Cube Controls GT-X eSports User manual

1
User Guide
GT-X eSports Racing Wheel

2
Due to continuous improvement, the actual product may differ
from the manual.
This manual is for reference only.
For info or support contact us at
[email protected]
or visit us at
www.cubecontrols.com

3
SAFETY NOTICE
Please read the Manual carefully before you use the racing wheel.
Please do not open the racing wheel, otherwise the supplier will not afford
warranty service.
This product does not have waterproof function, please keep it away from
rain, moisture and other items containing liquid such as vape, cup and so
forth.
This wheel is designed for simulation use only.
Disconnect the USB cable from both sides if you will not use this product
for a long time.
Should you find any problems in your wheel, please contact us at
[email protected], do not repair it by yourself.

4
INTERFACE INTRODUCTION
DOWNSHIFT: 2 UPSHIFT: 1
37
38
39
40
3
16
17
26
LEFT CLUTCH ADJ
4 WAY POV SWITCH
PUSH: 29
5
4
33
34
36
35
CLUTCH PADDLE LEFT CLUTCH PADDLE RIGHT
25
21
22
23
43
44
42
41
18
6 7

5
Operating the launch control system:
The maximum value of the left clutch paddle can be adjusted with the
respective thumb knob. Therefore, if the clutch knob is set in the middle of
its travel, when fully depressing the left clutch paddle, its value will go from
the minimum to the value set by the clutch knob, which is middle in this
example. The right paddle always works in a range from min to max travel,
no matter how the clutch knob is set. This system allows the user to mimic
the launch control system used in F1 cars until 2015, where it was possible to
set the clutch bite point.
Finding the correct clutch knob setting:
In a practice session, set the clutch knob at around 50% of its travel, fully
depress both clutch paddles, engage first gear, reach the optimal engine
RPM, release the right clutch paddle. As the car starts gaining speed,
release the left clutch paddle and shift gears as normal. If you notice that
the clutch starts slipping too much, you will need to decrease the left clutch
paddle max value by turning downwards the clutch knob. If you notice that
the engine drops quickly in RPM, then you will need to increase the clutch
slippage by turning the clutch knob downwards.
This value is typically different for each car.

6
USB CONNECTION
Connect the steering wheel by only using the provided cable.
Please note that the wheel connector it’s keyed as the picture below, so it
fits only one way.
Once the plug it’s correctly seated into the body receptacle, secure it by
turning the retaining ring as bottom right picture.
IMPORTANT: do not over-tighten the ring. Just screw it completely until
it stops rotating, do not apply excessive force.
Alignment key

7
CONNECTING THE WHEEL
Each GT-X steering wheel is provided with a dedicated Y style splitter USB
extension cord.
User must use this cable to connect the GT-X wheel to your pc, otherwise if
plugged directly to a standard front/back panel USB port it might not work
as expected due to the port not being able to supply enough power.
Just plug the two USB-A plugs into your PC, preferably the back panel ones,
and connect the coiled cable to the USB-A female connector.
Please avoid any additional extension cords, supplied coiled cable must
connect directly to the supplied USB splitter.

8
BEFORE FIRST USE
The Formula CSX steering wheel needs the Ultimate Game Tech (UGT)
software to display data streamed from the simulator. It’s also a needed tool
useful to customize and configure various options.
It can be downloaded from ultimategametech.com
On the same website, there is a quick introduction on the Layout Generator,
and a useful general guide on the UGT software.

9
Adjusting shift paddles activation point
Introduction:
Although all the racing wheels are already tested and should work correctly
straight out the box, you might need to adjust the shifter sensor activation
point for a correct use on your setup. If the paddles are already set
correctly, you may skip these steps.
This is a pretty simple
procedure and no
additional tools are
needed
Wait for the software to
correctly recognize the
wheel, then it should
load up as the picture
on the right.
Please note that FW
and SW version might
differ from yours.
Click on “Input devices”
on top, and then “Cube
Controls GT-X”.
A new window with all
the available buttons
and sliders.

10
On the left side of the new window
as highlighted in the next screen-
shot there is the setting you need to
adjust, “Digital Switch Point”.
Usually the ideal value is 50, and all
GT-X steering wheels are factory
programmed with such a value.
If for some reason you are
experiencing the shifter button not
being recognized properly you must
lower the value.
Alternatively if the shifter button
is detected as always pressed, you
must increase the value.
It’s best to do this increasing/
decreasing at around 5 steps at a
time and then test if the shifter is
working correctly.
Once the correct value has been
found, hit “Save Settings” at the
bottom of the window.