Breathablebaby Breathable mesh mini crib User manual

Breathable™ Mesh Mini Crib

Customer Care:

Email: [email protected]m

Style #:

Lot:

Date:

_______ ____

___________

BreathableBaby, LLC.

2481 Hedberg Drive

Minnetonka, MN 55305

Phone: 877-827-4442

This product is not intended for institutional or commercial use.

Read all instructions before assembly and use.

KEEP INSTRUCTIONS FOR FUTURE USE.

ADULT ASSEMBLY REQUIRED

Due to the presence of small parts during assembly,

keep out of reach of children until assembly is complete.

MM/YYYY

50118

PO #

Ages 0–24 months

(or 35" tall)

To register your product for important safety alerts and updates to your product please visit

BreathableBaby.com/Registration

Please do not return this item to the store before contacting us about missing parts or with any questions.

Care and Cleaning:

Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning.

Clean wood or mesh with mild soap on a soft rag. Wipe again with clean water and let dry thoroughly.

If you ever refinish this furniture, be sure to use only a non-toxic finish specified for children’s products.

As with all your fine furniture, blot up spills immediately.

If optional legs are not used, use pad underneath crib to prevent scratches to floor.

WARNING:

FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN SERIOUS

INJURY OR DEATH. DO NOT USE THIS PRODUCT IF YOU CANNOT EXACTLY FOLLOW THE

INSTRUCTIONS THAT COME WITH IT. THIS PRODUCT SHOULD BE FULLY ASSEMBLED PRIOR TO USE.

SUFFOCATION HAZARD-Infants have suffocated:

• In gaps between extra padding and side of the product.

• On soft bedding.

• Use ONLY mattress/pad provided by BreathableBaby, LLC

(which must be at least 37 1/2 inches long by 23 1/2 inches wide and not

more than 1 1/2 inches thick). Call BreathableBaby for replacement.

•NEVER add a pillow, comforter, or another mattress for padding.

• If a sheet is used with the pad, use only the one provided by

BreathableBaby, LLC. Call BreathableBaby for additional sheets.

• To reduce the risk of SIDS, pediatricians recommend healthy infants be

placed on their back to sleep, unless otherwise advised by your physician.

FALL HAZARD

• Discontinue use of the product when child is able to climb out or reaches the height of 35 in. (890 mm).

• When child is able to pull to standing position, remove bumper pads, large toys, and other objects that

could serve as steps for climbing out.

• The p/roduct, including side rails, must be fully erected prior to use.

• Child can become entrapped and die when improvised netting or covers are placed on top of a product.

NEVER add such items to confine child in product.

• Always use all required parts.

•NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn

mesh/fabric. Check instruction manual for a list of required parts. Check before assembly and periodically

during use. DO NOT substitute parts. Contact BreathableBaby, LLC. if replacement parts or instructions

are needed.

• Strings can cause strangulation! NEVER place items with a string around a child’s neck such as hood

strings or pacifier cords. NEVER suspend strings over product or attach strings to toys.

• Make sure latches are secure.

•NEVER place product near window where cords from blinds or drapes can strangle a child.

•NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that

purpose. They can cause suffocation.

•NEVER use a water mattress with this product.

• If refinishing, use a nontoxic finish specified for children’s products.

•NEVER place product near patio doors with cords where a child could reach the cord and be strangled, or

hang strings over the product or place items with a string around an infant’s neck or attach strings to toys.

•DO NOT place any cord or strap or similar item in or near this product that could become wrapped around

a child’s neck.

• Assure that platform is attached securely to support brackets with provided screws.

• Always provide the supervision necessary for the continued safety of your child. When used for playing,

never leave child unattended.

WARNING:

Assembly Instructions

Upper Level:

Mattress in top position.

(Move to bottom position

when infant begins to push

up on hands and knees,

can roll over or has reached

20 lbs., whichever comes first.

UPPER LEVEL

MATTRESS –

MINI CRIB

Lower Level:

Mattress in bottom position.

Discontinue use of the product

when child is able to climb out

or reaches the height of 35 in.

Page 1

LOWER LEVEL MATTRESS – MINI CRIB

Required Tools:

No drills necessary.

Do not use power

screwdriver.

DO NOT USE IF ANY PART IS BROKEN, TORN, OR MISSING.

CONTACT BREATHABLEBABY CONSUMER CARE IN THAT EVENT.

Back Mesh Rail

Front Mesh Rail

Right Solid End

Left Solid End

Legs

Allen Wrench supplied

For every bolt, be sure to

hand tighten snugly but

DO NOT over-tighten.

Page 2

Parts List 1 of 2

Bolts M6 x 20mm = 8 pcs

Bolts M6 x 30mm = 8 pcs

Bolts M6 x 65mm = 8 pcs

Allen Wrench = 1 pc

L-Bracket = 4 pcs

Flat Washer = 16 pcs

Lock Washer = 16 pcs

Parts List 2 of 2

Page 3

Mattress Pad (E x 1) Sheet (F x 1)

10 Flat Head Bolts M6 x 20mm = 4 pcs

Front Side Rail

Back Mesh Rail Right Solid End

Left Solid End

Attach (Part A) Back Mesh Rail and (Part B) Left Solid End

with 2 (Part 3) Bolts and (Part 7) lock washers. Attach (Part A)

Front Mesh Side Rail also with 2 (Part 3) Bolts and (Part 7) lock

washers. Attached (Part B) Right Solid End to both (Part As)

with 4 (Part 3) Bolts and (Parts 7) lock washers.

WARNING: For the mesh panels, make sure the side with

the support bars is installed facing out and on the outside of

the crib. The side with flat mesh only should be on the inside

facing child.

For the solid end panels, make sure the side with the indented

panel is facing out and the flat side facing in toward the child.

Page 4

Step 1

Option #1- For Upper Level Mattress Platform Position

For Upper Level Mattress Only: Attach the 4 (Part 5)

L-Brackets to the 4 holes on the inside of the mesh rails just

below the outside support bar on both insides of the crib

with (Part 1) Bolts. Make sure the L-Bracket has the flat side

facing upwards and level so the mattress platform can rest

on top. See "circles" on this image for approximate

placement of the 4 L-Brackets.

Install the 4 Flat Head Bolts (Part 10) into the empty holes

where the bottom platform will be positioned in the future

to prevent empty holes for safety.

------------------------------------------------------------

---

Page 5

Step 2A

For Upper Level Mattress Platform

WARNING: Move to Lower Level when

infant begins to push up on hands and

knees, can roll over or has reached 20 lbs.,

whichever comes first.

For Lower Level Mattress Only: Attach the 4 (Part 5)

L-Brackets to the 4 holes on the inside of the mesh rails near

the bottom on both insides of the crib with (Part 1) Bolts.

Make sure the L-Bracket has the flat side facing upwards and

level so the mattress platform can rest on top. See "circles" on

this image for approximate placement of the 4 L-Brackets.

Install the 4 Flat Head Bolts (Part 10) into the empty holes

where the platform would be positioned if it where in the

upper level to prevent empty holes for safety.

Step 2B (Only if assembly directly to Lower Level Mattress)

For Lower Level Mattress Platform Page 6

Option #2- For Lower Level Mattress Platform Position

WARNING: Discontinue use of this

product when child is able to climb out

or reaches the height of 35 in.

WARNING: DO NOT USE crib if the

Mattress Base is not firmly secured

to the L-Brackets at all 4 corners.

Page 7

Step 3 Attach Mattress Platform

Best for 2 people at this step. Turn crib on side and insert (Part C) Mattress Base through the opening in the top of the crib.

Hold the Mattress Base flat against the top of the L-Brackets installed in Step 2A or 2B. Use the 2 holes in platform to help

you handle. Then from the underside of the crib, attach (Part 1) Bolts through the bottom of the L-Bracket and into the

corresponding holes in each of the 4 corners of the Mattress Base.

Leg Attachment – Optional

Page 8

Helpful Hint:

Get a second person

to help flip crib over.

Place crib upside down. Attach 4x (Part D) Legs to holes on bottom of

both (Part B) Solid Ends. Attach each leg with 2 (Part 2) Bolts, 1 (Part 7)

Lock Washer, and 1 (Part 6) Flat Washer.

Turn crib upright. Be careful not to put too much pressure on legs

while turning over.

Place included mattress onto Mattress Base and install sheet

snugly onto mattress. Enjoy your Breathable™ Mesh Mini Crib.

Step 4 Leg Attachment (optional)

Warning: If optional legs are not used, store legs and all extra hardware somewhere safely out of reach of child.

Warning- Make sure legs are installed

slanted to the outside of the crib.

If optional legs are not used, use pad underneath crib to protect floor from damage.

Lowering Mattress Platform Instructions

Move mattress and mattress base to bottom crib position when infant begins to push up on hands

and knees, can roll over or has reached 20 lbs., whichever comes first.

WARNING: DO NOT USE crib if the Mattress Base is

not firmly secured to the L-Brackets at all 4 corners.

Turn crib on side and detach Mattress Base from L-Brackets by unscrewing bolts with allen wrench (M6). Set Mattress Base to the side temporarily. Remove the L-

Brackets from the bassinet level by unscrewing the remaining 4 bolts.

Remove the 4 Flat Head Bolts (Part 10) installed during Step 2A in the screw holes on the side rail for the lower platform level. Use the removed 4 bolts and re-

install into the empty screw holes higher on the side rails created when you just removed the upper platform to prevent empty holes for safety.

Re-attach the 4 (Part 5) L-Brackets to the 4 lower holes on the inside of the mesh rails near the bottom on both insides of the crib with

(Part 1) Bolts. Make sure the L-Bracket has the flat side facing upwards and level so the mattress platform can rest on top. See "circles" on

this image for approximate placement of the 4 L-Brackets.

Re-insert (Part C) Mattress Base through the opening in the top of the crib and hold the Mattress Base flat against the top of the L-Brackets using the 2 holes in

the platform to help you handle. Then from the underside of the crib, attach (Part 1) Bolts through the bottom of the L-Bracket and into the corresponding holes

in each of the 4 corners of the Mattress Base.

Attach L-Brackets to Mesh Rails Attach L-Brackets to Mattress Base

Page 9

Helpful Hint: If legs are attached, remove legs first and then install mattress platform, and then re-install legs.