Central Pneumatic 61718 User manual

Page 2 For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 . Item 61718
SAFETY OP ER ATION MAINTENANCESETU P
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 6
Setup .......................................................... 7
Operation................................................... 10
Maintenance.............................................. 12
Parts List and Diagram.............................. 14
Warranty .................................................... 16
W AR NING SY MBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMP OR TANT SAFETY INSTR U CTIONS
INSTR U CTIONS P ER TAINING TO A R ISK OF FIR E,
ELECTR IC SHOCK, OR INJU R Y TO P ER SONS
W AR NING – When using tools, basic precautions should always be followed, including the following:
General
To reduce th e risk s of electric sh ock ,
f ire, and inj ury to persons, read all th e
instructions bef ore using th e tool.
W ork Area
1. Keep th e w ork area clean and w ell lig h ted.
Cluttered benches and dark areas increase the
risks of electric shock, fire, and injury to persons.
2. Do not operate th e tool in ex plosiv e
atm osph eres, such as in th e presence
of f lam m able liq uids, g ases, or dust.
The tool is able to create sparks resulting
in the ignition of the dust or fumes.
3. Keep bystanders, children, and visitors away
while operating the tool. Distractions are
able to result in the loss of control of the tool.

Page 3For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 .Item 61718
SAFETYOP ER ATIONMAINTENANCE SETU P
P ersonal Saf ety
1. Stay alert. Watch what you are doing and
use common sense when operating the tool.
Do not use the tool while tired or under the
influence of drugs, alcohol, or medication.
A moment of inattention while operating the
tool increases the risk of injury to persons.
2. Dress properly . Do not w ear loose
cloth ing or j ew elry . Contain long h air.
Keep h air, cloth ing , and g lov es aw ay f rom
m ov ing parts. Loose clothes, jewelry, or long
hair increases the risk of injury to persons as
a result of being caught in moving parts.
3. Av oid unintentional starting . Be sure th e sw itch
is of f bef ore connecting to th e air supply .
Do not carry the tool with your finger on the switch or
connect the tool to the air supply with the switch on.
4. R em ov e adj usting k ey s and w rench es
bef ore turning th e tool on. A wrench or a
key that is left attached to a rotating part of the
tool increases the risk of personal injury.
5. Do not ov erreach .
Keep proper f ooting and balance at all tim es.
Proper footing and balance enables better
control of the tool in unexpected situations.
6. U se saf ety eq uipm ent.
A dust mask, non-skid safety shoes
and a hard hat must be used for the
applicable conditions.
7. Alw ay s w ear ey e protection.
Wear ANSI-approved safety goggles.
8. Alw ay s w ear h earing protection
w h en using th e tool.
Prolonged exposure to high intensity
noise is able to cause hearing loss.
Tool U se and Care
1. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against the body is
unstable and is able to lead to loss of control.
2. Do not f orce th e tool. Use the correct tool for the
application. The correct tool will do the job better
and safer at the rate for which the tool is designed.
3. Do not use th e tool if th e sw itch does
not turn th e tool on or of f . Any tool that
cannot be controlled with the switch is
dangerous and must be repaired.
4. Disconnect th e tool f rom th e air source
bef ore m ak ing any adj ustm ents, ch ang ing
accessories, or storing th e tool. Such preventive
safety measures reduce the risk of starting the
tool unintentionally. Turn off and detach the air
supply, safely discharge any residual air pressure,
and release the throttle and/or turn the switch to
its off position before leaving the work area.
5. Store the tool when it is idle out of reach
of children and other untrained persons.
A tool is dangerous in the hands of untrained users.
6. Maintain th e tool w ith care. Keep a cutting
tool sharp and clean. A properly maintained
tool, with sharp cutting edges reduces the
risk of binding and is easier to control.
7. Ch eck f or m isalig nm ent or binding of m ov ing
parts, break ag e of parts, and any oth er condition
th at af f ects th e tool' s operation. If damaged,
have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
There is a risk of bursting if the tool is damaged.
8. U se only accessories th at are identif ied by th e
m anuf acturer f or th e specif ic tool m odel. Use of
an accessory not intended for use with the specific
tool model, increases the risk of injury to persons.
Serv ice
1. Tool service must be performed only
by qualified repair personnel.
2. W h en serv icing a tool, use only identical
replacem ent parts. U se only auth orize d parts.
3. U se only th e lubricants supplied w ith th e
tool or specif ied by th e m anuf acturer.

Page 4 For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 . Item 61718
SAFETY OP ER ATION MAINTENANCESETU P
Air Source
1. Nev er connect to an air source th at
is capable of ex ceeding 2 0 0 psi.
Over pressurizing the tool may cause
bursting, abnormal operation,
breakage of the tool or serious injury
to persons. Use only clean, dry, regulated
compressed air at the rated pressure or within the
rated pressure range as marked on the tool.
Always verify prior to using the tool that the air
source has been adjusted to the rated air pressure
or within the rated air-pressure range.
2. Never use oxygen, carbon dioxide, combustible
gases or any bottled gas as an air source
for the tool. Such gases are capable of
explosion and serious injury to persons.
SAV E THESE INSTR U CTIONS.
Sy m bols and Specif ic Saf ety Instructions
Sy m bol Def initions
Sy m bol P roperty or statem ent
noNo-load speed
.../m in Revolutions or reciprocation per minute
P SI Pounds per square inch of pressure
f t-lb Foot-pounds of torque
BP M Blows per minute
CFM Cubic Feet per Minute flow
SCFM Cubic Feet per Minute flow
at standard conditions
Sy m bol P roperty or statem ent
NP T National pipe thread, tapered
NP S National pipe thread, straight
WARNING marking
concerning Risk of Eye Injury.
Wear ANSI-approved eye protection.
WARNING marking concerning Risk of
Hearing Loss. Wear hearing protection.
WARNING marking concerning
Risk of Respiratory Injury. Wear
NIOSH-approved dust mask/respirator.
WARNING marking concerning
Risk of Explosion.

Page 5For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 .Item 61718
SAFETYOP ER ATIONMAINTENANCE SETU P
Specif ic Saf ety Instructions
1. The amount of actual torque may vary depending
on the cleanness and condition of the threads and
other factors. If tightening critical components,
check the actual torque applied to the fastener
with a mechanical torque wrench (not supplied).
2. The warnings and precautions discussed in this
manual cannot cover all possible conditions and
situations that may occur. It must be understood
by the operator that common sense and caution
are factors which cannot be built into this
product, but must be supplied by the operator.
3. WARNING: The brass components of
this product contain lead, a chemical
known to the State of California to cause
birth defects (or other reproductive harm).
(California Health & Safety Code § 25249.5, et seq.)
4. Only use with accessories rated to handle the
forces exerted by this tool during operation.
Other accessories not designed for the forces
generated may break and forcefully launch pieces.
5. Attach all accessories properly to the tool before
connecting the air supply. A loose accessory
may detach or break during operation.
6. Obey the manual for the air compressor
used to power this tool.
7. Install an in-line shutoff valve to allow
immediate control over the air supply in an
emergency, even if a hose is ruptured.
8. Use this tool with both hands only. Using tools
with only one hand can result in loss of control.
9. Do not lay the tool down until it has come to
a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
V ibration P recautions
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for
an extended period should first be examined
by a doctor and then have regular medical
check-ups to ensure medical problems are not
being caused or worsened from use. Pregnant
women or people who have impaired blood
circulation to the hand, past hand injuries,
nervous system disorders, diabetes, or Raynaud's
Disease should not use this tool. If you feel
any symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
7. To reduce vibration, maintain
tool as explained in this manual.
If abnormal vibration occurs, stop immediately.
SAV E THESE INSTR U CTIONS.

Page 6 For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 . Item 61718
SAFETY OP ER ATION MAINTENANCESETU P
Functional Description
Specif ications
Maximum Air Pressure 90 PSI
Air Inlet 1/4″ -18 NPT
Rated Speed* 7,000 RPM
Average Air Consumption 5 CFM @ 90 PSI
Arbor/Chuck Capacity 1/2″
* Rated speed at stated maximum air pressure.
Excess air pressure is hazardous and
may cause the tool to exceed stated rated speed.
Com ponents and Controls
Anv il
Trig g er
Air R eg ulator
Control
V alv e
Air Inlet

Page 7For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 .Item 61718
SAFETYOP ER ATIONMAINTENANCE SETU P
Initial Tool Set U p/ Assem bly
R ead th e ENTIR E IMP OR TANT SAFETY INFOR MATION section at th e beg inning of th is
m anual including all tex t under subh eading s th erein bef ore set up or use of th is product.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Note: This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up.
Air Supply
TO P R EV ENT SER IOU S INJU R Y FR OM EX P LOSION:
U se only clean, dry , reg ulated, com pressed air to pow er th is tool.
Do not use ox y g en, carbon diox ide, com bustible g ases,
or any oth er bottled g as as a pow er source f or th is tool.
1. Incorporate a filter, regulator with pressure gauge,
oiler, in-line shutoff valve, and quick coupler for
best service, as shown on Figure A on page 8
and Figure B on page 9. An in-line sh utof f
ball v alv e is an im portant saf ety dev ice because
it controls th e air supply ev en if th e air h ose
is ruptured. Th e sh utof f v alv e sh ould be a
ball v alv e because it can be closed q uick ly .
Note: If an automatic oiler system is not used,
add a few drops of Pneumatic Tool Oil to the airline
connection before operation. Add a few more drops
after each hour of continual use.
2. Attach an air hose to the compressor's air outlet.
Connect the air hose to the air inlet of the tool.
Other components, such as a coupler plug
and quick coupler, will make operation
more efficient, but are not required.
W AR NING! TO P R EV ENT SER IOU S INJU R Y
FR OM ACCIDENTAL OP ER ATION:
Do not install a f em ale q uick coupler on th e tool.
Such a coupler contains an air valve that will
allow the air tool to retain pressure and operate
accidentally after the air supply is disconnected.
Note: Air flow, and therefore tool performance,
can be hindered by undersized air supply components.
The air hose must be long enough to reach
the work area with enough extra length to
allow free movement while working.
3. Turn the tool's throttle or switch to the off position;
refer to Operation section for description of controls.
4. Close the in-line shutoff valve between
the compressor and the tool.
5. Turn on the air compressor according to
the manufacturer's directions and allow it
to build up pressure until it cycles off.
6. Adjust the air compressor's output regulator
so that the air output is enough to properly
power the tool, but the output will not exceed
the tool's maximum air pressure at any time.
Adjust the pressure gradually, while checking the
air output gauge to set the right pressure range.
7. Inspect the air connections for leaks.
Repair any leaks found.
8. If the tool will not be used at this time, turn off
and detach the air supply, safely discharge
any residual air pressure, and release
the throttle and/or turn the switch to its off
position to prevent accidental operation.
Note: Residual air pressure should not be present
after the tool is disconnected from the air supply.
However, it is a good safety measure to attempt to
discharge the tool in a safe fashion after disconnecting
to ensure that the tool is disconnected and not powered.

Page 8 For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 . Item 61718
SAFETY OP ER ATION MAINTENANCESETU P
Fig ure A: P ortable Air Supply Setup
G
A
E
E
H
F
B
Non-lubricated Tools Lubricated Tools
A
B
C
C
DA
Description Function
A Air Hose Connects air to tool
B Filter Prevents dirt and condensation from damaging tool or workpiece
C Regulator Adjusts air pressure to tool D Lubricator (optional) For air tool lubrication
E Coupler and Plug Provides quick connection and release
F Leader Hose (optional) Increases coupler life
G Air Cleaner / Dryer (optional) Prevents water vapor from damaging workpiece
H Air Adjusting Valve (optional) For fine tuning airflow at tool

Page 9For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 .Item 61718
SAFETYOP ER ATIONMAINTENANCE SETU P
Fig ure B: Stationary Air Supply Setup
N
L
L O
M
C C
Non-lubricated Tools
Lubricated Tools
H
I
I
J
JKH
F
G
E
Slope
F
F
B
B
A
A
CD
Description Function
A Vibration Pads For noise and vibration reduction
B Anchor Bolts Secures air compressor in place
C Ball Valve Isolates sections of system for maintenance D Isolation Hose For vibration reduction
EMain Air Line - 3/4″ minimum recommended Distributes air to branch lines
F Ball Valve To drain moisture from system
GBranch Air Line -1/2″ minimum recommended Brings air to point of use
H Air Hose Connects air to tool
I Filter Prevents dirt and condensation from damaging tool or workpiece
J Regulator Adjusts air pressure to tool
K Lubricator (optional) For air tool lubrication
L Coupler and Plug Provides quick connection and release
M Leader Hose (optional) Increases coupler life
N Air Cleaner / Dryer (optional) Prevents water vapor from damaging workpiece
O Air Adjusting Valve (optional) For fine tuning airflow at tool

Page 10 For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 . Item 61718
SAFETY OP ER ATION MAINTENANCESETU P
Operating Instructions
R ead th e ENTIR E IMP OR TANT SAFETY INFOR MATION section at th e beg inning of th is
m anual including all tex t under subh eading s th erein bef ore set up or use of th is product.
Inspect tool bef ore use, look ing f or dam ag ed, loose, and m issing parts.
If any problem s are f ound, do not use tool until repaired.
Tool Set U p
TO P R EV ENT SER IOU S INJU R Y FR OM ACCIDENTAL OP ER ATION:
Turn of f th e tool, detach th e air supply , saf ely disch arg e any residual air pressure
in th e tool, and release th e th rottle and/ or turn th e sw itch to its of f position bef ore
perf orm ing any inspection, m aintenance, or cleaning procedures.
TO P R EV ENT SER IOU S INJU R Y :
Do not adj ust or tam per w ith any control or com ponent in a w ay not specif ically ex plained w ith in
th is m anual. Im proper adj ustm ent can result in tool f ailure or oth er serious h aza rds.
1. Push the Control Valve forward so that the end
of the Valve protrudes out above the Trigger
for clockwise (″forward″) tool operation.
2. Push the Control Valve back so that the end of
the Valve protrudes from the back of the Housing
for counterclockwise (″reverse″) tool operation.
3. Adjust air flow by pushing down Air Regulator and
turning knob from positions 1 through 4, aligning
desired number setting with the recessed arrow.
• Position 1 allows the lowest amount of air flow.
• Position 4 allows the highest amount of air flow.
4. Push and snap the required 1/2″ drive
impact socket (not included) onto the Anvil.
CAU TION! Only use im pact rated accessories
w ith th is tool. Other accessories may
shatter, chip, or crack during operation.
W ork piece and W ork Area Set U p
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
2. Route the air hose along a safe route to reach
the work area without creating a tripping hazard
or exposing the air hose to possible damage.
The air hose must be long enough to reach
the work area with enough extra length to
allow free movement while working.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be hazardous objects
(such as utility lines or foreign objects) nearby
that will present a hazard while working.

Page 11For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 .Item 61718
SAFETYOP ER ATIONMAINTENANCE SETU P
General Operating Instructions
1. If an automatic oiler is not used, add a few
drops of Pneumatic Tool Oil to the airline
connection before use. Add a few drops
more after each hour of continual use.
2. Connect the air hose to the air inlet of the tool.
3. If tightening the nut, tighten by hand
as much as possible first.
4. Place the socket over the nut.
5. Grip the Impact Wrench firmly with two
hands and squeeze the Trigger.
6. If the tool requires more force to accomplish
the task, verify that the tool receives sufficient,
unobstructed airflow (CFM) and increase the
pressure (PSI) output of the regulator up to the
maximum air pressure rating of this tool.
CAU TION! TO P R EV ENT INJU R Y FR OM
TOOL OR ACCESSOR Y FAILU R E:
Do not ex ceed th e tool' s
m ax im um air pressure rating .
If the tool still does not have sufficient force
at maximum pressure and sufficient airflow,
then a larger tool may be required.
7. The amount of actual torque may vary depending
on the cleanness and condition of the threads and
other factors. If tightening critical components,
check the actual torque applied to the fastener
with a mechanical torque wrench (not supplied).
8. To prevent accidents, turn off the tool, detach
the air supply, safely discharge any residual air
pressure in the tool, and release the throttle and/
or turn the switch to its off position after use.
Clean external surfaces of the tool with clean,
dry cloth, and apply a thin coat of tool oil.
Then store the tool indoors out of children's reach.

Page 12 For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 . Item 61718
SAFETY OP ER ATION MAINTENANCESETU P
U ser-Maintenance Instructions
P rocedures not specif ically ex plained in th is m anual m ust
be perf orm ed only by a q ualif ied tech nician.
TO P R EV ENT SER IOU S INJU R Y FR OM ACCIDENTAL OP ER ATION:
Turn of f th e tool, detach th e air supply , saf ely disch arg e any residual air pressure
in th e tool, and release th e th rottle and/ or turn th e sw itch to its of f position bef ore
perf orm ing any inspection, m aintenance, or cleaning procedures.
TO P R EV ENT SER IOU S INJU R Y FR OM TOOL FAILU R E:
Do not use dam ag ed eq uipm ent. If abnorm al noise, v ibration,
or leak ing air occurs, h av e th e problem corrected bef ore f urth er use.
TO P R EV ENT SER OU S INJU R Y FR OM EX P LOSION:
Lubricate th e tool only w ith specif ied lubricants. Lubricate th e air inlet using only
pneum atic tool oil. Oth er lubricants m ay dam ag e th e m ech anism and m ay be
h ig h ly f lam m able, causing an ex plosion.
Cleaning , Maintenance, and Lubrication
Note: These procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the air-operated tool.
1. BEFOR E EACH U SE, inspect the general
condition of the tool. Check for:
• loose hardware or housing,
• misalignment or binding of moving parts,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
2. Daily - Air Supply Maintenance:
Every day, maintain the air supply according
to the component manufacturers' instructions.
Maintain the lubricator's oil level.
Drain the moisture filter regularly.
Performing routine air supply maintenance
will allow the tool to operate more safely
and will also reduce wear on the tool.
3. W eek ly – Lubrication:
Add a high quality machine oil to the oil inlet by
removing the Oil Screw.
4. Q uarterly ( ev ery 3 m onth s) –
Tool Disassem bly , Cleaning , and Inspection:
Have the internal mechanism cleaned, inspected,
and lubricated by a qualified technician.
Fig ure C
Oil Screw
Oil Inlet

Page 13For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 .Item 61718
SAFETYOP ER ATIONMAINTENANCE SETU P
Troublesh ooting
P roblem P ossible Causes Lik ely Solutions
Decreased output. 1. Not enough air pressure and/
or air flow.
2. Obstructed trigger.
3. Incorrect lubrication or
not enough lubrication.
4. Blocked air inlet screen
(if equipped).
5. Air leaking from loose housing.
6. Mechanism contaminated.
1. Check for loose connections and make sure that
air supply is providing enough air flow (CFM)
at required pressure (PSI) to the tool's air inlet.
Do not ex ceed m ax im um air pressure.
2. Clean around trigger to ensure free movement.
3. Lubricate using air tool oil
according to directions.
4. Clean air inlet screen of buildup.
5. Make sure housing is properly assembled and tight.
6. Have qualified technician
clean and lubricate mechanism. Install in-line filter
in air supply as stated in Setup: Air Supply.
Severe air leakage.
(Slight air leakage
is normal,
especially on
older tools.)
1. Cross-threaded housing
components.
2. Loose housing.
3. Damaged valve or housing.
4. Dirty, worn or damaged valve.
1. Check for incorrect alignment and uneven gaps.
If cross-threaded, disassemble and
replace damaged parts before use.
2. Tighten housing assembly.
If housing cannot tighten properly,
internal parts may be misaligned. Technician needs
to disassemble tool, align parts and reassemble.
3. Replace damaged components.
4. Clean or replace valve assembly.
Housing heats
during use.
1. Incorrect lubrication or
not enough lubrication.
2. Worn parts.
1. Lubricate using air tool oil
according to directions.
2. Have qualified technician inspect internal
mechanism and replace parts as needed.
Follow all saf ety precautions w h enev er diag nosing or serv icing th e tool.
Disconnect air supply bef ore serv ice.

Page 14 For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 . Item 61718
SAFETY OP ER ATION MAINTENANCESETU P
P art Description Q ty
1 Housing 1
2 Valve Sleeve 1
3 Reverse Valve 1
4 Trigger 1
5 Spring Pin 1
6 Valve Stem 1
7 Valve Seat 1
8 Steel Ball 1
9 Spring 1
10 Air Inlet - 18 NPT 1
11 Air Regulator 1
12 O-Ring 1
13 Set Screw 1
14 Spring 1
15 Anvil Bushing 1
16 Anvil Collar 1
17 O-Ring 1
18 Standard Anvil 1
19 Hammer Cage 1
20 Hammer Pin 1
21 Hammer Dog 1
P art Description Q ty
22 Drive Cam 1
23 Ball Bearing 2
24 Cylinder 1
25 Rotor 1
26 Rotor Blade 6
27 Front End Plate 1
28 Front Dowel Pin 1
29 Rear End Plate 1
30 Rear Dowel Pin 1
31 Rear Gasket 1
32 Back Cover 1
33 Spring Washer 4
34 Cap Screw 4
35 Stop Pin 1
36 Spring Pin 1
37 Set Screw 1
38 Exhaust Deflector 1
39 Tapping Screw 2
40 Plug 1
41 Nose Rubber 1
42 O-Ring 1
P arts List and Diag ram
P LEASE R EAD THE FOLLOW ING CAR EFU LLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
P arts List
R ecord P roduct' s Serial Num ber Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.

Page 15For tech nical q uestions, please call 1 -8 8 8 -8 6 6 -5 7 9 7 .Item 61718
SAFETYOP ER ATIONMAINTENANCE SETU P
Assem bly Diag ram

Lim ited 9 0 Day W arranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3 4 9 1 Mission Oak s Blv d. • P O Box 6 0 0 9 • Cam arillo, CA 9 3 0 1 1 • 1 -8 8 8 -8 6 6 -5 7 9 7