Cichewicz Futura Plus Series User manual

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
1
PELLET’S BOILER FUTURA PICUS
Designed and tested in Sweden !

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
2
1. Description of the system
Futura plus is steel water boiler designed for combustion of wood pellet (with installed pellet
burner) and wood/coal (without installed burner) and oil (with installed oil burner of
Herrmann) . Pellet is renewable ,environmentally friendly, very cheap and easy to buy
domestic fuel. The boilers with output of 20 kW can be used for heating of small buildings
such as family houses, lodging-houses, motels, workshops, etc. The boilers with output of 50
and 75 kW suit for heating of buildings up to 700 m2of area like shops, schools, apartment
houses, etc. We can provide also bigger units f.e: up to 200 kW but all dimensions and
features of the system are individually proposed to the customer.
Boiler was tested on different burners from Sweden. Structure of the boiler, design is made
among Swedish project. System of the combustion, boiler was tested in Sweden.
FEATURES:
•Possibility of combustion of pellets and
solid fuels like wood/coal
•Mechanical fuel feeding system
connected with easy-throw system of
pellet to the combustion chamber
•Automatic ignition system;
•Economical operation - 300 L fuel tank
guarantee reloading of the fuel every
5-7 day
•Self diagnostic system Efficiency like in
gas boilers – up to 92 % (pellet)
•Fuel tank in wheels is very easy to
transport
1. steering of pump 2 hopper 3 burner
4 plastic tube 5 motor 6 burner steering

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
3
2. Technical data of FUTURA
Futura pellet boiler contains :
•3 pass boiler made from steel (5/6 mm ) with iron coast plate in combustion chamber
•Outer Jacket with insulation
•Fuel tank on wheels with volume 300 L
•Eurofire pellet burner with screw (feeding system), motorgear
•Blower
•Automatic ignitron system ( pellet)
•Digital boiler/burner control panel with self-diagnostic system
•burn-back protection system
•Overheat safety device
•Ash drawer
Our product is manufactured conforming the ISO Norm 9000:2001 TUV CERT GERMANY, and
fulfill hardest emission norms in Europe.
Tab. 1. Dimensions and technical parameters of boiler.
Parameter SI FUTURA 25 FUTURA 35 FUTURA 60
Weight kg 350 480 580
Water capacity l 60 100 130
Fuel hopper capacity l 160 160 250
Dimensions of the boiler
width x depth x height mm 510 x 810
x 1290
570 x 810
x1290 630 x 810 x 1310
Dimensions of the tank
width x length x height mm 510 x 810
x 1300
510 x 810
x 1300
510 x 810
x 1300
Working water pressure ! bar max. 2,0
Recommended working water
temperature °C 65 – 80
Minimal return water temperature °C 60
Maximum height of heating system
above boiler’s base level. m 25
Maximum safety valve opening
pressure bar 2,0
Noise level dB 52 -60dB (A)
Required chimney draught mba
r 0,1 – 0,2
Connector pipes - heating water Js G 1 1/2”
- return water Js G 1 1/2”
Supply voltage 1 PEN ~ 50 Hz 230 V TN – S

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
4
3. Description of the boiler and burner
3.1. Boiler’s construction.
The main part of the boiler is a heat exchanger consisting of combustion tubes. In the lower
part of the boiler’s body the combustion chamber with primary air pre-mixer and ceramic
catalyst is located. The ceramic catalyst , lowers volatilizing of volatile matter and radiates
heat back to the burner what guarantees perfect combustion of fuel. Combustion of pellet is
provided by installed burner Euro Fire with automatic feeding system. Under the combustion
chamber is located ash drawer.
The fuel hopper is made from steel , whole construction is located on the wheel. It provides
easy transport and easy arrangement of the boiler room, In the lower part of the fuel hopper
feeding screw mechanism is located. Motor and steering are installed in upper part of the
fuel tank.
On the back wall of the boiler’s body the heating and return water connector pipes and
smoke conduit are located. The connector pipes are screwed and theirs size is 1½”.
The steel heat exchanger, its steel cover as well as the combustion chamber and ash box
door are coated with thermal insulation, which guarantees low environment heat loss.
According to EN 303-5 norm, we have to versions of the boiler:
1) with built in water exchanger (spiral) to protect system against pressure and water
overheating
2) without water exchanger , in this version You can install boiler in opened installation
systems

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
5
3.2. Burner ’s description
Door contact breaker
Fan
Igniter connection
Photo resistor
Control cable
Backside fire protection
Feed tube
Gable
Ground cable connection

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
6
3.3. Control and safety devices.
Lamp indicates that unit is connected to power and
that the security circuit is closed.
(overheat thermostats for furnace and feed tube an
d
also furnace door security switch).
Lamp indicating feed screw movements
Lamp indicating connected igniter
Strapping (in fuse box)
Connection of optional external thermostat
Cable to burner
Electricity outlet for feed screw
Transformer
PLC
Cable connection for temperature sensor
Main switch
Power supply, 230V

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
7
4. Location and installation of the boiler in boiler room.
4.1. Norms and regulations.
Due boiler gasses temperature 90-100º C it is obligatory to put the INOX or other material
tubes into the chimney.
The solid fuel boiler must be installed in accordance to current norms and regulations f.e EN
303-5 . Unauthorized changes in boiler’s mechanical or electrical construction will be treated
as a violation of Guarantee Agreement and its consequence is immediate termination of the
guarantee. The fact of installation and first start of the boiler should be signed in Guarantee
Card.
The heating system should be installed according to the following plans:
a) Heating System – during installation and operation of the boiler it is very important to keep
safe distance from the inflammable materials. The boiler is allowed to work only in open
type heating systems!
b) Electrical installation – the boiler’s power supply is 230V/50Hz
c) Chimney – the connection of the boiler to chimney can be done only after agreement
from authorized chimneysweep. It must be done with respect to current norms and
regulations. The chimney should be built form few layers. Due boiler gasses temperature 90-
100 C it is obligatory to put the INOX or other material tubes into the chimney. Required
chimney draught is 0,1 – 0,2 mbar.
d) Following Law regulations should be fulfilled :
98/37/EEG
89/336/EEG
73/23/EEG
EN 55014-1, 1993 /A1, 1997
EN 55014-1
EN 55014-2 C1 1998
EN 61000-3-2
EN 61000-4-2, -3-4-5-6-11, Level2
EN 50165
EN 50165 C1
EN 60335-1
EN 303-5
4.2. Possibilities of boiler’s localization.
Localization of the boiler according to Fire Protection Regulation:

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
8
1. Placing on flammable foundation.
−place the boiler on non-flammable and thermal insulating pad which should protrude not
less than 20 mm outside boiler’s dimensions;
−if the boiler is located in the basement it is required to place it on a base raised not lower
than 50 mm over floor’s level. The boiler and the fuel hopper must stand vertically and can
be leveled using the regulating screw in fuel hopper’s leg.
2. Safe distance from inflammable materials.
−during installation and operation of the boiler the safe distance of 200 mm from
inflammable materials must be kept;
−during installation and operation of the boiler the safe distance of 400 mm from
class C3inflammable materials (paper, cartoon, wood, plastic, etc.) must be
kept;
−unless the material’s inflammability class is known the distance should be
doubled.
Tab. 9. Inflammability classes for building materials.
Inflammability classes for building
materials Materials
A – non-flammable sandstone, concrete, bricks, fire protection plaster, mortar, ceramic tiles, granite
B – inflammable with difficulty wood-cement boards, glassfiber, gullfiber
C1– inflammable with difficulty beech wood, oak wood, plywood
C2– medium inflammable pine wood, larch wood and spruce wood, cork, wood boards, rubber floor covers
C3– easy inflammable asphalt plywood, celluloid mass, polyurethane, polystyrene, polyethylene, plastic, PVC
Localization of the boiler according to required maintenance and service space:
•1 000 mm of free space must be left in front of the boiler.
•Minimal distance between back wall of the boiler and boiler room’s wall is 400 mm.
•Minimum distance between free side of the boiler and boiler room’s wall is 100 mm.
•The (230V/50Hz) electr. socket should be easy to access.
Pic. 3. Localization of the boiler in the boiler room.

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
9
Fuel storage:
•Only dry fuel can provide high efficiency of boiler operation. It is recommended to store
the fuel in the basement or if storing outdoor the fuel must be at least covered with roof.
Boiler room’s ventilation:
Appropriate supply and exhaust ventilation must be provided in the boiler room (the air
consumption for FUTURA 25-75 kW is 50 m3/ h - 225 m3/ h). The supply ventilation outlet’s lower
edge should be placed not higher than 300 mm over floor level and exhaust ventilation inlet
should be placed as high as possible under boiler room’s ceiling.
.
Installation of the burner
Chimney
The chimney can be made up of bricks, steel tube or be an approved prefabricated steel tube chimney. A
draught of 10-20 Pa is sufficient. If the area of the chimney is too big a metal tube can be installed to
decrease the area. If you have doubts regarding your chimney please contact your local chimney-sweeper. Be
aware that tall chimneys and also chimneys with large area necessitate more heat to avoid condensation.
The chimney gas temperature needed is determined by whether condensate is formed
at the top of chimney. As a guideline the temperature must be at least 80°C one
metre down from the top of the chimney.
Strong wind or high chimneys can sometimes cause big variations in chimney
draught. This affects the conditions for a high efficiency in the burner and the
settings that have been made. A draught stabiliser mounted after the furnace helps
level the variations in draught and will also ventilate the chimney.
Furnace
Eurofire pellet burner can me mounted on most furnaces. The minimum recommended fireplace
dimensions are: depth 390mm, height 200mm and width 250mm. When mounting in furnaces with less
space or when using the maximum capacity an extensional sleeve coupling can with advantage be used
between the burner and the furnace. This is to make sure the combustion is not interfered by the flame
hitting the rare wall in the combustion chamber. Sleeve coupling can be bought as extra equipment.
If possible, mounting in combination furnaces should be done in the oil combustion chamber to get the
highest efficiency possible. Due to poor draught, too small combustion chamber or suchlike this may not
work. If that is the case, mount the burner in the chamber made for firewood. If the original furnace door is
used a hole must be made according to the template on page 21. Also drill four 6 mm holes in accordance
with the template for the burner’s lock arms. As an alternative the burner can be screwed on directly to the
door.
Pellet Store
A feed screw supplies the burner with fuel from an external fuel store of some kind. The store can be of
different sizes; from weekly stores to stores big enough to contain the whole annual need. The pellet store

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
10
should be constructed in a way so that the feed screw forms a maximum angle of 45°with the floor plane.
The store must have some kind of a cover to keep rubbish and other things from getting in touch with the
rotating feed screw.
When building big pellet stores for bulk filling, your retailer can assist with drawings and material
suggestions for an optimal result.
Filling of pellet is done by air injection from bulk carrier to a big store or manually from smaller or bigger
bags to a weekly store.
When for the first time starting the burner or if you have run out of fuel, the feed screw between the store
and the burner must be filled with pellet before starting the burner. This is done by covering the inlet of the
feed screw with pellet and then plugging the plug into a power point. Let the screw operate until it is filled
with pellet. Make it a practice to control the pellet quantity in the starting dose when new pellet have been
delivered. This is to guarantee a problem-free operation.
Store the pellet on a dry place to keep the pellet in its original hard consistency. Damp pellet will be soft and
dissolved. Do not use the pellet if it gets damp since this will cause operational disturbance and problem.
Feed Screw
Install the screw-engine on top of the feed screw and pull it firm. After that, place the feed screw in the
intended pellet store. Make sure it does not slope any steeper than 45°. Fill up with pellets enough to cover
the feed screw inlet properly. Connect the screw to a power point and run it until it is completely filled with
pellets. Do not put fingers or other items in the outlet of the rotating feed screw!
Structure
The burner consists of burner housing with detachable gable and channel for the pellet transport up to the
combustion part. Housing, channel and gable are made of lacquered steel plate. The burner housing serves
as a hold for the combustion part and the detachable gable. Also the igniter is attached inside the gable. The
burner housing gable serves as a hold for the combustion fan, the photo resistor and an electronic card with
switchboard panels.
The combustion part consists of a cassette with a top in the shape of a hood. The cassette is pushed into the
burner housing and fastened with two bolts. The combustion part is completely made of heat-resisting
stainless steel. The cassette also serves as a hold for the electric ignition. The cassette system makes the
electric ignition very simple to replace when necessary. The burner consists further of a separate control unit
and a feed screw for the pellet fuel. The security system consists of a backside fire protection, a photo
resistor and a door contact breaker. The backside fire protection consists of a fall shaft and a thermo switch
placed on the feed tube. The thermo switch must be restored manually, if it for some reason has been
triggered.
Connection of Burner with Temperature Sensor (standard)
The burner is delivered with a temperature sensor which function is to control the start and stop of the
burner.
The sensor makes an adjustable difference for start and stop possible (reduces the number of start ups) and
shows the present furnace temperature in the display of the furnace control.
Accumulator Control
In combination with the burners temperature sensor the burner can also be controlled from e.g. an
accumulator tank using a mechanic or electronic thermostat. The thermostat switches off when the recipient
gets warmer than the pre-set temperature and close if the recipient gets colder. The advantage with this
connection can be if you only wish to charge the recipient with heat to a certain level.
Note that the thermostat must be potential free, i.e. stress free!
For the burner to be able to start the furnace temperature must be within the burner control temperature
and the thermostat in the accumulator tank must be closed.

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
11
Connecting up of Burner to Furnace’s Existing Double Thermostat
If it is not possible to use the burner control’s temperature sensor the existing furnace thermostat
(overheating protection and operating thermostat) can be used to control the burner. The start temperature
on the burner is set on the furnace’s operating thermostat.
Note that the thermostats (overheating protection and operating thermostat) must be potential free, i.e.
stress free. Also note that the clamp (fuse) in the fuse holder must be removed for the overheating
protection to function correct.

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
12
Installation Instructions
1. If the enclosed connection sheet is to be used (the burner can sometimes be mounted directly on the
existing door) the size of the sheet is adjusted to the furnace door. Make sure the sheet is big enough to
make room for the holes of the fastening bolts, and that the arms of the two locks are turned upwards
on the sheet.
2. Fasten the sheet in a way that it tightens properly to the furnace. Use exhaust paste or the like that can
stand a minimum of 250°C as tightening between connection sheet and furnace. If connection sheet is
not used the furnace door must be 150 x 150 mm with holes for the lock arms. As an alternative the
burner can be screwed on directly on to the door.
3. Connect the burner to the furnace through the connection sheet. Lock the burner with the lock arms.
4. Connect the PLC to the burner via the connection block equipped cables. The connection blocks are
gently pressed towards the corresponding blocks until located in the correct position. Do not forget the
ground cable! After that, the loose cable fitting is mounted and fastened in its socket on the left side of
the burner.
5. Place the PLC on furnace room wall, pellet store or furnace, make sure that the box and the cable are
not exposed to radiant heat from furnace doors or the like. Fasten the box properly.
6. Connect the PLC to the overheating protection in the furnace (see Electricity Scheme). If the furnace
has an attachment plug for oil burners this can be used for the pellet burner. The burner is then
connected both via the overheating protection and the furnace’s operating thermostat and since the
burner is equipped with a separate temperature control the furnace’s operating thermostat must be put
on maximum to avoid operations disturbance.
Put the burner’s temperature sensor in a thermostat tube in the furnace
Adjustments of Burner
This may only be performed by trained service staff or person with equivalent knowledge.
Settings at Delivery
The control box has pre-set settings from factory but adjustments can be needed due to variations in power
supply and quality in the pellet, required power, chimney draught and feed screw used. These adjustments
should be made by trained retailer or person with equivalent knowledge.
Quality of the Pellet
Insist on an undissolved pellet of hard consistency when purchasing from your supplier. The pellet must be
made of wood with a weight of 650 - 700kg/m3.The power supply in the pellet must be between 4.7 and 5.1
kWh/kg and the proportion of ashes no more than 1 %.
Chimney Draught
Normal draught in the chimney is 10 - 20 Pa. If the negative pressure gets to big a draught stabiliser can be
installed on the chimney.
Photo Resistor
The photo resistor makes indicates that a flame has been established. The sensitivity of the photo resistor
can be adjusted. (see Manual for Control Unit).
Chimney Gas Temperature
The chimney gas temperature varies depending on furnace and the pre-set power settings for the burner.
Too low temperature can result in problems with condensation in the tube. One meter down from the top
of the chimney the temperature of the gas should be at least 80°C. If you get condensation in your chimney
contact your retailer or chimney-sweeper for advice. A too high temperature will result in uneconomical

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
13
operation and risk for damages on the chimney. Consult with your retailer or chimney-sweeper since they
are experts on these questions.
Adjusting the Thermostat
Your burner is equipped with a temperature sensor controlling the burner. It can be set with a minimum
and maximum temperature between which the burner will work (see Manual for Control Unit).
Starting Dose
Loosen the hose from the burner and hold a litre measure below it. Start the burner and wait until the feed
screw has fed the starting dose. For a normal ignition the starting does should be about 0.3 litre Adjust the
quantity using the control unit.
Starting and Stopping the Burner
To stop the burner the switch on the control switch is set on 0 (Off). Avoid stopping the burner before it
has reached the pre-set furnace temperature since the furnace then will not blow the heating surface.

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
14
Air of Combustion / Amount of Fuel
To optimise the burning/combustion it is necessary with a smoke meter. Adjustments of feed screw times,
fan speed and so is done using the burner’s control box (see Manual for the control unit for adjustment of
pre-set settings).
Feed screws can be found in different variants. From a general point of view they should not lean more than
45°, since uneven feeding and varying start dose sizes can arise. Feed screws longer than 3 metres are not
recommended for direct feed to the burner. All feed times are depending on pellet size and quality and also
the gradient of the feed screw.
The control is furnished with a TEST position giving the possibility to adjust to the required power, that is
the amount of pellet, without the burner being in operation. The feed screw will then work for 3 minutes
while it pellet is collected. By weighting the pellet the input power can be read in the table below.
1kg pellet = 4.8kWh energy content
Activating the TEST position:
Undo the temperature sensor, make sure that any extern start signal is in off position.
Simultaneously press A, B, OK.
TEST-position indicates by flashing * in the furthest down to the right in the display. The test position ends
by pressing ESC. After the test the temperature sensor is connected again where after the equipment is
ready to start.
Do not forget to make the control unit dead before the temperature sensor is disconnected and reengaged.
Power Input Amount of Pellet
Gram per 3 Minutes
Approximate Amount of Pellet
Decilitre per 3 Minutes
Power With 80%
Furnace Efficiency
10kW 104 1.6 8kW
12.5kW 130 2 10kW
15kW 156 2.4 12kW
17.5kW 182 2.8 14kW
20kW 208 3.2 16kW
For rough adjustments the colour of the flame can be used as guideline. The colour should be light orange.
A white flame indicates that there is too much air and a dark red a lack of air. Adjust the fan speed on the
burner control box. Every time an adjustment has been done it is important to let the burner operate for a
few minutes before new control and adjustments are done again. Adjustments are necessary every time
pellet of another quality is used.
For optimal adjustments a smoke meter must be used.
Be aware that fluctuations in these values and also in flame height are normal.

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
15
6. User’s manual.
Only authorized person can carry the installation of the boiler and its connection to the
heating system
First start-up of the boiler must be carried out by service, which is authorized by boiler’s
Producer. The installation and service responsibility lies with the company, which installed the
boiler. Any manipulation, repairs or service in any part of the boiler (excl. users setting on
control panel) are allowed only for Authorized Service and are forbidden for boiler’s user.
•It is forbidden to use inflammable liquids for fuel firing up, boiler has automatic
ignition system and it take 3 minutes for start up !
•It is not allowed to overheat of the boiler during operation.
•It is forbidden to put any inflammable materials on boiler or in its environment.
•Any inflammable materials can’t be closer to the boiler than 1500 mm during ash removal. The ash
should be stored in special non-flammable container with cover.
•If the boiler operates with water temperature lower than 60°C, there is a danger of condensation on
boiler’s heat exchanger walls what results in corrosion and shorter boilers life.
•After the heating season is finished the boiler, smoke conduit and chimney must be cleaned. The
boiler room should be kept clean and dry.
•Any manipulations in mechanical or electrical parts of the boiler are forbidden.
Manual for Control Unit
Description
The control unit consists of a control panel with PLC, feeding device and various electronics. The
connection to the furnace and the burner is through cables with instantaneous coupling. An extern
temperature sensor for mounting in the furnace comes with the control unit.
The burner starts and stops automatically according pre-set operation temperatures. Ignition takes place via
hot air. Automatic restart of burner takes place after volt break down. Current status is indicated on the
display. All settings are kept in the PLC’s memory also during a volt break down.
When working with the burner the control unit must be off.
Any reset of the PLC is done by breaking the supply voltage for a short while.
Course of Events at Start and Stop
Feed screw starts and feed pre-set amount of pellet (starting dose)
Electrical ignition activates.
When the photo resistor has detected sufficient light from the burner the pellet feed starts at low power.
After a few minutes the burner passes into high power.
When pre-set stop temperature is reached the pellet feed stops and the burner cleaning of the burner takes
place, where after wait statues is hold until temperature has dropped to start temperature
When a flame is not detected due to shortage of pellet the burner stops and the display alerts.

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
16
If overheating would take place in burner or furnace the control power is disconnected and the burner
stops.
Note that this demands a manual restart.
After for example cleaning of the burner, manual feed of the pellet screw can be done by pressing the ESC
switch.
Handling the PLC
The control unit is equipped with display to show status, alarm and to simplify adjustments.
To adjust the burner for optimal burning a number of parameters can be changed via the control unit.
Its functions are as follows:
When pressing Aor Bthe display lighting is turned on for about 2 minutes. There are a total of 7 different
display slides with varying information and data. Explanations to what is shown can be found on the
following pages.
Default parameters are shown within square brackets.
Move upwards and
increase number
Move downwards and
decrease number
Accept / save changes
Undo changes
Next picture
Previous picture

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
17
Display slide 1
”eurofire 2004, Temp xxxx ” and drift status.
Drift status is shown furthest down and can be of five different kinds.
Vänteläge = Wait State The burner is ready for start
Uppstart = Starting Start sequence has begun.
Min effekt = Minimum Power Burner in low power state
Max effekt = Maximum Power Burner in high power state
Renblasning = Cleaning Cooling / Cleaning in process
Larm = Alarm Burner stopped due to fault (display light flashing)
Display slide 2
"Temperatur, Till, Från"
Till = On Lowest temperature, where the burner to starts [75]
Fran = Off Highest temperature, where the burner stops [85]
Display slide 3
Ljus = Light Shows the photo resistor’s present rate between 0-255
Gräns = Limit Limited acceptable value on the photo resistor [20]
Display slide 4
Start = Start Time of duration at start for feed screw (starting dose) [60]
Dos2 = Dose 2 Extra pellet feed at long at long ignition time [12]
Vänta = Wait Time in low power position after ignition before high
power position is allowed [40]
Display slide 5
"Matn pellets" = Pellet feeding
Min = Minimum Time of duration for feed screw at minimum power [2.5]
Max = Maximum Time of duration for feed screw at maximum power [5.0]
Display slide 6
"Fläktvärden" = Fan status
Tänd = Ignite Fan speed at ignition *(0-255) [215]
Max = Maximum Fan speed at maximum power *(0-255) [230]
* Maximum fan speed is 255
Display slide 7
"INFO“
“Ekosystem AB“
“Ver:2004.1" (given at support inquiry regarding control unit)
Changing a value
Choose wanted display slide using A and B.
To change a value start by choosing wanted line with + and –.
The line chosen will be indicated by a dark flashing field.
Press OK. The chosen value will flash without being highlighted.
Change the value by using +and – and accept and save with OK.
The value is saved when the line once more starts flashing.
By pressing +or –for a few seconds the alteration speed will increase gradually.
An incorrect unsaved input can be undone by using ESC.
Accumulator Control Position
It is possible to control start/stop of burner in combination with an external signal (accumulator
thermostat). For the burner to get the start order in this position the temperature sensor on the furnace
must call for heat and an external plug must be connected to input 1-2.

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
18
The Burner stops when the furnace has reached its temperature or when the eternal plug is disconnected.
Activating/Deactivating of the accumulator control position is done by simultaneously pressing +, -and
OK.
When the accumulator control position is activated the first display slide shows ACK .

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
19
TEST-position
The normal is to use the DRIFT (operating) position when the burner starts and stops automatically after
pre-set operating temperatures. The control is furnished with a TEST position giving the possibility to
adjust to the required power, that is the amount of pellet, without the burner being in operation. The feed
screw will then work for 3 minutes while it pellet is collected. By weighting the pellet the input power can be
read in the table under Air of Combustion / Amount of Fuel.
1kg pellet = 4,8kWh energy content
Activating the TEST position:
Undo the temperature sensor; make sure that any external start signal is in off position.
Simultaneously press A, B, OK.
TEST-position indicates by flashing * in the furthest down to the right in the display. The test position ends
by pressing ESC. After the test the temperature sensor is connected again where after the equipment is
ready to start.
Do not forget to make the control unit dead before the temperature sensor is disconnected and reengaged.
Putting the Control Unit in Operation
Before the control unit is connected all cables must be connected in a satisfactory way.
Ensure the temperature sensor is set up in a thermostat tube in the furnace.
Actuate the operation switch and ensure that the display shows the following slide after a few seconds.
Browse through the display slides using A and Band ensure that the values are reasonable.
If needed pellet can be fed manually using ESC.
Leave hold of the switch when pellet is falling into the burner.
Switch on the operation switch and wait for the furnace to start.
Make sure that the temperature sensor is activated and is showing the furnace temperature *(recalibration
might be needed).
The burner should be ignited after a few minutes. Normal duration of starting period is 3-6 minutes.
Control the flame and make sure that no smoke is coming into the furnace room. If needed, adjust the pre-
set settings for minimum and maximum power and the fan speed during ignition and maximum power.
Note! Before the control unit is started pellet should be fed up to the burner by connecting the feed screw
to a 230VAC socket.
* Calibration of temperature sensor
The temperature sensor is calibrated before delivery, but recalibration can be necessary.

www.cichewicz.com YOUR HEATING OUR RESPONSIBILITY
20
Adjustment is done by carefully turning the small potentiometer located on the temperature transductor
card in the control unit until correct temperature is shown in the display (compare with furnace
temperature).