastic) or
Spiral (metal)
2.4 Connection piece
2.5 Gear wheel
3. Program switch
4. Mixing basin
4.1 Mixing basin (upper)
4.1.1 Extraction aperture
4.2 Mixing basin (lower)
4.3 Hose
4.4 Mixing chamber
4.5 Outlet
4.6 Mixer
4.6.1 Point (on mixer)
4.7 Base plate
4.8 Axle
5. Drain hose
6. Hot-water cock
7. Hot-water syphon
8. Inlet for descaling agent
9. Top cover
10. Door
11. Display
12. Selection key
13. Start button (=setting key for
program)
14. Beverage outlet
15. Drip-tray
16. Drip-tray cover plate
17. Foldaway tableau for cups
18. Hot-water outlet
19. Hot-water tap
20. Lock with key
21. Opening for fixing driptray
22. Ventilator
22.1 Grate
22.2 Ventilator
1.4.1 ACCESSORIES
•Renegite
•Funnel
•Water connection hose
•Drip-tray with cover plate
•Keys
•Brush
•Operating instructions
•Sticker sheet
When the machine requires descaling,
the descaling symbol (see figure 1)
appears in the display (11).
Fi
g
. 1
Fi
g
. 2
Fi
g
. 3

4
1.5 Installing the machine and setting up for operation
1. Place the machine on the work
surface. Leave a minimum of 6 cm
clear on the right-hand side so that
the door (10) can be opened.
2. Place the sticker “hot water” in the
recess above the hot water tap (17).
3. Place the required sticker (coffee,
chocolate, etc.) in the recess above
the beverage outlet (14).
4. Make sure that the machine is stable
and horizontal.
5. Check whether an earthed wall
socket and water supply are close by.
6. Connect the machine to the water
supply (via a tap) with the supplied
connection hose.
7. Open the tap.
8. Insert the plug in the earthed wall
socket.
9. Place the drip-tray (15) in front of the
machine. Put the fixing cams into the
opening (21).
−It is possible to connect a drain
hose to the drip-tray. A small spout
is provided at the rear of the
drip-tray. Drill a hole in this and
slide the hose onto it.
10. Open the door (10) on the left-hand
side with the key (20).
11. Open the cover of the machine (9).
12. Remove the lid (2.1) from the
ingredient container. Fill the
ingredient container with the special
ingredients available for these
machines.
13. Replace the lid on the ingredient
container.
14. Switch on the machine. Set switch (1)
to the 'on' position, which shows a red
indicator side at the switch.
15. The version number of the machine
appears briefly in the display (11).
(Inform the engineer of this number in
case of repair or maintenance.) A cup
then appears in the display, see
figure 2.
−The machine will now fill with
water.
−The water will be heated.
16. Close the cover (9).
17. Push the door to close it.
18. Lock the door with the key (20).
19. A flashing thermometer will appear in
the top right-hand corner of the
display, see figure 3.
20. When the water is hot enough, the
thermometer will disappear from the
display.
21. Fold out the tableau for cups.
22. Place an empty coffee cup on the
tableau, under the beverage outlet
(14).
23. Push the start button (13).
24. The beverage is dispensed into the
cup. (The cup in the display flashes
while the beverage is dispensed.)
25. Discard the first two cups of
beverage.
26. Replace the cup under the outlet and
push the start button (13) again.
27. Check whether the quantity and taste
of the beverage are to your
satisfaction.
−Is the quantity unsatisfactory,
proceed to chapter 1.10.1 Setting
the quantity of beverage per cup.
−Is the taste unsatisfactory, proceed
to chapter 1.11.1 Setting the
strength of beverage.
−If the quantity and the taste are
satisfactory, proceed to check the
quantitiy for semi decanters.
28. Fold away the tableau for cups.
29. Place an empty decanter under the
beverage outlet (14) and push the
selection key (12) once to
select a semi decanter. (A semi filled
decanter appears in the display (11)).
30. Push the start button (13).
The beverage is dispensed into the
decanter.
31. Check whether the quantity is to your
satisfaction.
−Is the quantity unsatisfactory,
proceed to chapter 1.10.2 Setting
the quantity of beverage per semi
decanter.
−If the quantity is satisfactory,
proceed to check the quantitiy for
full decanters.

5
1.6 Installing the machine and setting up for operation (continued)
32. Place an empty decanter under the
beverage outlet (14) and push the
selection key (12) twice to
select a full decanter. (A fully filled
decanter appears in the display (11)).
33. Push the start button (13).
The beverage is dispensed into the
decanter.
34. Check whether the quantity is to your
satisfaction.
−Is the quantity unsatisfactory,
proceed to chapter 1.10.3 Setting
the quantity of beverage per full
decanter.
35. The beverage maker is ready for use
when the quantity of the full decanter
also is satisfactory.
1.6.1 HOT-WATER TAP
1. Place a cup under the hot-water
outlet (18).
2. Draw off a cup of hot water via the
hot-water tap (19) and discard this.
The hot-water system is now ready for
use.
1.7 Settings
The machine is equipped with a program
that allows you to set all the facilities of
the beverage maker. The program
comprises nine components in the
following sequence:
1. § 1.9.1 Starting the rinsing program.
2. § 1.9.2 Start descaling program.
3. § 1.10.1 Setting the quantity of
beverage per cup.
4. § 1.10.2 Setting the quantity of
beverage per semi decanter.
5. § 1.10.3 Setting the quantity of
beverage per full decanter.
6. § 1.11.1 Setting the strength of
beverage.
7. § 1.11.2 Switching the mixer on or off
when tapping cups.
8. § 1.11.3 Switching the mixer on or off
when tapping semi decanters.
9. § 1.11.4 Switching the mixer on or off
when tapping full decanters.
10. § 1.12.1 Setting the temperature off
the hot water buffer stock
11. § 1.12.2 Setting the hot water
temperature.
12. § 1.12.3 Setting descaling signal.

6
1.8 General programming procedure
1.8.1 IN GENERAL
Before you start programming, remember
which settings have to be changed.
Make a note of the settings you wish to
change. You can then enter all the
changes in one go, one after the other.
An explanation of the different setting
possibilities is given in § 1.10.1 trough
1.12.3.
1.8.2 ACTIVATING THE SETTINGS PROGRAM
1. Open the door with the key (20).
2. Switch on the machine. Set switch (1)
to the 'on' position, which shows a red
indicator side at the switch.
3. Press the programming button (3) on
the inside of the door.
4. In the display (11) on the outside of
the door appears the following
counters one after the other:
−The number of
brewed cups of
beverage;
−The number of
brewed semi
decanters of
beverage;
−The number of
brewed full
decanters of
beverage, see
figure 4.
5. Attention! These counters will be
repeated three times than the
program returns to normal mode. If
this happens just press again the
programming button (3).
6. Press selection key (12). The
cleaning program will appear in the
display, see figure 5.
7. Press selection key (12) again
to proceed to the next possible
program/setting.
In this manner you can use the
selection key to run through all
the settings in the program. The
display shows what can be set after
each step.
1.8.3 CLOSING THE SETTINGS PROGRAM
1. If you have finished setting up the
program, press the programming
button (3) on the inside of the door
again. The new settings will now be
saved.
2. Check whether the changed settings
from point 3 to 11 of § 1.7 are
according to your requirements, by
tapping of a cup or decanter. If not,
change the settings until they comply
with your wishes.
Fi
g
. 4

7
1.9 Step-by-step programming
1.9.1 STARTING THE RINSING PROGRAM
1. Select the rinsing program. Figure 5
now appears in the display.
2. Place a decanter under the beverage
outlet (14).
3. Press on the right-hand side of the
start button ß(13). The rinsing
program now flushes the machine
with hot water. This runs into the
decanter.
4. Discard this water.
5. Repeat steps 3 and 4 until the water
in the decanter is clear. Press the
programming key to return.
The machine is again ready for use.
1.9.2 START DESCALING PROGRAM
1. Open the door (10) and flip the cover
(9) up.
2. Remove the ingredient container (2)
and the drip-tray (15).
3. Press the programming key (3).
4. Select the descaling program with
selection key (12). Figure 6
appears in the display.
5. Press the right-hand side of the start
button ß(13).
−Cancelling the descaling
program, see point 25.
6. Pull out the drain hose (5).
7. Place the drain hose (5) over the
edge of a bucket that can hold at
least 7 litres.
CARE! Water that is leaving the hose
may be hot!
8. Remove the drain plug of the drain
hose (5) to allow the water out into
the drain or the bucket.
9. Replace the plug on the hose.
10. Gently remove the hose (4.3) from the
mixer chamber (4.2) and place it over
the edge of a bucket.
11. Dissolve 100 grams Renegite in
approx. 0,5 litre warm water.
12. Remove the plug from the descaling
inlet (8).
13. Use a funnel to pour the descaling
solution into the descaling inlet (8) and
close the inlet again with the plug.
14. Leave the Renegite solution for a few
minutes to take effect.
15. Press on the right-hand side of the
start button ß(13). The descaling
program now starts and will last for
approx. 15 minutes. The machine will
be rinsed with water.
16. Tap a few cups of water through the
hot-water tap to flush the hot-water
outlet.
17. Remove the drain plug of the drain
hose (5) to allow the water out into
the drain or the bucket.
18. Replace the plug on the hose.
19. Replace the ingredient container (2).
20. Replace the drain hose (5) in its
original position and close the lid and
the door.
21. Replace the drip-tray (15).
22. Press the programming key (3). The
machine will now fill with water and
the water will be heated.
23. The machine is again ready for use.
24. The descaling signal is now
automatically reset .
Fig. 5
Fig. 6
PRECAUTIONARY MEASURE **
•Stay with the machine throughout the
descaling process.
•Wear gloves and a facial protector
while descaling.