Craftex CX119 User manual

CX119
14” WOOD BAND SAW
USER MANUAL
Version 0.1

2
TABLE OF CONTENTS
General Safety Instructions------------------------------------------------------------------- 3
Specific Safety Instructions------------------------------------------------------------------- 4
Features------------------------------------------------------------------------------------------- 5
Physical Features------------------------------------------------------------------------------- 6
Setup----------------------------------------------------------------------------------------------- 7
Un-Packing --------------------------------------------------------------------------------------- 7
Proper Grounding--------------------------------------------------------------------------------8
Assembly and Adjustments--------------------------------------------------------------- 9
Blade Tracking ---------------------------------------------------------------------------------- 11
Basic Controls ----------------------------------------------------------------------------------- 12
Test Run ------------------------------------------------------------------------------------------ 12
Blade Tension ----------------------------------------------------------------------------------- 13
Adjusting the Blade Tension ----------------------------------------------------------------- 13
Support Bearings Adjustment---------------------------------------------------------------- 13
Table Stop Adjustment ------------------------------------------------------------------------ 14
Table Tilt Scale Calibration------------------------------------------------------------------- 15
Table Alignment--------------------------------------------------------------------------------- 15
Guide Post---------------------------------------------------------------------------------------- 16
Speed Change Settings----------------------------------------------------------------------- 16
Work-Piece Inspection------------------------------------------------------------------------- 17
Cast Iron Wheels-------------------------------------------------------------------------------- 18
Coplanar Adjustment--------------------------------------------------------------------------- 18
Operations--------------------------------------------------------------------------------------- 19
Ripping -------------------------------------------------------------------------------------------- 19
Cross Cutting ------------------------------------------------------------------------------------ 19
Re-Sawing---------------------------------------------------------------------------------------- 19
Cutting Curves----------------------------------------------------------------------------------- 19
Connecting to a Dust Collector-------------------------------------------------------------- 20
Maintenance ------------------------------------------------------------------------------------ 21
Replacing the Blade---------------------------------------------------------------------------- 21
Replacing the Blade Guides ----------------------------------------------------------------- 21
Tilting the Table Backwards------------------------------------------------------------------ 22
Table and Base---------------------------------------------------------------------------------- 22
Blade & Table Alignments-------------------------------------------------------------------- 22
V-Belts--------------------------------------------------------------------------------------------- 22
Replacing the V-belts-------------------------------------------------------------------------- 23
Parts Breakdown and List ------------------------------------------------------------------24-28
Warranty ------------------------------------------------------------------------------------------ 29

3
GENERAL SAFETY INSTRUCTIONS
Extreme caution should be used when operating all power tools. Know your power
tool, be familiar with its operation, read through the owner’s manual and practice
safe usage procedures at all times.
ALWAYS read and understand the
user manual before operating the
machine.
CONNECT your machine ONLY to the
matched and specific power source.
ALWAYS wear safety glasses
respirators, hearing protection and
safety shoes, when operating your
machine.
DO NOT wear loose clothing or
jewelry when operating your machine.
A SAFE ENVIRONMENT is
important. Keep the area free of dust,
dirt and other debris in the immediate
vicinity of your machine.
BE ALERT! DO NOT use prescription
or other drugs that may affect your
ability or judgment to safely use your
machine.
DISCONNECT the power source when
changing blade and / or making
adjustments.
NEVER leave a tool unattended while
it is in operation.
NEVER reach over the table when the
tool is in operation.
ALWAYS keep blades, knives and bits
sharpened and properly aligned.
ALL OPERATIONS MUST BE
performed with the guards in place to
ensure safety.
ALWAYS use push sticks and feather
boards to safely feed your work
through the machine.
ALWAYS make sure that any tools
used for adjustments are removed
before operating the machine.

4
CX119 is designed to cut wood only. Do
not attempt to use cut metals using this
band saw.
ALWAYS INSPECT the blade for any
cracked or missing teeth before
operating the band saw.
ALWAYS ENSURE that the blade
tension is properly set for the type and
width of blade installed.
NEVER place your fingers or hands in
the line of cut. If you slip, your hands or
fingers may come into contact with the
blade. Always use a push stick when
ripping narrow pieces.
DO NOT back the work-piece away from
the blade while cutting. Always turn off
the machine if you are backing out a cut.
ALL GAURDS must be in place while
operating the band saw to ensure
safety.
ALWAYS FEED the stock smoothly. Do
not force or twist the work-piece while
cutting.
ALWAYS ENSURE that the band saw
blade guard is no more than 1/2” above
the stock.
MAKE SURE before making any
adjustments, the switch is in the “OFF”
position and the cord is un-plugged from
the power source.
NEVER LEAVE the band saw
unattended while it is running.
DO NOT attempt to remove jammed
pieces unless the band saw has come
to a complete stop and the power switch
has been turned to the OFF position.
NEVER TURN ON the band saw if the
blade is in contact with your stock.
ALWAYS ENSURE that the guide
blocks are properly set to prevent blade
wander.
ALWAYS MAKE CERTAIN that the
bearings are properly adjusted to guide
the blade.
MAINTAIN AND SERVICE your band
saw regularly as instructed in the user
manual.
MAKE SURE you have read and
understood all the safety instructions in
the manual and you are familiar with
your band saw, before operating the
CX119. If you fail to do so, serious injury
could occur.
SPECIFIC SAFETY INSTRUCTIONS
WARNING!
The safety instructions given above can not be complete because the environment in
every shop is different. Always consider safety first as it applies to your individual
working conditions.

5
MODEL CX119 – 14” WOOD BAND SAW
As part of the growing line of Craftex woodworking equipment, we are proud to offer the CX119, a 14”
Wood Band Saw. By following the instructions and procedures laid out in this user manual, you will
receive years of excellent service and satisfaction. The CX119 is a professional tool and like all power
tools, proper care and safety procedures should be adhered to.
Motor.......................................................2HP, 110V / 220V (pre-wired), TEFC, Single Phase
Amps.......................................................12.8 Amp / 6.2 Amps
Blade Speed ...........................................1430, 2300, 3250 FPM
Table Size...............................................16” x 20” Precision Cast Iron
Table Tilt .................................................-10° Left and 45° Right
Wheel Size..............................................14”
Maximum Blade Width............................3/4”
Minimum Blade Width.............................1/8”
Floor to Table Height ..............................38”
Cutting Capacity/Throat ..........................13-5/8”
Maximum Width of Cut............................13-5/8”
Maximum Depth of Cut ...........................13”, Ideal for Ripping
Dust Collection Ports ..............................2 Ports @ 4”
Base Dimensions....................................15”x 25”
Blade Length ..........................................114”
Blade Width.............................................3/4"
Bearings..................................................Sealed and Permanently Lubricated
Computer Balanced Cast Iron Wheels....Yes
Powder Coated Paint..............................Yes
Overall Size.............................................39” x 32” x 76”
Approximate Weight................................138 Kgs (307 lbs)
Warranty .................................................3 Years
FEATURES

6
PHYSICAL FEATURES
Blade Tension
Adjustment Handle
Upper Cabinet
Lock Knob
Blade Guard
Adjustment
Hand Wheel
Blade
Guard Lock
Blade
Guard
Miter
Gauge
Fence Rail
Lower Cabinet
Lock Knob
Base
Table
Fence
Magnetic Safety
Switch
Powder Coated
Paint
Fence Lock
Handle
Dust Ports

7
SETUP
Before setting up your machine you need to
read and understand this user manual
completely.
The unpainted surfaces of this band saw
are coated with a rust preventive waxy oil
and you will want to remove this before you
begin assembly. Use a solvent cleaner that
will not damage painted surfaces.
UNPACKING
The machine is properly packaged in a
carton for safe transportation. When
unpacking, carefully inspect the crate and
ensure that nothing has been damaged
during transit. Open the crate and check
that the machine is in good condition.
The hardware (screws, washers & etc)
might be shipped in a plastic bag. After the
machine has been un-packed, check that
all loose parts and hardware are present.
LIST OF CONTENTS
A. Table................................................. 1
B. Table Insert....................................... 1
C. Table Lock Knobs............................. 2
D. Table Tilt Lock Knob......................... 1
E. Table Pin........................................... 1
F. Miter Gauge Holder........................... 1
G. Fence Holder .................................... 1
H. Miter Gauge...................................... 1
I. Fence Assembly ............................... 1
J. Fence Rail......................................... 1
K. Allen Keys......................................... 2
L. Wrench ............................................. 1
M. Hardware.........................................Bag
WARNING!
CX119 is a heavy machine. Do not over-
exert yourself. Use a fork truck or get the
help of an assistant or a friend.

8
PROPER GROUNDING
Grounding provides a path of least
resistance for electric current to reduce the
risk of electric shock.
CX119 is for use on a normal 220V volt
circuit. Make sure that the machine is
connected to an outlet having the same
configuration as the plug. If an adaptor plug
is used, it must be attached to the metal
screw of the receptacle. To prevent
electrical hazards, have a qualified
electrician ensure that the line is properly
wired.
The band saw should be wired with a plug
having 3 prongs to fit a 3 prong grounded
receptacle as shown in figure-1. Do not
remove the grounding prong to fit it into a 2
pronged outlet.
Figure-1 220 volt outlet for CX119
It is strongly recommended not to use
extension cords with your CX119. Always
try to position your machine close to the
power source so that you do not need to
use extension cords.
If it is necessary to use an extension cord,
make sure the extension cord does not
exceed 50-feet in length and the cord is 14-
gauge to prevent motor damage.
WARNING!
Improper connection of the equipment-
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician if you are in doubt as to
whether the outlet is properly grounded.

9
ASSEMBLY
Follow the steps below to assemble your
band saw:
Take the band saw table and put it upside
down on floor and make sure that all the
table bolts shown in the figure are tight.
See figure-2.
Figure-2 Table trunion bolts
Now turn the table up right, and remove the
table pin from the table slot and the table
insert (if already installed) and move the
table in position around the blade guiding
through the table slot. See figure-3.
Figure-3 Assembling the fence
Position the table on the base in such a
way that the bolts under the table extend
through the holes on the base. Thread the
two knobs on the bolts (do not tighten). See
figure-4.
Figure-4 Knobs threaded on the bolts
Position the table on the table stop and the
base so that the table is perpendicular to
the blade. See page 15 for details.
Figure-5 Table sitting on the table stop
Locate the table tilt bracket under the table
and attach it to the band saw using the
bigger lock knob provided. See figure-6.

10
Figure-6 Attaching the table tilt bracket
Once the table is in the correct position,
tighten the table lock knobs under the table
and the tilt lock knob.
Install the table insert at the center of the
table and the table pin into the table slot as
shown in figure-7.
Figure-7 Installing table insert and table pin
Take the fence rail and attach it to the table
using cap screws provided. See figure-8.
Figure-8 Fence rail installed
Now take the fence and pull its handle up
(in the unlocked position). Place the fence
on the fence rail and slide it towards the
blade.
Figure-9 Installing the fence
Attach the miter gauge holder and the fence
holder to the back of the saw using screws
and washers provided see figure-10.
Figure-10 Miter gauge holder and fence
holder installed