CNP Brands bebe care SORRENTO LETTO 092240-388 User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
SORRENTO LETTO CHANGE CENTRE MODEL # 092240-388

2
Read all instructions before assembly and use of the change centre. Keep instructions
for future use.
ADULT ASSEMBLY REQUIRED:
DUETO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY,KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
DO NOT LEAVETHE CHILD UNATTENDED ONTHE CHANGE CENTRE.
TO PREVENT FALLS,DO NOT USE CHANGE PAD WITH ATHICKNESS OF MORETHAN 30MM.
WHEN LOCKABLE CASTORS/WHEELS ARE FITTED,THEY SHOULD BE LOCKED
WHENTHE CHANGE CENTRE IS IN USE.
FOLLOWTHE MANUFACTURER’S ASSEMBLY INSTRUCTIONSTO ENSURE THE SAFETY
FEATURES OFTHE CHANGE CENTRE ARE NOT COMPROMISED.
SAFETY PRECAUTIONS
WARNING
All assembly ttings should always be tightened properly and checked regularly.
To prevent falls,do not leave your baby unattended on the change centre.
DISCONTINUE use once child reaches 12 months of age or 11kgs.
DO NOT allow older children to climb or play on the change centre.
DO NOT use accessories other than those supplied and approved by CNP Brands.
Promptly replace worn out or broken parts.
DO NOT over tighten the bolts.
Be aware of the risk of open res and other sources of strong heat, such as electric bar res,gas res etc.in
close vicinity to the change centre.
DO NOT use this change centre if any part is broken,torn or missing.
ENSURE children are clear of any moving parts when adjusting the change centre.
For warranty purposes,keep your sales receipt to provide proof of purchase.
RECOMMENDED CHANGE PAD (SOLD SEPARATELY):
THIS CHANGE CENTRE HAS BEEN MANUFACTURED FOR USE WITH A CHANGE PAD WHICH MEASURES 750MM
LONG X 500MM WIDE X 30MM INTHICKNESS.
We recommend the Childcare Universal Change Pad model #115140BC-003 to use with this change centre.
Place change pad on top of the change centre ready for use.

3
Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction
manual are generic, therefore product fabrics, colour and design may vary from images shown. CNP Brands reserves
the right to alter product specifications without notice as a result of our ongoing policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Sorrento Letto Change Centre
Congratulations on your purchase of the Sorrento Letto Change
Centre.
This product has been designed and developed with safety, comfort
and functionality in mind. Please take the time to read this manual
carefully before using this product and keep it in a safe place for
future reference.
CONGRATULATIONS

4
ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the box against the list
below. If anything is missing, please contact Customer Service.
In Australia, contact CNP Brands on 1300 667 137, in New
Zealand contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box (Unit Components):
Side Panel Right x 1
x 1
x 1
x 1
x 2 x 1
x 1
Side Panel Left
Top Shelf
Bottom Shelf
Lower Plinth Panel Top Rear Panel
Top Front Panel
Recommended use with 115140BC-003 Universal Change Pad - White.

5
Drawer Side Panel
Drawer Front Panel Front Panel
x 2
x 1 x 1
x 1
x 1
x 1
Front Panel Handle
Drawer Base Panel
Drawer Rear Panel
ASSEMBLY CONTENTS
Supplied loose in box continued (Drawer Components):
Assembly Kit:
Wooden Dowel
27mm Screw
(Drawer Assembly)
x 16
x 8
x 2
x 4
40mm Bolt
(Drawer Assembly)
22mm Screw
(Drawer Assembly)

6
ASSEMBLY CONTENTS / ASSEMBLY / OPERATING INSTRUCTIONS
Assembly Kit continued:
65mm Bolt x 4 x 450mm Bolt
x 1 x 1Allen Key Phillips Screwdriver
(Not Included)
To attach Top Front & Rear Panels...
As small parts are involved in assembly, children should be kept clear of the
assembly area.
Dispose of all packaging material immediately after the change centre is
assembled.
Identify all parts and components.
Clear an area on the floor for assembly and place a sheet on the floor to ensure
the change centre is not scratched during assembly.
a.
b.
c.
d.
1
2
Lay the Right Side Panel down on its side.
Insert 2 x Dowels into each end of the Top
Front Panel.
Attach the Top Front Panel by aligning the
dowels with the dowel holes with the shelf
groove facing inwards.
Push together and secure with one 65mm
bolt.
When attaching the Top Rear Panel, please ensure
that the shelf groove sits above the screw hole.
1a.
1b.
1c.
1d.
2a.
PLEASE NOTE! Make sure that the grooves in both above panels all face
inwards to allow for the tting of the top shelf.

7
ASSEMBLY / OPERATING INSTRUCTIONS
To attach Top Front & Rear Panels continued...
3Insert 2 x Dowels into each end of the Rear
Panel.
Attach the Top Rear Panel by aligning the
dowels with the dowel holes.
Push together and secure with one 65mm
bolt.
3a.
3b.
3c.
To attach Lower Plinth Panels...
1
2
Insert 2 x Dowels into each end of the Plinth
Panel.
With the change centre still lying on its side
attach a Lower Plinth Panel by aligning the
dowels with the dowel holes.
Push together and secure with one 50mm
bolt.
Repeat for the opposite side.
1a.
1b.
1c.
2a.
DO NOT OVERTIGHTEN BOLTS.OVERTIGHTENING BOLTS CAN CAUSE PANELSTO CRACK.
WARNING
PLEASE NOTE! Make sure that the grooves in both above plinth panels
all face inwards to allow for the tting of the bottom shelf.

8
ASSEMBLY / OPERATING INSTRUCTIONS
To attach Top Shelf...
1
2
Carefully lay the Right Side Panel on its back.
Insert the thicker Top Shelf into the grooves
and slide it down until it sits in the groove in
the Right Side Panel.
1a.
2a.
3
1
The Top Shelf should now resemble the image
opposite.
Insert the Bottom Shelf into the grooves and
slide it down until it sits in the groove in the
Right Side Panel.
3a.
1a.
To attach Top Shelf continued...
To attach Bottom Shelf...

9
ASSEMBLY / OPERATING INSTRUCTIONS
2
1
Secure with 2 x 50mm bolts through the plinth
and 2 x 65mm bolts for the front and rear
panels.
Carefully attach the remaining Left Side Panel
onto the upper panels and Lower Plinth Panels
by aligning the dowels and guiding the Top
and Bottom Shelves into the grooves.
2a.
1a.
To attach Left Side Panel...
WARNING! Do not over-tighten bolts.
To assemble Drawer...
1
2
Stand change centre upright.
Pull both of the drawer runners out as far as they
can go.
1a.
2a.

10
ASSEMBLY / OPERATING INSTRUCTIONS
5
3
4
7
6
Place the Front Drawer Panel between the
Side Panels making sure the Base Panel is in
the groove.
Secure with 4 x 27mm Screws.
Connect the Drawer Runner Panels to Rear
Panel using 4 x 27mm Screws.
Make sure that the grooves line up with the
groove on the rear panel.
Slide the Drawer Base Panel into the grooves
and into the Rear Panel groove.
Using 2 x 40mm Bolts, secure the handle to the
Front Drawer Panel.
Place the Front Panel on the Front Drawer
Panel.
Secure with 4 x 22mm Screws.
5a.
5b.
3a.
3b.
4a.
7a.
6a.
6b.
To assemble Drawer continued...

11
ASSEMBLY / OPERATING INSTRUCTIONS
9
8
10
Insert the Drawer by lining up the drawer runners
with the cabinet runners.
Drawer is ready to assemble into main change
centre unit.
Gently push the Drawer closed to engage the
mechanism.
Check all bolts are firm.
9a.
8a.
10a.
10b.
The change centre is now ready for use.
WARNING! Do not over-tighten bolts.
DO NOT OVERTIGHTEN BOLTS.OVERTIGHTENING BOLTS CAN CAUSE PANELSTO CRACK.
WARNING
To assemble Drawer continued...

12
HOW TO CARE FOR YOUR BEBE CARE CHANGE CENTRE
Cleaning
Maintenance
This product has been designed and developed with safety, comfort and
functionality in mind. Please take the time to read this manual carefully before
using this product and keep it in a safe place for future reference.
To ensure the long-lasting use of your change centre, wipe down with a
damp cloth and use a mild soap solution if necessary. Do not use abrasive
cleaners. Always store product in a clean dry place.
Always check parts regularly for tightness of screws, nuts and other fasteners
– tighten or replace if required. To maintain the safety of your change centre,
seek prompt repairs for bent, torn, worn or broken parts. Use only those parts
and accessories approved by CNP Brands.
If you have any difficulties in assembling the change centre, please contact
our Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact
Wainhouse Distribution on 0800 567 5000.

13
ABOUT US
About CNP Brands
Currently, CNP Brands boasts one of the most diverse brand portfolios with
a combination of company owned brands and distribution agreements.
These include distribution lines for Brica, Cybex, Evenflo, Good Baby, Lascal,
Maclaren, Munchkin, Project Nursery, Summer Infant and Yookidoo.
Our own brands, including Childcare, have gone from strength to strength in
recent years. Childcare, and our premium brand bebe care, demonstrate our
commitment to quality and continuing investment in product development.

14
Distributed in Australia by CNP Brands
20 Calarco Drive,
Derrimut,VIC, 3030
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: [e-mail]
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes,Auckland, New Zealand
Customer Service: 0800 567 5000
E: [e-mail]