Buyers LT30 User manual

LT30 Gas Gan Rack
for Utility Landscape Trailers
Holds one 5 gal. gas can or lwo 2-1.12 gal, gas cans.
Important!
Before you begin installing:
1. Read and understand these instructions
completely.
2. Vedfy that you have received all the parts
Iisted in the bill of materials.
CAUTION:
Always wear safety glasses when using power tools.
Utility Trailer Installation Instructions
THRIAD STRAP THROUGH
RACK AS SHOlvN HIRT
IRAILIR RAIL
TRA I LI
Tools Required:
,911.6" Wrench or Socket
,7132" Hexagon Allen Wrench
rElectric Drill
tI3l32" Drill Bit
1. Place the gas can rack on the rail of your util-
ity trailer where you would like it mounted. Make
sure the rack does not extend past the widest
part of the trailer. Align the holes in the bottom
of the gas can rack with the center of the rail.
You may need to adjust the position of the rack
so the four slots in the bottom are clear of any
obstruction.
2. Mark the position of the two holes on the
trailer rail.
WARNING! Check for locations of brake lines
and electrical wiring etc., beJorg drilling any
holes. Any damage to trailer during installation
is the installer's sole responsibility.
3. Drill 1.3/32'holes in the positions marked.
Bill of Materials
ITEM PART NO. DESCRIPTION
1 3004328 IGas Can. Rack
2 3OO471O I Strap,60"
3 - 4 Washer. Flat 3/B USS Zn
2 Screw Button Socket Head Cap, 3/8-16 x 1-1/4
2 Nut, Nvlock 3/8-16 x7/167n
4. Bolt the rack to the trailer with two 3/8-1,6
x1,-1,14 socket head cap screws, four 3/8" flat
washers, and two 3/8-16 nylock nuts supplied
and tighten.
5. Thread the fiqe epd of the strap through the
rack as shown for holding lwo 2-1/2 gal. cans or
thread the strap into the other slots for holding
one 5 gal. can. Then thread the buckle onto the
end of the strap as shown.
-continued on other side

OUTSIDT TRAITER IYATL
IVALT SUPPORT STU
3/4'THtCI(
SHIM STRIPS
Enclosed Trailer Installation Instructions
Tools and Materials Required:
.9/16" Wrench or Socket
t7/32" Hexagon Allen Wrench
.Electric Drill
.1/4" Drill Bit
.3/4" Plywood Shim Stdps
rShim Screws
1. Assemble the gusset bracket to the gas can rack with
two 3/B-16 x 1.-1.14 socket head cap screws, four 3/8" flat
washers and two 3/B-16 nylock nuts supplied.
2. In order to mount this rack to an enclosed trailer, you
must first add 3/4" plywood shim strips to the walls.
These shim strips must be attached to at least two wall
support studs with suitable fasteners. If you don't know
what kind or length of fastener to use contact your trailer
dealer or manufacturer for their recommendation.
3. Place the place the gas can rack with gusset against
the shims, hold level, and mark the position of the two
3/8" holes in rack and the two 3/8" gusset holes.
WARNING! Check for locations of brake lines and
electrical wiring etc., before drilling any holes. Any
damage to trailer duying.installation is the installer's
sole responsibility. '
4. Drill f.our 1.14" pilot holes in the positions just marked
for the 3/8" Iag screws. Be extremely careful not to drill
through the outside trailer wall.
Bill of Materials
ITEM PART NO. QTY. DESCRIPTION
I 3004328 I Rack, Cas Can, Rack Onlv
2 3004501 1 Bracket, Cusset, LTl5 & LT30
3 3OO471O I Strap,60" Lashine w/Cam Buckle
4 - B Washer, Flat 3/B USS Zn
5 - 2 Screw Button Socket Head Cap,3/8-16 x 1-ll4
6 - 2 Nut, Nylock 3/8-16 x 716 Zn
7 - 4 Screw, Hex Head Lag, 3/B t
5. Fasten the rack to the trailer wall with the four 3/8"
x 1.-1./4" 1ag screws and four 3/8" flat washers supplied.
6. Thread the free end of the strap through the rack as
shown for holding two 2-112 ga1. cans or thread the strap
into the other siots for holding one 5 gal. can. Then thread
the buckle onto the end of the strap as shown.
Warranty Information
Buyers Products wafiants all truck/trailer hardware
manufactured or distributed by it, to be free from
defects in material and workmanship for a period of
one year from date of shipment. Parts must be pro-
perly installed and used under normal conditions.
Any product which has been altered, including modi-
fication, misuse, accident or lack of maintenance wiil
not be considered under warranty. Normal wear is
excluded. The soie responsibiiity of Buyers Products
under this warranty is limited to repairing or replac-
ing any part or parts which are returned, prepaid, and
are,, found to be defective by Buyers Products.,'
Authonzation from Buyers Products must be obtained
before returning any part. No charges for transporta-
tion or labor performed on Buyers' products will be
allowed under this warranty.
THRTAD
\ RACI( STRAP IHROUGH
AS SHotYl,t Ht
3004397 Rev. B