Centrewire Chiltern MK2 User manual

Installation Guide
Chiltern MK2 Gate In Frame (1 Way or 2 Way)
1003442-01 | v1
Technical Document
Call: [phone] | Email: [e-mail] | Weblink: https://centrewire.com
Product Code(s)
1000875-01 (1 Way)
1000876-01 (2 Way)
1-Way Catch
2-Way Catch

2
INTRODUCTION ............................................................ Page 3
BILL OF MATERIALS ...................................................... Page 4-5
HOW TO ASSEMBLE ..................................................... Page 6-8
RECOMMENDED MAINTENANCE ............................. Page 9
CONTACT ........................................................................ Page 9

3
INTENDED USE
Galvanised steel mesh gate, integral H-frame, easy latch and self closing gate system.
TECHNICAL DATA
Item Number: 1000875-01/1000876-01
Dimensions (W x H): Approx. 1925 x 1955
SAFETY INFORMATION
PLEASE TAKE NOTE OF THE FOLLOWING SAFETY PRECAUTIONS BEFORE USE FOR
THE WELLBEING OF ALL ANIMALS AND PERSONNEL. ANY HARM OR INJURY
WHICH OCCURS FROM THE LACK OF COMPLIANCE WITH THESE HEALTH AND
SAFETY MEASURES WILL BE THE RESPONSIBILITY OF THE OPERATOR.
¨ IMPORTANT! Read these instructions carefully before use and keep them for
future reference.
¨ Situate this product on a level, solid surface.
¨ Personal protection may be required for some stages of installation.
¨ CAUTION! When handling heavy equipment, some stages of installation may
require at least two people.
¨ DO NOT lean on or exert undue pressure on the product.
¨ CAUTION! Check posture when lifting/manoeuvring the equipment or
associated parts.
¨ ALWAYS Check the product for damage before each use.
If you have any questions or comments regarding the product, we will be glad to hear
them, you can do this by contacting our sales team, Call: [phone] or
Email: [email protected].
PRECAUTIONS
¨ NOT SUITABLE FOR USE IN A STRAINED FENCE LINE.
¨ AVOID UNEVEN AND DAMP GROUND.
¨ REMOVE OVERHANGING BRANCHES OR EXPOSED ROOTS.
¨ CONSIDER THE EXISTING FENCE LINE OR BOUNDARY THAT
MAY DIRECTLY IMPACT THE SITING OF THE PRODUCT.

4
PRODUCT BOM 1000875-01 (1 Way)
ALL FEATURES LISTED BELOW ARE FITTED TOGETHER AT THE FACTORY AND
WILL BE SUPPLIED FULLY ASSEMBLED.

5
PRODUCT BOM 1000876-01 (2 Way)
ALL FEATURES LISTED BELOW ARE FITTED TOGETHER AT THE FACTORY AND
WILL BE SUPPLIED FULLY ASSEMBLED.

6
HOW TO ASSEMBLE
STEP 1. EXCAVATION
Dig x2 holes (for posts) and a shallow trench (for cross bar),
depth into ground deep should be enough to allow the cross bar of the H frame to be
150mm-200mm below ground level.
STEP 2. PLACEMENT
CHECK ALIGNMENT OF THE GATE IN FRAME IS LEVEL AND PERPEDICULAR, THE
GATE IN FRAME MUST BE PERFECTLY LEVEL, EVEN IF THE EXISTING ADJADCENT
FENCE LINE IS NOT! installing this product not level could potentially result in failure
to operate the gate.
STEP 3. EMBED
Set the posts and crossbar into ground with rubble and/or concrete.

7
STEP 4. SET HANDLE TO OPERATE MODE
Handle is assembled
down for security in
transportation.
Disassemble handle
to reposition for use.
Ensure the handle is inserted
through the top rail loop and
sliding D loop before fastening.
Handle assembled. ü

8
STEP 5. ADJUST CONTROLLED SPEED HINGE SYSTEM
By adjusting the position
of the top hinge pivot
point the closing speed
of the gate will become
faster or slower.
Untightening the bolts
allows the operator to
move the top hinge
assembly either towards
the hang post, for slower
closing speed, or, away
from hang post for
faster closing speed.
¨ RETIGHTEN BOLTS TO MAINTAIN SET SPEED!
¨ ADJUSTMENT TO BE MADE AFTER THE GATE HAS BEEN INSTALLED!
STEP 6. COMPLETION
Final checks,
¨ CHECK ALL NUTS ARE SECURE.
¨ REMOVE ANY ROUGH PATCHES OF ZINC WITH A FILE OR SANDPAPER.

9
RECOMMENDED MAINTENANCE
REGULAR MAINTENANCE CHECKS TO THE PRODUCT WILL GIVE EARLYING WARNING
OF ANY PROBLEMS, SUCH AS DAMAGE, CORROSION OR MISSING PARTS AND WILL
ENSURE YOUR PRODUCT IS RUNNING SMOOTHLY AND SAFELY.
¨ General inspection of the entire product.
¨ Ensure all moving components are free of debris and are functioning correctly.
¨ Any damage to steelwork (causing exposure of bare metal) should be made good
by rubbing down and applying x1 coat of galvanizing coating and x1 of oil based
paint.
¨ Check all fasteners sets are tight. Ensure all parts are in place before each use.
¨ Remove any obstructions and cut away any vegetation growing on the kit.
¨ Lubricate all moving parts, in particular latches and locking systems
¨ Simply cleaning down after each use will increase the working life due to the highly
corrosive effect of animals urine and/or faeces.
CONTACT
Headquarters
Centrewire Ltd
Mossfield Road
Adderley Green
Stoke-on-Trent
ST3 5BW.
T: [phone]
E: [email protected]
1003442-01 | v1