Diamond Digital DiamondDigital DV322 User manual

DV322
Wide Screen LCD Flat
Panel Display
32” (81.3 cm) LCD Panel Size
User Manual

1
ENGLISH
USER MANUAL
Thank you for purchasing the LCD TV.
Before using your TV, please read the "SAFETY INSTRUCTIONS"
and this "USER MANUAL" carefully to learn how to operate the
TV properly. Keep this manual in a safe place. You will find it useful
in the future.
Notes on lnstallation
This product is marketed with the assumption that it is to be
installed by qualified personnel with relevant skills and competence.
It is recommended to consult with an installation specialist or your
dealer install and set up the product. We cannot assume liabilities
for damages caused by improper installation or mounting, misuse,
modifications or natural disasters.

2
IMPORTANT SAFETY INSTRUCTIONS
SAFETY POINTS THAT YOU SHOULD KNOW ABOUT YOUR LCD TV
Our reputation has been built on the quality, performance, and ease of service of LCD TV.
Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which
will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your LCD TV.
Follow all warnings and instructions marked on this TV.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to
persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle, is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING:
TO AVOID FIRE OR ELECTROCUTION, DO NOT EXPOSE THIS MONITOR TO RAIN OR MOISTURE.
THE MONITOR SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND OBJECTS SUCH AS VASES
FILLED WITH LIQUIDS, SHOULD NOT BE PLACED ON THE TV.
NOTE: There are no user serviceable parts inside the TV.
Model information and serial numbers are indicated on the rear side of the TV.
CAUTION: Adjust only those controls that are covered in these instructions, as improper changes or modifications not expressly
approved by us could void the user's authority to operate the TV.
MODIFICATIONS: The FCC requires that the user be notified that any changes or modifications made to this device, that are not expressly
approved by us may void the user's authority to operate the equipment.
POWER SOURCE
THIS TV IS DESIGNED TO OPERATE ON 120 VOLT 60Hz, AC CURRENT. INSERT THE POWER CORD INTO A 120 VOLT 60Hz
OUTLET.
TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TV (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR
OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED. THIS IS TO PREVENT BLADE
EXPOSURE. NEVER CONNECT THE TV TO DIRECT CURRENT OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE.
CAUTION: Never remove the back cover of the TV as this can expose you to very high voltages and other hazards. If the TV
does not operate properly, unplug the TV and call your authorized dealer or service center.

3
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
Read before operating the appliance
Follow all warnings and instructions marked on this TV.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding- type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles, and at the point where they exit from
the apparatus.
11. Only use the attachments/accessories specified by the manufacturer.
18. The Shock Hazard Marking and Associated Graphical Symbol is
provided on the bottom panel of the unit.
19. This apparatus is designed to comply with the recommended safety
standards for tilt and stability.
Do not pull the cabinet with excessive force. Doing so can cause the
product to overturn, resulting in damage to the product and/or
personal injury.
20. Follow instructions for wall, shelf, or ceiling mounting as
recommended by the manufacturer.
21. An outdoor antenna should not be located in the vicinity of overhead
power lines or other electrical circuits.
22. If an outdoor antenna is connected to the receiver, ensure that the
antenna is grounded to provide some protection against voltage
surges and built up static charges. Section 810 of the National
Electric Code, ANSI/NFPA No. 70-1984, provides information with
respect to proper grounding for the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of
grounding connectors, location of antenna-discharge unit,
connection to grounding electrodes and requirements for the
grounding electrode.
12
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/appliance combination to avoid injury
from tip-over.
NEC NATIONAL ELECTRICAL CODE
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the appliance has been damaged in any way, such as when a
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Warning-To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
16. Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, shall not be placed on the apparatus.
17. The apparatus is entertainment use only and visual display takes are
excluded.
Note to the CATV system installer: This reminder is intended to point the
CATV system installer to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the
cable’s ground wire shall be connected to the grounding system of the
building, as close to the point of cable entry as possible.
Do not place any objects on top of the TV. They may fall or cause
a child to climb up to retrieve the objects.
Disposal of this product may require specific instructions
pertaining to your resident state. For disposal or recycling
information, please contact your local authorities or the
Electronic Industries Alliance: www.eiae.org.
CAUTION
:
PREVENTION OF SCREEN BURN IN
Continuous on-screen displays such as video games, stock market quotations, computer generated graphics and
other fixed (non-moving) patterns can cause permanent damage to the TV. Such “SCREEN BURN IN” constitute
misuse and are NOT COVERED by our Factory Warranty.
PUBLIC VIEWING OF COPYRIGHTED MATERIAL
Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior
authorization from the broadcaster or owner of the video program material.
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(
NEC SECTION 810-20
)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUNDING CONDUCTORS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250 PART H)
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT

4
Important
Please read this User's Manual thoroughly, especially the Important Safety
Instructions on Pages 2 to 3 and 6 to 10. Misuse may cause damage to your
LCD TV and could shorten its lifespan, or may even cause injury to yourself.
Should you encounter any difficulty in the set-up or operation of your TV,
refer to the Troubleshooting guide at the back of this manual.
In the unlikely event that there is a problem with your LCD TV, switch off the
power and unplug the TV, and contact your dealer immediately.
CAUTION
Under no circumstances should you remove the back cover of your LCD TV.
Never guess or take any chances with electrical equipment of any kind - it is
better to be safe than sorry!
Software Notice
It is prohibited for the end user of this product to copy, reverse engineer or
reverse compile the software included therein, to the extent permitted by law.
LCD TV
After the LCD TV has been on for any length of time, you will notice that the
screen becomes warm. Please note that this is normal.
To prevent scratches or damages to the LCD screen, do not knock or rub
the surface with sharp or hard objects. Clean the screen with a soft cloth
moistened with warm water and dry with a soft cloth. A mild soap may be
used if the screen is extremely dirty. Do not use harsh or abrasive cleaners!
CAUTION
Use a soft cloth to clean the cabinet and the control panel of the TV. When
excessively soiled, dilute a neutral detergent in water, wet and wring out the
soft cloth, then wipe the TV and afterwards wipe it off with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner,
powder soap, Electronic equipment cleaner, car wax, glass cleaner, etc.
especially because they would cause discoloration, scratches or cracks.
FEATURE
Enhanced definition LCD panel
The 32-inch color LCD display panel, with a resolution of 1366 (H) x 768 (V)
pixels, creates a widescreen picture. This panel features a thin form factor
and can be hung on a wall with an optional wall mounting kit.
High Performance Digital
Processor
This panel displays a wide range of personal computer signals from 640 x
350, 640 x 400 VGA to 1360 x 768 .(RGB Analog input)
Easy-to-use remote control and on
screen display system
The included remote control operates all TV functions. Further, the on-
screen display system, shows the status of the control settings in an easy-to-
view fashion.
Power saving system
The International ENERGY STAR® power saver feature saves power
consumption automatically when input signals are not available.
When connected to a VESA DPMS-compliant PC, the monitor cuts its power
consumption while it is idle.
is a trademark of SRS Labs, Inc. TruSurround XT
technology is incorporated under license from SRS Labs, Inc.

5
ENGLISH
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS.........................2
SAFETY INSTRUCTIONS ...............................................6
INSTALLATION INSTRUCTIONS.................................10
Desk Top Stand ..........................................................10
Anti-Tipping Prevention...............................................10
Power Cord Connection..............................................11
Connecting Antenna / Cable TV Signal ......................12
Connecting to Video Components ..............................13
INSTALLATION INSTRUCTIONS (continued) ............14
INSTALLATION INSTRUCTIONS (continued) ............14
Connecting to a PC.....................................................14
COMPONENT NAMES ..................................................15
Main Unit ...................................................................15
ATTENTION................................................................16
COMPONENT NAMES (continued) .............................17
Remote Control (continued)......................................17
OPERATING INSTRUCTIONS......................................18
Turning Power Off.......................................................18
Selecting AV Inputs.....................................................19
Volume Adjustment .....................................................19
Audio Mute ..................................................................19
Using the Menu Screen (On-screen display system) 20
Image Settings............................................................ 21
Display Settings .......................................................... 22
Display Settings .......................................................... 23
Display Settings .......................................................... 24
Advanced PC.............................................................. 25
Audio Settings............................................................. 25
Setup ..........................................................................26
Channel Setting .......................................................... 27
ASPECT .....................................................................31
Teletext Menu ............................................................. 32
TROUBLESHOOTING...................................................33
Symptoms................................................................. 33
Abnormal Displays Corrections VGA Only ............... 36
PRODUCT SPECIFICATIONS......................................37
Component Connection............................................ 38
Component Connection............................................ 38
Recommended Signal List……………………………39
Notes about this manual
The information in this manual is subject to change without notice.
While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have any comments, views or
questions about our product.
Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, when using the product. We are not held
liable for damages caused by improper handling of the product.
Reproduction of this manual in whole or in part without our prior written permission is prohibited.
The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.

6
SAFETY INSTRUCTIONS
This LCD TV has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to
obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions
About the Symbols
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the users and to prevent
property damage. The meaning of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the
contents.
WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect
handling.
CAUTION This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to
incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or adjacent to the symbol (the symbol to the left
indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or adjacent to the symbol. (the symbol to the left
indicates that the power plug should be disconnected from the power outlet).
WARNING
Never use the TV if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables, penetration
of liquids, or foreign matter, can cause a fire or electrical shock.
In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the
smoke or odor has cleared, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.
Disconnect the plug
from the power
outlet.
Do not insert foreign objects or pour liquids inside the TV.
Penetration of liquids or foreign objects could result in a fire or electrical shock. Use special caution in households where children are
present.
If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the power
outlet and contact your dealer.
Do not place the TV in a bathroom.
Do not expose the TV to rain or moisture.
Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc. on or around the TV.
Do not place metals, combustibles, etc. on or around the TV.
Never disassemble or modify the TV.
The TV contains high voltage components. Modification could result in a fire or electrical shock.
Never remove any cover. Do not disassemble.
Do not subject the TV to shock or impact.
If the TV is subject to shock and/or is broken, it could result in an injury, and continued use in such a state could result in fire or electrical
shock. If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet and
contact your dealer.
Do not place the TV on an unstable surface.
If the TV should be dropped and/or broken, it could result in an injury, and continued use in such a state could result in fire or electrical
shock. Do not place the TV on an unstable, slanting or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the TV.
If ventilation is obstructed during the operation of the TV or just after switching off the power, it could result in damage and shorten the
lifespan of your TV due to overheating. Make sure there is ample ventilation.
Keep a space of 100mm (10cm) or more between the sides, rear and top of the TV and other objects such as walls.
Do not place anything around ventilation openings of the TV.
Never block ventilation openings.
Do not put the LCD screen side up.
Do not cover the TV with a tablecloth, etc.
Do not place the TV on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use the correct power outlet depending on the indication on the TV and the
safety standard.
The enclosed power cord must be used depending on the power outlet to be used.

7
ENGLISH
SAFETY INSTRUCTIONS (continued)
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
Do not touch the power cord with a wet hand.
Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.
Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an
appropriate extension lead or consult your dealer.
Be sure to ground the connection properly.
Connect the ground terminal of the AC inlet of this TV with the ground terminal provided at the power outlet using the enclosed power cord.
If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet. Surely connect the
ground wire.
Be careful when handling the power cord and external connection cables.
Do not use damaged power cords or cables as they can cause a fire or electrical shock. Do not apply excessive heat, pressure or tension
to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
Do not place the TV or other heavy objects on the power cord and cables. Also, do not place a spread, cover, etc., over them as this could
result in the inadvertent placing of heavy objects on the concealed power cord or cables.
Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug
or connector.
Do not place the power cord near a heater.
Do not touch the power plug just after disconnecting it from the power outlet. The static discharge can cause an electric shock.
Do not touch the power plug during a lightning storm.
Avoid coiling the power cord and bending it sharply.
Protect the power cord from being walked on or pinched at particularly at plugs, conveniences receptacles, and at the point where they exit
from the panel.
Do not modify the power cord.
Be careful when handling the batteries of the remote control.
Incorrect handling of the batteries could result in a fire or personal injury. The batteries may explode if not handled properly.
Keep the batteries away from children and pets. If swallowed, consult a physician immediately for emergency treatment.
Do not allow the batteries to be exposed to fire or water.
Avoid fire or high-temperature environments.
Do not hold the batteries with metallic tweezers.
Keep the batteries in a dark, cool and dry place.
Do not short circuit the batteries.
Do not recharge, disassemble or solder the batteries.
Do not physically impact the batteries.
Use only the batteries specified in the manual accompanying this TV.
Make sure the plus and minus terminals are correctly aligned when inserting the batteries.
If you observe a leakage of the batteries, wipe out the liquid and then replace the batteries. If you spill the liquid on your body or clothes,
rinse well with water.
Obey the local laws when disposing the batteries.

8
SAFETY INSTRUCTIONS (continued)
CAUTION
Be careful in moving the TV.
Neglect could result in an injury or damage.
Do not move the TV during use. Before moving, disconnect the power plug and all external connections.
Get the help of another person if you find it difficult to move the TV alone.
Avoid any impact or shock to the TV; in particular take care of the glass screen.
Do not put anything on top of the TV.
Placing anything on top of the TV could result in loss of balance or falling, and can cause an injury or damage. Take special care in
households where children are present.
Avoid a humid or dusty place.
Placing the TV in a smoke filled, or in a highly humid, dusty place with oily soot or corrosive gas could result in fire or electrical shock.
Do not place the TV near the kitchen, a humidifier or any other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the TV and its components, and could result in transformation, melting or fire.
Do not place the TV, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
Do not put the TV in a place where the temperature varies rapidly.
Remove the power cord when not using the TV for a long time.
For safety, disconnect the power cord if the TV is not to be used for prolonged periods of time.
Before cleaning, turn off and unplug the TV. Neglect to do so could result in a fire or electrical shock. Disconnect the plug
from the power
outlet.
PRECAUTIONS
Installation environment
Do not obstruct the ventilation slots.
Do not place the TV on a carpet or blanket, or near a curtain or anywhere else where there is a possibility of obstructing the ventilation slots of the TV.
Do not place the TV in the following places.
Hot places such as near heaters, or in places exposed to the direct rays of the sun.
Places where the temperature varies rapidly.
Places with soot, dust or high humidity.
Places with poor ventilation.
Places such as near a fire.
Wet places such as bathrooms, or shower rooms.
Places where you can trip over the TV.
On objects that vibrate.
On objects that are unstable.
How to view the TV
If you use the TV in too dark a room, your eyes may become tired.
Use it in a reasonably bright room.
Avoid direct rays of the sun on the screen to prevent eye fatigue.
Your eyes will get tired after viewing the TV for long periods of time.
Relax your eyes by looking away from the TV from time to time.
Please watch the TV in downward direction.
How to clean the LCD screen panel of the TV
Before cleaning the TV, turn off the TV and disconnect the power plug from the power outlet.
To prevent scratching or damaging the LCD screen, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth moistened
with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.
How to clean the cabinet of the TV
Use a soft cloth to clean the cabinet and control panel of the TV. When excessively soiled, dilute a neutral detergent in water, wet and wring out the soft cloth,
wipe the TV and afterwards wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. as they could cause
discoloration, scratches or cracks.

9
ENGLISH
SAFETY INSTRUCTIONS (continued)
Prevention of an obstacle to Radio receivers
This TV has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
Keep the TV away from Radio.
Adjust Radio antennas in order for the TV not to receive interference.
The antenna cable of Radio should be kept away from the TV.
Use a coaxial cable for antenna.
You can check if this TV influences Radio receivers by turning off all other equipment other than the TV.
If you find a problem receiving Radio when using the TV, check the instructions mentioned above.
Precautions for the cable connection
Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are properly made and in
accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing connections.
Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
Plug the power cord of the TV into a different socket from that for other equipment, such as Radio etc.
Use a plug with ground terminal and make sure that it connects to the ground.
Precaution during transportation
Please pay attention when you transport this TV because it is heavy.
Furthermore, use the original carton box and its packaging materials when the TV is transported.
Failure to transport the TV in any carton except the original carton may result in damage to the TV.
Save the original carton box and all packing material.
Do not physically impact the remote control.
A physical impact could cause damage or malfunction of the remote control.
Take care not to drop the remote control.
Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
Avoid radio generator such as a mobile telephone, transceiver, etc. around the TV.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
Precautions for the installation
Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved stand or legs with the
fixings provided according to the instructions.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the
cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
Only use the attachments/accessories specified by the manufacturer.
Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
Other precautions
Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a stand-by mode.
Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or handicapped people.
Disposal of this product may require specific instructions pertaining to your resident region.
Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!

10
INSTALLATION INSTRUCTIONS
Desk Top Stand
WARNING
Use one of the special mounting units to install this product. A mounting unit of insufficient strength or inadequate design can cause overturning or dropping
and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries or property damage
caused by use of other mounting units or improper installation.
CAUTION
Do not attempt installation of the wall mounting unit and ceiling mounting unit by yourself as it can be dangerous. Ask
your dealer to provide the name of a qualified technician.
In order to prevent overheating, maintain a space of 10cm (4 inches: For a desktop setup) or more between the sides of
the TV and other objects such as walls, etc., so that the ventilation holes are not blocked.
Anti-Tipping Prevention
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.
TV
Desktop stand
10cm (4 inches) or more*
Clamp
Cord
or
chain
Hook
Chain
Clamp
Clamp
Cord or chain
Wall or Pillar

11
ENGLISH
INSTALLATION INSTRUCTIONS (continued)
Power Cord Connection
Connect the power cord, after completing all other connections.
1. Connect the power cord to the rear of the TV.
2. Connect the power cord plug to the power outlet.
3. Turn ON the main power switch is located on the side
(The type of plug is different from this drawing for some countries.)
CAUTION
Use only the power cord provided.
Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.

12
INSTALLATION INSTRUCTIONS (continued)
Connecting Antenna / Cable TV Signal
Make sure that the power switch of the TV is turned off.
1. TV IN connector (Analog) Connect an antenna or a cable TV box using the coaxial cable
2. HDMI IN connector Connect devices such as a DVD player or set-top box
3.PC Audio connector for VGA Connect the audio cable from your computer
4.VGA connector Connect to the VGA cable from your computer to the TV
5. Component audio and video connectors (AV3/AV4 IN) Connect devices such as a DVD player, set-top box, or cable TV box
6. AV-out & Subwoofer audio out connectors AV-out connect devices such as a VCR, Subwoofer audio out connect an optional powered subwoofer to the TV.
7. Composite video, S-Video and audio connectors (AV1 IN) Connect devices such as a VCR or DVD player
8. Side I/O (AV2 IN) S-Video , composite and audio connectors Connect devices such as a video game system or a DVD player and turn on or turn off the
Main power switch the power of your appliance.
9. Power connector Connect your power cord
Precautions when connecting the antenna
Use a coaxial cable which is free from interference. Avoid using a parallel flat wire as interference may occur, causing the reception to become unstable and
noise to appear on the screen.
Avoid using an indoor antenna as this may be affected by interference and poor reception.
Keep the power cord as far away from the antenna wire as possible.
VHF(300-Ohm) antenna / UHF antenna
When using a 300-ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to the screws of the VHF or UHF adapter. Plug the
300-ohm to 75-ohm adapter into the antenna terminal on the TV.
When both VHF and UHF antennas are combined
Attach an optional antenna cable signal combiner to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your local
electronics retailer.
TV rear panel

13
ENGLISH
INSTALLATION INSTRUCTIONS (continued)
Connecting to Video Components
1. Make sure that the power switch of the TV is turned off.
2. Make sure that the power switch of the Video component is turned off.
TV Quick Connection
A
ERIEL
CAMCORDER
S-CABLE
DVD PLAYER Cable/Satellite
Decoder Box
VCR
ANTENNA
Better Connection
U.K. ONLY
S-CABLE
Side I/O (AV2)
[An example of connecting video components]
If the OUTPUT RCA terminal is connected to a 2nd monitor, it is possible to view the same image as on the main source. The composite video signal from
CVBS input will be displayed on both screens at the same time.
Applicable video signals for each input terminal
(See page 38, 39 for details)
Terminal RCA / 4Pin Mini Din HDMI D-Sub
Signal CVBS S-Video Component Video RGB
AV1 {{
AV2 {{
AV3 {
AV4 {
HDMI {
VGA
{
({: Avaliable)

14
INSTALLATION INSTRUCTIONS (continued)
Choose an appropriate site and install the product on a level table where the stand is secure.
Ensure that a power socket is readily accessible near the place where you install the TV.
Make sure that the power switch of this device is turned off.
Connecting to a PC
1. Make sure that the display signal of the personal computer to be used is compatible with the specifications of this device.
See "Product Specifications" concerning the specifications of this device.
2.Make sure that the power switch of the personal computer is turned off.
3.Connect the signal input terminal VGA on the rear panel of this device to the display signal output terminal of the personal
computer.
Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with the personal computer
may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the personal computer manufacturer or your
local retail dealer.
Note
When running 1360x768 resolution on a PC, be sure to run auto adjust to align the picture correctly.
Subwoofer Output provides a single un-amplified audio output that passes along the audio signal from the LCD TV.
Note: When using a Home Theater audio system with this LCD TV, please connect the sub woofer (if originally supplied with the audio
system) directly to the Home Theater components subwoofer terminal.
TV rear panel
Power cable
connector
3.5mm
Stereo
Audio
Cable
To Audio
Output
15 Pin D-sub
VGA
connector
To Video
Output

15
ENGLISH
COMPONENT NAMES
Main Unit
Front
Caution when moving the main unit
As this product is heavy, whenever it is moved, two people are required to transport it
safely.
Whenever the unit is moved it should be gripped on the top of the panel and the unit
should then be held at the base on both sides for stability as shown.
Rear
Cabinet
(Front Frame)
Pane
Indicator lamp
These buttons are located on the top.
Control Panel
The main power switch is located at the back, on the
lower surface.
CHANNEL buttons
( Adjust the TV Channel)
or power on
SOURCE buttons
(mode selection)
ENTER button
(adjusting or next page)
POWER button
Press the television panel
power button.
(32”)
Main power source button.
Press the main power
source button.
External device connection terminals
MENU buttons
(function or return one step)
VOLUME buttons
( ADJUST buttons)

16
COMPONENT NAMES (continued)
Remote Control
Installing the Batteries Handling the Remote Control
1. Open the battery cover.
Slide back and remove the battery cover in
the direction of the arrow.
2. Installing the batteries.
Install two included Size AAA batteries
observing the correct polarities(+,-).
Use the remote control within about 16 feet from front of the unit’s remote-
control sensor and within 30 degrees on both sides.
3. Close the battery cover.
Replace the battery cover in the direction of
the arrow and snap it back into place.
Do not mix new and old batteries together. The batteries could explode or leak,
resulting in fires, physical injury, or stains.
When inserting batteries, observe their correct polarities as marked on the
product. If inserted in the wrong direction, the batteries could explode or leak,
resulting in fires, physical injury, or stains.
ATTENTION
Do not drop the remote control.
To avoid possible failures, do not splash the remote control with water or
put it on a wet object.
If leaving the remote control out of use for an extended period of time,
remove the batteries from it.
If the remote control does not respond properly, replace the batteries.
Strong light such as direct sunlight exposed on the photoreceptor of the
remote control can cause operational failure. Position this unit to avoid
direct contact with such light.
LED INDICATION
AV4
ASEPCT
PICTURE
HOLD
MENU
PROGRAM / ADJUST ()
DISPLAY
TV TUNER
SOURCE
PC
TEXT
MUTE
NUMBER KEYPAD
Within 30 degrees Within 30 degrees
About 10 feet About 10 feet
About 16 feet
CAUTION
INDEX
SUB
AV1
MODE
REVEAL
CANCEL
SIZE
A
V2
HDMI
A
V3
ENTER
I/II
SELECT ()
RETURN
RECALL
SLEEP
VOLUME ()
CH () or powe
r
on
POWER ON/OFF

17
ENGLISH
COMPONENT NAMES (continued)
Remote Control (continued)
POWER SOURCE
Press this button to turn the TV on or off. OSD source selec input menu
MUTE AV3
Press this button to turn off the sound. Press it
once more or press the volume up button to
return the sound.
Switch to input source AV3
Component YcbCr/YPbPr
DISPLAY AV2
Press this button to show the input signal
information Switch to input source SideIO AV2
composite(default) or AV2 Svideo
TV AV1
Press this button to choose TV as the source. Switch to input source AV1
composite(default) or AV1 Svideo
CHANNEL (CH) PC
TV select channels up or down or DC power-on Switch to input source PC
VOLUME ( VOL) AV4
Press these two buttons to adjust the
volume up or down
Switch to input source AV4
Component YcbCr/YPbPr
RECALL HDMI
TV switch to last channel program Switch to input source HDMI
SLEEP Teletext color Keys
Select timer to turn power off. The default timer
is 30, 60, 90 and 120 minutes (Only enable in
TV function).
Turn ON/OFF conceal information.
0~9 Number Keys REVEAL
Used to select cable TV or Terrestrial programs. For special teletext functions
PICTURE MODE
Picture image scheme mode (Personal, Sport,
Game, Movie, Vivid) Teltext Turn ON/OFF list mode.
ASPECT INDEX
Selcet how the picture is displayed on the screen;
pillar box, letter box expand, Panoramic, or Cinema
modes
Teltext Turn page to index page.
RETURN TEXT
Return to last level OSD menu Turn the Teletext function ON/OFF
MENU CANCEL
Turn on the OSD menu. Press the CANCEL button again into
display the TELETEXT screen
SIZE
Adjust the selected item on menu or adjust the
volume. Teltext font size change
HOLD
* Press to select desired item on the menu
* Press to select desired page on the text mode
Teltext hold funtion
SUB
Enter key, confirm OSD select function Teltext SUB function
I/II
TV multi-language sound system select

18
OPERATING INSTRUCTIONS
Turning Power Off
1. To turn the TV power OFF, press the power buttonor the
power button on the remote control.
Note: During normal use, the main power switch is set in the ON position.
Power lamp
Power
lamp
Power
Status Operation
Dark Off
When the main power switch is set to
OFF.
RED Off
(standby)
When the main power switch is ON, and
the OFF button on the remote control or
the SUB POWER button is OFF.
GREEN On
When the main power switch is ON, and
the Power or Channel up/down button on
the remote control or the Power or
Channel up/down button is ON.
AMBER Off
(Power Save)
When the main power switch is ON, and
the PC is in power save mode.
When the indicator lamp lights Amber or the message “No cable
connected” or “Going to sleep” appears on the screen, there is
something abnormal about the status of the reception.
See Trouble Shooting.
CAUTION
Avoid repeatedly turning the TV on and off at short time intervals. Failures
might result from doing so.
Turn off the main power switch before leaving the TV out of use for an
extended period of time.
If a power failure occurs while the main unit is running, it would be powered
on upon recovery from the failure. Turn off the main power switch when a
power failure occurs.
Power Lamp
POWER OFF
1
2
Main power switch
SUB-POWER button

19
ENGLISH
Selecting AV Inputs
Input can be switched by pressing the TV, AV 1,
AV 2, AV 3, AV 4, HDMI, PC buttons
Input can be switched in the sequence TV AV 1
AV 2  AV 3  AV 4  HDMI  VGA by pressing the
SOURCE button and then select the Input with the select keys
 and then press the ENTER button.To select a TV
station, press the TV button.
TV AV1 AV2 AV3
PC HDMI AV4
Volume Adjustment
The volume can be adjusted by pressing the and buttons
of the remote control (or the < - and >+volume buttons of
the TV).
When the volume buttons are pressed, the volume adjustment
status guide will be displayed.
The volume will increase when the VOL+ (or ) button is pressed while
the guide is being displayed.
The volume will decrease when the VOL- (or ) button is pressed while
the guide is being displayed.
Audio Mute
The audio volume can be temporarily muted by pressing the
MUTE button of the remote control.
When the MUTE button is pressed, the above icon will appear.
The volume setting can be lowered by pressing the VOL- button while the
audio is muted.
Muting can be cancelled by pressing the VOL+ button or the MUTE button
while the audio is muted.
OPERATING INSTRUCTIONS (continued)
Volume setting value
Adjustment status guide
TV
SOURCE
MUTE
VOLUME
CONTRO
SELECT 
VOLUME buttons
SOURCE button