Brizo 63005 Series User manual

SINGLE HANDLE PULLOUT
KITCHEN FAUCETS
T
E
F
L
O
N
Write purchased model number here.
Models
63005 & 63305
Series
ASME A112.18.1 / CSA B125.1
®
1
50150 Rev. B
For easy installation of your Brizo®
faucet you will need:
• To READ ALL the instructions
completely before beginning.
• To READ ALL warnings, care, and
maintenance information.
• To purchase the correct water
supply hook-up.
You may need the following tools:
WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE DISHWASHERS!
SILICONE
T
E
F
L
O
N
5/16/07
SILICONE
T
E
F
L
O
N
T
E
F
L
O
N
®
UPC

2
All parts and finishes of the Brizo® faucet are
warranted to the original consumer purchaser to
be free from defects in material & workmanship
for as long as the original consumer purchaser
owns their home. Delta Faucet Company
recommends using a professional plumber for
all installation & repair.
Delta will replace, FREE OF CHARGE,
during the warranty period, any part or finish
that proves defective in material and/or
workmanship under normal installation, use
and service. Replacement parts may be
obtained by calling 1-877-345-BRIZO (2749)
(in the U.S. and Canada) or by writing to:
In the United States:
Delta Faucet Company
Product Service
55 E. 111th Street
Indianapolis, IN 46280
In Canada:
Masco Canada Limited, Plumbing Group
Technical Service Centre
420 Burbrook Place
London, ON N6A 4L6
This warranty is extensive in that it covers
replacement of all defective parts and even finish,
but these are the only two things that are
covered. LABOR CHARGES AND/OR DAMAGE
INCURRED IN INSTALLATION, REPAIR, OR
Lifetime Faucet and Finish Limited Warranty
REPLACEMENT AS WELL AS ANY OTHER
KIND OF LOSS OR DAMAGES ARE
EXCLUDED. Proof of purchase (original sales
receipt) from the original consumer purchaser
must be made available to Delta for all warranty
claims. THIS IS THE EXCLUSIVE WARRANTY
BY DELTA FAUCET COMPANY, WHICH DOES
NOT MAKE ANY OTHER WARRANTY OF ANY
KIND, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY.
This warranty excludes all industrial, commercial
& business usage, whose purchasers are hereby
extended a five year limited warranty from the
date of purchase, with all other terms of this
warranty applying except the duration of the
warranty. This warranty is applicable to Brizo®
faucets manufactured after January 1, 1995.
Some states/provinces do not allow the exclusion
or limitation of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you. Any damage to this faucet
as a result of misuse, abuse, or neglect, or any
use of other than genuine Delta® replacement
parts WILL VOID THE WARRANTY.
This warranty gives you specific legal rights, and
you may also have other rights which vary from
state/province to state/province. It applies only for
Brizo® faucets installed in the United States of
America, Canada, and Mexico.
© 2007 Masco Corporation of Indiana
TABLE OF CONTENTS:
Warranty -------------------------------------------------------------Page 2
Installation Instructions ----------------------------------------------- Pages 3-9
Maintenance -------------------------------------------------------- Page 10
Replacement Parts -------------------------------------------------- Pages 11&12

2
1
3
Faucet Installation - Center Mount
SHUT OFF WATER SUPPLIES.
Remove old faucet. Make sure hex
opening (1) on hub base (2) is
properly aligned with the hex key
inside of hub. Install round
escutcheon (3) and base ring (4)
onto faucet (5). WARNING! Failure
to install the base ring (4) will
result in damage to the product.
A.
Insert faucet through gasket (1) and
mounting hole in sink making sure
the notches (2) are properly aligned
in base ring.
Push faucet as far back on sink as
possible to allow room for hose. Snap
mounting bracket (1) and bag bracket
(2) together. Secure faucet to sink with
brackets (1) & (2) and nut (3). Tighten
securely using supplied wrench (4).
Note 1: The wrench provided is
designed to be used with a variety of
tools: flat/phillips head screwdrivers,
wrenches, etc.
Note 2: For thin gauge sinks
(not recommended), use the thin deck
aid (5) RP37490 as shown for single
and 3 hole installations to help support
the deck. Call 1-877-345-BRIZO (2749)
to request for free.
C.
A. C.
B.
3
1
4
1
21
2
3
4
5
B.

1
4
SHUT OFF WATER SUPPLIES
Remove old faucet. Place baseplate
shanks (1) through mounting holes
in deck. Option: If sink is uneven, use
silicone sealant under the baseplate.
Place base ring (2) onto baseplate
making sure the notches (3) are
properly aligned and hole (4) is
toward the back. WARNING! Failure
to install the base ring (2) will
result in damage to the product.
A.
Push faucet as far back as possible
to allow room for hose. Snap
mounting bracket (1) and bag
bracket (2) together. Secure faucet
to sink with brackets (1) & (2) and
nut (3). Tighten securely using
supplied wrench (4). Note: The
wrench provided is designed to be
used with a variety of tools:
flat/phillips head screwdrivers,
wrenches, etc. Install locknuts (5)
and hand-tighten.
C.
B. Make sure hex opening (1) on hub
base (2) is properly aligned with the
hex key inside of hub. Place
escutcheon (3) over base ring and
baseplate. Insert faucet down
into escutcheon assembly.
Faucet Installation - Deck Mount (Optional)
2
1
1
3
3
1
2
31
2
3
4
5
5
A. C.
B.
4

2
5
Install hose lead (1) onto hose (2).
Pass hose (2) through faucet (3).
Spout Hose Installation
A.
B. Remove and discard hose lead (1).
Snap clip (4) to hose. Be sure clip
is oriented as illustrated.
Attach hose by firmly pushing onto
valve shank (5) (at back of valve)
until it clicks.
C.
A. B.
C.
5
2
4
5
1
2
2
1
1
3

3
6
CAUTION: Extreme care must be
exercised in bending copper inlet
tubes to avoid kinking. Follow these
instructions exactly. Kinked tubes will void
the warranty.
Gently push tubes (1) to the back of the
mounting bracket (2). Spread the tubes to
desired position by grabbing near the top
Supply Line Connections
of the tubes. Make connections to water
lines. Use 1/2” IPS faucet connections
(A) (not provided), or use coupling nuts
with 3/8” O.D. ball-nose risers (B).
Important: Use two wrenches when
tightening. Do not overtighten.
1
2
1/2" (12.70mm) IPS
1
AB

4
7
Separate head (1) from body assembly
(2). Make sure gasket (3) is properly
seated in the base of the body assembly.
Insert body assembly through selected
hole in sink. From under the sink secure
body assembly to sink with nut (4). Screw
the bottle (5) onto the body assembly
shank. Insert pump (6) down into the
body assembly, then attach head
assembly (1) to pump.
Soap Dispenser Installation
Note: To fill, lift the head and pump
assembly out of the bottle and pour
not more than 8 oz. into bottle. DO
NOT remove the bottle each time as
this weakens the neck. Use a funnel to
help prevent spills. Pull pump and head
assembly out occasionally to soak and
pump warm water through pump to
remove soap build-up.
1
2
3
4
5
6

5
8
Flush the System and Check for Leaks
1
2
3
3
14"
(356 mm)
Min.
6
4
5
Install weight before bottom
loop with wand in nest.
A. B.
Pull the hose assembly (1) out of the
spout and be sure to hold the end of
the hose down into the sink. Move
faucet handle (2) to the full on mixed
position. Turn on hot and cold water
supplies (3) and flush water lines for
one minute. Important: This flushes
away any debris that could cause
damage to internal parts.
Check all connections at arrows for
leaks. Re-tighten if necessary, but do
not overtighten.
A. Thread the hose nut (4) into the
wand assembly (5) and tighten
securely. It can be helpful to use a
rubber sheet type jar opener to
tighten the hose nut. This helps to
ensure that the hose nut will not
loosen over time.
Attach zinc weight (6) to hose
assembly as shown with wand
in nest.
B.

6
The purpose of the bag is to help prevent
the hose from catching on supply lines or
other items below the sink and to provide
a place to keep your product literature
and tools.
Install the bag (1) as shown. Note: The
bag can be positioned on any of the
provided holes to allow for obstacles
Bag Installation
below the sink. You should try to position
the bag to allow the best possible
envelope for the hose assembly given
the circumstances below the sink. It is
possible in some installations the bag may
not be able to be used. Place tools and
installation/maintenance sheet (2) in the
bottom of the bag for safe keeping.
1
2
9

If faucet leaks from under handle:
Remove handle and ensure cap (1) is tight.
If leak persists–SHUT OFF WATER
SUPPLIES. Replace valve cartridge (2).
If faucet leaks from spout outlet–SHUT
OFF WATER SUPPLIES. Replace valve
cartridge (2).
Maintenance
10
1
2
Your Delta Faucet pull-out spout
incorporates a backflow protection system
that has been tested to be in compliance
with ASME A112.18.3 and
ASME A112.18.1 / CSA B125.1. It
incorporates two certified check valves in
series, which operate independently and
are integral, non-serviceable parts of the
wand assembly.
Backflow Protection System
Note: A small amount of water may run
out the spout or drip for a very short
period after the faucet is shut off. This is
a natural occurrence caused by the long
flexible hose.