CableWholesale 8212-50005 User manual

8212-50005

NOTE: Read the entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin the installation of the product before you have read and understood the
instructions and warnings contained in this installation sheet. If you have any questions
regarding any of the instruction or warning, please contact your local distributor.
• Please refer to installation guide recommendation for required distance from wall to
avoid risk of property damage.
• This product should only be installed by someone of good mechanical aptitude, with
experience and basic building, and fully understands.
• Make sure that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
• Never exceed the maximum load capacity.
• If mounting to wood wall studs, make sure that mounting screws are anchored into
the center of the studs. Use of an “edge to edge” stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the items,
greatly reducing their holding power.
• This products intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
21
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone the special franchiser for a replacement.
Package M
Package W
Tools required
Phillips head screw driver(200mm length exclude the handle)
Electric drill and 10mm masonry bit for concrete wall installation
Marking pen
Hammer
·
·
·
·
·
M6 socket and wrench
ST6.3x55 (x6)
W-A
lag bolt concrete anchor
W-B
(x6) D (ø xø )
(x6)
6 6.3 16
washer
W-C
M4x10
M-A
(x4) M5x10 (x4)
M-B
D4 ( 4.5x )
washer
M-E
ø ø10
(x4)
D (ø .5xø )
(x4)
5 5 12
washer
M-F
M6x10 (x4)
M-C
D6 (ø6.3xø )
(x4)
16
washer
M-G
M8x15 (x4)
M-D
D8 (ø8.3xø )
(x5)
16
washer
M-H
ø13.5xø5.5x3.2 (x4)
M-I
decorative cover 1 (x1)
C
left decorative cover (x1)
Gright decorative cover (x1)
H
wall plate(x1)
A
adapter bracket (x1)
B
grip holder (x1)
I
M8 (x1)
M-J
M8 (x2)
M-K
M8x20 (x1)
M-L
M8x50 (x1)
M-M
M8 (x1)
M-N
decorative cover 2 (x1)
D
decorative cover 3 (x1)
Edecorative cover 4 (x1)
F
washer (x1)
M-O

43
Wood Stud Wall Mounting:
1a
WARNING
• Make sure that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
• Tighten wood screws firmly, but do not over tighten. Over tightening can damage
the screws, greatly reducing their holding power.
• Make sure that mounting screws are anchored into the center of the studs. Use of
an “edge to edge” stud finder is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall
or plaster into studs. Installers are responsible to provide hardware for other types
of mounting situations.
fig. 1.1
WARNING
• When installing wall mounts on cinder block, verify that you have a minimum of
1-3/8” of actual concrete thickness in the hole to be used for the concrete anchors.
Do not drill into mortar joints! Be sure to mount in a solid part of the block,
generally 1” minimum from the side of the block. It is suggested electric drill on
slow setting is used to drill the hole instead of a hammer drill to avoid breaking out
the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
Solid Brick And Concrete Block Mounting:
1b
• Use the wall plate as a template to mark six holes locations on the wall, as shown in fig.1.2.
• Pre-drill these holes with a 10mm masonry bit to at least 60mm in depth. Insert a concrete anchor (W-B)
into each of these holes. Attach the wall plate to the wall using six wood screws (W-A) and six washers
(W-C), as shown in fig.1.3.
• Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended.
Based on their edges, draw a vertical line down each stud’s center.
• Place wall plate on wall as a template. And mark the center of the two mounting holes. Make sure that the
mounting holes are on the stud centerline.
• Drill two 1/8” (3mm) dia. Holes 1.2” (30mm) deep. Make sure that the wall plate is level, secure it using
two screws (W-A) and two washers(W-C) as shown in fig. 1.1.
Stud
W-A
W-C
fig. 1.2 fig. 1.3
• Assemble the adapter bracket with appropriate parts as shown in fig.2.1.
• Assemble the adapter bracket and arm of wall plate with appropriate screw, washers and nut. As shown
in fig.2.2.
2Adapter Bracket Mounting
W-A
W-B
W-C

65
Installing the Display
• Find the appropriate VESA, attach the adapter plate to the back of the screen using the appropriate
combination of screws, washers, as shown in fig.4.1 and fig.4.2.
• Begin with the proper screw, hand thread through washer and adapter plate into screen as shown below.
• Screw must make at least three full turns into mounting hole and snug fit into place. Do not over tighten.
• Repeat for remaining mounting holes, level plate and tighten screws.
4
• Cut off the corner of the decorative cover for easy to the cable management and then run power cable
through the hole of decorative cover.
• Snap the decorative covers from left and right to cover the wall plate rails and the bracket arm as shown in
fig. 3.1.
3Cable Management and Decorative Covers Mounting
fig. 2.1
fig. 2.2
M-L
fig. 4.1
fig. 4.2
M-C
M-D
M-G
M-H
M-A
M-B
M-I
M-E
M-F
M-J
M-M
M-K
M-K
fig. 3.1
M-N
M-H
M-O