comptree WF212510AAA User manual

Slide and Swing Set
User’s Manual
PLEASE DO NOT RETURN PRODUCT TO THE STORE
If you have any problem or concerns, please feel free to contact our
customer service department. We will reply you as soon as possible.
E-Mail: [e-mail]
Tel: [phone] Ext.100
WF212510AAA

WARNINGS
ADULT ASSEMBLY REQUIRED
CHOKING HAZARD - Small Parts
For children 18 months and up.
Please read these warnings and the information in this manual in its entirety.
Failure to comply with the following instructions may increase the risk of serious injury and/or death:
• This unit must be assembled and
disassembled by ADULTS ONLY.
• This Slide is suitable for use by most
children 1 to 8 years of age.
• Never use this product in any manner other
than its intended use.
• DO NOT exceed the maximum weight limit
of 110lbs (50kgs) regardless of age.
• DO NOT install this equipment over concrete,
asphalt, or any other hard or rough surface.
The Slide should always be installed over an
appropriate, stable surface (rubber mat, grass,
etc).
• Carpeting and thin mats are generally not
adequate protective surfacing. Ground
level equipment—such as a sandbox,
activity wall, playhouse or other equipment
that has no elevated play surface—does
not need any protective surfacing.
• ALWAYS locate this equipment on a stable,
level surface AT LEAST 7 feet away from
any structure, obstruction, or possible
hazard(s) such as walls, pools, power lines,
verhangs, other playground equipment,
driveways, hard surfaces and/or roadways.
• Children must be supervised at all times
when using this equipment. DO NOT leave
children unattended at any time. This Slide is
NOT for adult or adolescent use.
• DO NOT attach items to the Slide not
specifically designed for this purpose.
Especially in the case of jump ropes, chains,
clotheslines, pet leashes and cables. These
may cause a strangulation or physical hazard.
• This Slide is only designed for family
residential use. NOT intended for commercial
applications and/or use in public areas such
as schools, parks, nurseries, day schools, day
cares, etc. DO NOT allow more than one child
on the Wavy Slide and Ladder at a time.
• Instruct children to always be sure that
the chute opening at the bottom is clear
of any persons, pets or obstructions
before sliding.
• DO NOT allow children to wear glasses
or helmets when using the slide.
• At the time of disposal, this item must be
completely disassembled and separated into
its component types (plastics) for recycling or
pick-up according to local ordinances for
sanitation pickup.
• DO NOT allow children to wear loose fitting
clothing, clothing with straps/loops, backpacks
or wear and/or hold accessories with straps or
loops, or any article of clothing or accessory
with sharp edges which may present a hazard
or become snagged or caught on the Slide
during use. Serious injury and/or accidental
strangulation may occur.
• DO NOT place objects on or under the slide,
or allow people and pets to stand or sit on,
near or under the Slide and Ladder when in
use.
• DO NOT allow children to stand on the slide,
attempt to walk up the slide – this can cause
serious injury. Children must ALWAYS remain
securely seated, in the forward facing position
when sliding. Do not lay down, slide from a
standing position, or slide down the chute
back-wards. DO NOT allow children to stand
on the slide top.
• DO NOT use in adverse weather conditions,
while the seats are wet, or in poorly lit
conditions.
• It is recommended that children wear long
pants when using this slide to prevent friction
of skin against the chute. At the end of the
play season or when the temperature drops
below 40 degrees F, this unit must be stored
indoors, or disassembled and stored inside.
• Please read and refer to other warnings and
use information in the Slide instructions before
use.
• Before each use of this product and twice per
month, inspect and re-place any worn, loose,
defective or missing parts and/or bolts. It is
important to check the entire Slide to ensure
the Chute is in good condition. If any loose,
cracked, missing, or other damaged
components are found, cease use of this item
immediately. If removed for winter storage,
reinstall any plastic parts before allowing use.
• Owners shall be responsible for maintaining
the legibility of the warning labels.

1
PARTS LIST
（NOTE: You will get a basketball, a football, two golf balls and a golf club for free）
Down Side Panel(Right Side)
Down Side Panel(Left Side)
Steps *4
SWING PARTS LIST
Slide(Down Part) *1
Upper Side Panel(Right Side)
Upper Side Panel(Left Side)
Swing and Slide Side Board*3
SLIDE PARTS LIST
Swing Seat*1
Swing Armrest*1
Swing Base*2
Swing Board*2
Stick*1
Slide(Upper Part) *1

2
ACCESSORIES LIST
BASKETBALL STAND PARTS LIST
Dinosaur Board*1
Side Panel*2
Back Board*1
Football Gate*1
Football Net*1
Basketball Hoop*1
Basketball Net*1
Hex Wrench
Wrench
Pole*1
十Shaped Nut
*20
Square Screw
*2
Flower Nut
*18
Connector*1
Round Screw*5
(for basketball stand)
Long Screw*2
(for swing base)
Stopper*2
Stopper*2
Screw*1
(for football net)
Short Screw*2
Net Hook*15
Clip*4

3
ASSEMBLY INSTRUCTIONS
STEP4.
Attach steps F*4 to one board E with nuts c*4.
Attach the slide to board E and tighten them with
nut c*1
STEP3.
Install panel D on slide B with ”十” shaped nuts
a*6. Then, insert screws b*2 through the
panel C and panel D, and tighten with nuts
a*2 from outside.
STEP1.
Install panel C on slide A with ”十” shaped
nuts a*6, and tighten them with wrench.
STEP2.
Put slide B and A together and align the holes,
tighten long screws g*2 with the hex wrench.

4
STEP7.
Attach armrest H to seat G with screw i.
Then attach board J to seat G with screws
e*4.
STEP6.
Tips: You can fill swing base with water or
sand for better stability. Plug the holes with
part h after that.
STEP8.
Attach swing base to board E with nuts c*2.
Insert stick K through board E and tighten
with screw c.
STEP5.
Attach steps and slide to another board E and
tighten them with nuts c*5.

5
STEP11.
Attach pole S to football gate O, and
tighten short screws j*2 with the hex
wrench.
STEP10.
Attach back board N to panel M with “十”
shaped nuts a*2.
Tips: You can fill the panel M with water
or sand for better stability. Plug the holes
with part f after that.
STEP9.
Remove the non-slip accessory on
stick K, and choose a height you want
and insert the stick through the holes
on swing board.
Put the non-slip accessory back and
attach swing base and the stick to
another board E with nuts c*3.
Then, insert clips I*4 into the holes on
stick to hold the swing.

6
STEP15.
Attach panel M to swing board E with
connector d and nuts c*2.
STEP14.
Attach net P to panel M with net hooks
k*15.
STEP13.
Attach net R to hoop Q and connect Q
to board L, and insert into pole S, then
tighten with screw e.
STEP12.
Attach gate O to panel M, and tighten
nuts a*4 with wrench.

7
STEP16.
FINISHED