Cheviot 5138 User manual

Tel : [phone]
www.cheviotproducts.com
CARE AND MAINTENANCE
Minimum Maintenance is required to maintain product finish. With proper
maintenance your CHEVIOT Faucet will continually look like new. Special care
should be taken when cleaning your faucet and the following suggestions should help
extend your faucet life.
a) Cleaning should be done regularly using a soft cotton cloth and warm water, then
towel dry.
b) Do not use cleaners that contain abrasives or harsh chemicals; Care should be
taken in selecting cleaning supplies. Many cleaners contain detergents, ammonia, or
other corrosive solvents that could damage your faucet finish.
c) occasionally clean with a non-abrasive wax polish.
Model # 5138
INSTRUCTIONS
1. Attach the S-Union to the tub with flat
metal washer and 1/2” lock nut. Make
sure that escutcheon is tight against
S-Union arm (hand tighten only).
2. Attach faucet to S-Unions (3/4“ rubber
washers must be installed) and adjust
faucet so that it sits level. Now tighten
hex nuts on back of faucet to secure the
S-Unions. Then tighten the 1/2” lock
nuts on the back of the S-Unions to
secure faucet on vertical surface.
3. Next connect the water supply lines.
Must have hot going to hot side & cold
to the cold side. If using 1/2“ OD
decorative supply line connect the hex
nuts at the top of the supply lines to the
back of the S-Unions. If installing inside
the wall use copper fittings.
4. Once installed, remove aerator to
flush faucet and water
lines.
This will remove any debris that
may be trapped. Then attach aerator.
21
_
2
"
6"
61
_
2
"
15
_
8
"
45
_
8
"
21
_
2
"
37
_
8
"
21
_
4
"

CARE AND MAINTENANCE
Minimum Maintenance is required to maintain product
finish. With proper maintenance your CHEVIOT Faucet
will continually look like new. Special care should be
taken when cleaning your faucet and the following
suggestions should help extend your faucet life.
a) Cleaning should be done regularly using a soft
cotton cloth and warm water, then towel dry.
b) Do not use cleaners that contain abrasives or harsh
chemicals; Care should be taken in selecting cleaning
supplies. Many cleaners contain detergents, ammonia,
or other corrosive solvents that could damage your
faucet finish.
c) occasionally clean with a non-abrasive wax polish.
NOTE
Before drilling holes in
floor, determine the width
of the faucet supply nuts
that you want to attach the
riser tubes to (these will
be for how far apart you
will be drilling holes). Now
determine where your tub
lip will be to make sure
faucet spout is at least 1”
inside of tub lip.
WATER IN
1/2” MALE NPT
1/2” FEMALE NPT CONNECTOR
SUPPLIED
SERVICE STOP ACCESS SLOT
3/4-14 NPSM
31”
26
1
4”
1
_”
4
3 1
_”
4
1
_”
4
3
_”
4
IMPORTANT:
Please make sure supply lines in the floor
are reinforced to prevent movement down,
or there is a possibility of leaks.
Decorative tube
Cover, Flange
1/2” Female NPT Connector
Supplied
Water in 1/2” Male NPT
Floor
Connector retaining flange
INSTRUCTIONS
2. Connect 1/2” Female NPT connector
with 1/2” male pipe protruding from
mounting surface approximately 1/2” -
1”. Capture flange between 1/2” Female
NPT connector and 1/2” male pipe.
3. Connect service stop valve with slottled
operating screw facing the rear of the
installation - Check the slotted operating
screw has remained in position.
4. Slide decorative tube over inner tube
with access slot aligned with stop
valve operating screw.
5. Slide decorative flange over outer tube,
and place on the top of floor mounting
flange.
6. Slide union into decorative tube, install
the faucet, and lock union is position
using the hex key supplied.
1. Install connector retaining flange
over 1/2” male pipe.
IMPORTANT:
Please make sure supply lines in the floor
are reinforced to prevent movement down,
or there is a possibility of leaks.
Model # 3980
Tel :[phone]
www.cheviotproducts.com