Celexon VKS2040 User manual

Operating instructions
celexon PTZ Camera Full HD Video
Conference System VKS2040
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully before
connecting or operating this product. Please retain these instructions for future use.
Version: 32422_051

1
Please read and follow all the safety instructions below and on the product before
connecting the camera to a power source. Failure to comply with the safety instructions
may result in re, electric shock, or personal injury, and could affect the safety features
contained in the unit. Please retain all safety instructions.
• All accessories and cables must be removed before transporting the camera.
• Do not grasp the camera head when transporting the camera.
• Always use the remote control to turn the camera head. Do not turn the camera
head by hand. You risk mechanical damage.
• When turning the camera, make sure that there are no obstacles within the camera‘s
turning range.
• The camera may only be operated with the power pack supplied.
• Do not expose the camera to direct sunlight or to damp, greasy or dusty places or
where the camera could come into contact with rain, smoke or steam.
• Never expose this equipment or its components to rain or moisture to reduce the
risk of re or electric shock.
• Do not drop the camera.
• Do not spill liquids on the camera.
• Do not place sources of open ames, such as lit candles.
• Do not use the camera in extremely bright conditions for long periods of time.
• The camera must not be used in the vicinity of strong electromagnetic radiation, e.g.
televisions and radio transmitters. The specic frequency of electromagnetic elds
can affect the camera image.
• Use the supplied power cable. Connect the power cable to a socket with a
protective earth connection. It is recommended to use a multiple socket outlet with
surge protection. The wall sockets must not be overloaded.
• The camera must not be installed in places subject to mechanical vibrations.
• The camera must not be placed on an unstable surface. This could result in
serious personal injury and camera damage. When mounting the camera on a tripod,
make sure that you follow the manufacturer‘s instructions. Use only the mounting
materials recommended by the manufacturer.
• When unplugging the power cable, hold the plug and not the cable.
• Make sure that no one steps on the power cable especially at the power socket, or
at the connection point to the camera.
• Unplug the camera if you will not be using it for a long period of time.
SAFETY INSTRUCTIONS

2
• The camera must not be used outside the specied temperature,humidity and
power ranges.
• Unplug the camera from the mains if you need to clean it. Only use a soft, dry cloth
to clean the camera and camera lens. Never use alcohol, solvents or ammonia-based
liquids on this camera.
• Wash your hands after handling the cables supplied with this camera.
• The remote control of the camera uses batteries. Make sure that the polarity of
the batteries (+/-) is correctly aligned. Dispose of used batteries according to local
disposal regulations.
• Repairs may only be carried out by qualied personnel. The cover must not be
removed. Unauthorised maintenance of your camera can be dangerous and will
invalidate the warranty.
• Only use spare parts specied by celexon. Unauthorised spare parts could cause
re, electric shock or personal damage and will invalidate the warranty.
• Follow these instructions to ensure image quality throughout the life of the camera.
Failure to follow these instructions may invalidate the warranty.
• Should you notice any external damage to the unit or unexpected or unusual
operation, do not continue to use the product. In these cases switch off the
productimmediatelyanddisconnectitfromthepowersupply.Immediatelycontactthe
dealer from whom you purchased the product or celexon directly (Web:
www.celexon.co.uk, Mail: [e-mail]) for further information.
• Failure to follow the above instructions may result in personal injury or damage to
the product or equipment connected to it. Incorrect installation or use may also be
invalidated if the product is installed or used incorrectly.
• If you are unsure about the use of the product, contact a professional, your dealer or
celexon directly. (Web: www.celexon.co.uk, Mail: [e-mail]).
• Technical changes and errors are possible.
The manufacturer accepts no responsibility for damage to property or personal injury
if the product is used outside the recommended specications or if it is improperly
installed.
DISCLAIMER
The information in this document is subject to change without notice by the
manufacturer.
Changes will be added to subsequent versions of this manual. The manufac-
turer does not guarantee or warranty for the correctness of the information in
this document.

3
IN THE BOX
1x PTZ camera 1x 12V power supply unit1x IR remote control 1x Microphone &
Loudspeaker
2x USB 2.0 cable
CAMERA PARAMETERS
Zoom 10x
Image Sensor 1/ 2.8“ Exmor CMOS
Pixels 2.7 Megapixel
HOV 72°
Resolution 1920x1080@30fps // 1280x720 // 640x480
640x360 // 352x288 // 320x240
Min. Illu 0.[email protected]
Electricity Commuication
Power supply DC12V Transmission Rate 2400/4800/9600/
19200/38400
Power
consumption 12W Protocol VISCA/PELCO-D
PELCO-P
Decoder Built in Address insettings 1-255
Operation Surroundings
Pivot rotation -178°~ +178° Surroundings 115 x 115 x 135 mm
Tilt rotation -30°~ +90° Operating
temperature -10°C ~ +50°C
Memory
Remote control max. 9
memory locations Weight 1.2 kg
A total of up to max.
255 memory locations
possible
Installation
possibilities Wall/Ceiling/Tripod

4
PTZ CAMERA IN DETAIL
Lens
IR receiver eye
On / Off indicator
RS232 connector
USB 2.0 port
DC12V power connector
Mute
Quieter
Louder
REMOTE CONTROL FUNCTIONS
Power On / Standby
P/T RST Camera starts alignment
FLIP Camera image is rotated
Camera Select Select the camera to be
controlled
BLC Switch BLC on/off
MENU Open / Close Menu
Navigation Home = Align camera centrally
PRESET Preset + number 1-9 = preset save
RESET Reset + number 1-9 = reset stored preset
FOCUS Auto = auto. Focus
Manual = manual focus
Far = manu. Focus, background in focus
Near = manu. Focus, foreground in focus
ZOOM + zoom in
- zoom out
Numbers Memory locations 1-9

5
INSTALLATION
Always connect the camera in the same way, regardless of whether the camera
is connected to a permanently installed PC or a mobile laptop.
1) Connect the camera to the DC12V power supply and plug it in to power.
As soon as the LED (3) lights up, the camera is switched on and ready for
operation.
Note: Make sure that the camera is free of packaging material and that no
objects are blocking the camera‘s range of movements. The camera will centre
itself in the beginning. It is not necessary to align the camera by hand.
2) Connect the camera with the USB A-A cable and connect it to the PC.
Optionally, the camera can also be controlled with an RS232 data cable
(DIN8M) (not included in the box).
3) Connect the microphone & loudspeaker module with the other USB cable to
a free USB port on your PC.
4) As soon as the PC has recognised the camera and microphone & loudspe-
aker module, the conference system can be started. The system can be used
with all common video conferencing programs.

6
Manufacturer: celexon Europe GmbH
Adress: Gutenbergstraße 2, 48282 Emsdetten, DE
Productname: celexon PTZ Camera Full HD
Video Conference System VKS2040
Products that are marked with the UKCA mark meet all requirements of
the relevant UK directives. The UK declaration of conformity can be downloaded
at the following address at: www.celexon.de/zertikate
INFORMATION ON UK CONFORMITY
The symbol indicates the separate collection of electrical and electronic
equipment in EU countries. Please do not throw the appliance into the
household waste. Please nd out about the take-back system in force
in your country and if you have any questions about them, contact your
local municipality or your local recycling and hazardous waste collection
centre.