DIVIN DV6 Series User manual

User Manual
Dual-Zone Wine Fridge
www.divinwinefridges.com.au

Thank you very much for choosing DIVIN wine fridge
to store your precious collections! We hope you may enjoy using it.
Purchase Date:
*The purchase date is the date when the warranty begins.
Serial Number:
*The serial number is located on the data plate, which can be
found on the inner wall of the wine fridge. Please write down your
serial number in the blank.
Please staple your invoice to your user manual.

General Instructions Before Usage
This appliance is not intended for children, please pay attention to their safety.
To ensure the cooling system may function properly, after this wine fridge has been
laid down during transportation and delivered, allow it to rest unplugged in a standing
position (with the base situated on the floor) for at least 24 hours before turning on
for use.
Check the conditions of the product and take photos as you are receiving it from the
delivery company. Inform them immediately when noticing any damages caused
during transportation.
Install the appliance only on a sturdy, flat, and level surface and be cautious during
the installation at all times.
Keep any packaging materials if needed for the future and keep them away from
children.
Make sure your power supply sources have met all the electrical standards required
by laws. DO NOT use extension cords; use an exclusive and properly installed outlet
instead.
Further assistance from DIVIN
Website-Support: https://divinwinefridges.com.au/support/
E-mail: [email protected]
Tel: [phone]
Business Hours: 7:30-16:00 (Mon.-Thu.) | 7:30-14:00 (Fri.)

Table of Contents
General Instructions Before Usage..........................................
Installation................................................................................
Important Safeguards & Warnings...........................................
The Touch Controls and Operation..........................................
Wine Rack & Bottle Configurations..........................................
Temperature Setting & Energy Saving Recommendations......
Bottle Capacity.........................................................................
Care and Maintenance.............................................................
Troubleshooting Guide.............................................................
Warranty and Terms.................................................................
1
3
5
6
7
8
11
12
13
15

Important Safeguards & Warnings
All the instructions of this user manual must be read and adhered carefully to ensure
safety, proper performance of the product, and the validity of DIVIN’s warranty.
This wine fridge is designed for commercial and residential indoor environments
(excluding garages and other places that can have extreme temperature shifts) only
for storing a wide variety of wines. If the wine fridge is used for purposes other than
wine storage and causing damages to the unit directly, then we cannot provide full
warranty.
To avoid electric shock, DO NOT use the wine fridge or wire plug near wet locations.
Also, DO NOT operate the product with wet hands.
Your wine fridge was designed to operate in temperature settings between 5°-35°
Celsius. If the temperature is higher or lower than this range, the function of the wine
fridge will be affected and the temperature of the wine fridge may be unstable or may
not reach the desired temperature.
DO NOT place the wine fridge near any heat sources (e.g. gas stoves, heaters, etc.)
and in direct sunlight.
Wine fridges with compressors are not noiseless and may produce different sounds
when in use. Therefore, it is not recommended to install them in bedrooms.
When cleaning, DO NOT spray any cleaning chemicals around the front exhaust
openings and the back of the appliance. This can avoid damages to the metal pipes
that are around the compressor. When damages happen, refrigerant may leak and
eventually cause the malfunction of the cooling system.
Extension cords are not recommended. Use a separate outlet that complies with the
safety regulations. Never unplug the unit by pulling on the power cord. Always grasp
the plug firmly and pull straight out from the outlet.
This appliance is not intended for use by children, please pay attention to children's
safety.
Keeping the interior and exterior of your wine fridge clean and tidy and avoiding any
spillage of wines inside the unit.

When stop using the product for a long time, open the door to ventilate to avoid
excessive moisture staying inside the unit. After that, lock the door to prevent chil-
dren from being injured.
Make sure the environment, where the appliance is used, is well-ventilated and the
front exhaust openings are not blocked by any objects that may prevent proper air
circulation.
The wine fridge is equipped with an auto defrost system. Please DO NOT use other
methods to speed up the defrosting process.
When relocating the unit, remove the wines stored inside first to reduce the weight.
The warranty applies only to the wine fridge itself and does not cover the items
stored items.
If you wish to dispose of this product, please send it to an authorized large electrical
recycling facility.

DV-636DK Smart Touch Control Panel
*Smart touch control panel is touch-sensitive, just touch the button to operate, no need to press hard.
Left and right temperature display
The number on the left side of the touch panel screen is the temperature display of the
upper-temperature zone, and the number on the right side is the temperature display of the
lower-temperature zone.
For example: when the left number shows 14, the upper-temperature zone is 14°C, when the
right number is 12, it means the lower temperature zone is 12°C
Power button
Turn ON/OFF:
Touch the Power button once and hold for about 3 seconds for turning on the unit. Repeat again
until seeing a “3, 2, 1” countdown to turn off the unit.
NOTE: The countdown is designed for preventing turning the unit off accidentally.
Temperature setting lock/unlock button
To prevent the temperature setting of the wine fridge from being changed by accident, this
fridge allows you to set the temperature after you press this button for 3 seconds.
If you do not press any button after unlocking, it will lock automatically after about 20
seconds.
Temperature adjustment up/down arrow
To adjust the temperature setting, tap the up arrow once to increase 1°C, and tap the
down arrow once to decrease 1°C.
Temperature zone selection
Select the temperature setting of the upper either or lower temperature zone, and view the
current temperature of the upper and lower temperature zones of the wine fridge by using
this button. Press this button after the temperature setting is unlocked, and the touch
control panel will display the current temperature settings for the upper and lower zones.
The temperature of the upper-temperature zone on the left will be flashing first, and then
press this button again to select the temperature of the lower-temperature zone on the
right. The temperature can be set with the temperature up/down button before the number
stops flashing. When the flashing is finished, the temperature setting is completed.

3-In-1 LED side light / °F / °C switch
LED light switch:
LED side light has 3 colors to choose from (Icy blue/Rose pink/Moon white), press this button
1 time to switch to another color.
Automatic light on/off mode:
The initial setting of the wine fridge is automatic light on mode, the LED light will be on
automatically after the door is opened, and will be off automatically after the door is closed.
Long-lasting light mode:
If you want to keep the LED light on after the wine fridge door is closed, press this button for
about 3 seconds and stop after you hear a beep sound. Repeat the same steps to turn off this
mode and return to the automatic light on/off mode. The light color will return to icy blue as the
first display color.
°F / °C switch:
Press this button for 3 seconds to hear the first beep and do not let go until you hear the second
beep, this is when the switch is completed. Repeat the same action to restore the temperature
unit before the adjustment.
Close door reminder alert
Press this button for 3 seconds to hear the first beep and do not let go until you hear the
second beep, this is when the switch is completed. Repeat the same action to restore the
temperature unit before the adjustment.
When the temperature of the wine fridge is over 23°C or lower than 0°C, an alarm with beeps will
begin, which will stop once the temperature is lower than 23°C or higher than 0°C.
NOTE: The alarm can be deactivated by pressing any buttons on the control panels.
High/Low Temperature Alarm

Temperature Setting Tips:
The temperature of the wine fridge can be set to accommodate your wine collections and storage
requirements. If your collections include age-worthy and ready-to-drink wines, we recommend to
designate the left cabinet for ready-to-drink and the right cabinet for maturation or vice versa.
The best temperature for maturing wines is around 12-14°C.
NOTE: Lower temperatures (12-14°C) are better for achieving ideal maturation at a normal rate,
while high temperatures will speed up the maturation process, but do not necessarily result in
good results.
The temperature of the ready-to-drink cabinet can be set according to the serving temperature
of the type of wines that are stored in that cabinet. In general, the ideal serving temperature for
red wine is anywhere between 15-18°C; 10-14°C for whites and rosés; 6-8°C for dessert wines;
5-10°C for sparkling wines. However, the actual optimal serving temperature depends on the
characteristics of the wine (wine body, vintage, whether it has been aged in oak barrels, etc.).
Therefore, please refer to the recommendations provided by wineries for the ideal serving
temperature of their wines.
Temperature Setting & Energy Saving Recommendations
● Install the wine fridge in a cool and ventilated area and away from any heat sources (e.g. sun
light, ovens, less insulated spaces, etc.).
● Avoid opening the doors frequently or for too long.
● Set the temperature around 12-14°C for both temperature zones (the left and right cabinets);
not only is it more energy saving, but also helps store any wines for a long term and serves
whites and rosés at the same time.
● Set the two temperature zones at the same temperature.
Energy Saving Tips:

*To avoid collisions between the bottles on the upper and lower display shelves due to different sizes, it is recommended
that narrower bottles (e.g., A and E bottles) be placed on the lowest shelf of each temperature zone before starting to
place wider bottles (e.g., B, C and D bottles).
*If you can't fit in a wide bottle, you can remove the beech wood shelves (see page 1 for disassembly video instruction) to
make enough space.
*Before the display shelf is removed for more room, you can place about 8.3 cm diameter Burgundy bottles on the front
horizontal area, but bottles with diameter of 8.5 cm or more are not recommended, because the bottle will protrude and
touch the display shelf above, causing the shelf to work unsmoothly when used. If you wish to place a bottle that is just
under or over 8.5 cm in the horizontal area of a particular display, it is recommended that you remove the display shelf
above that shelf. The display shelf above the shelf can be removed to make more space.
*The horizontal area at the front of the first shelf in the lower temperature zone is recommended for Bordeaux bottles
only, to avoid collision with the bottles on the shelf directly above it.
*When a Burgundy bottle is placed in the horizontal area at the front of a shelf, Bordeaux or Burgundy bottles (750ml) can
be placed in the back row of the shelf directly above it, but the bottoms of these bottles must be placed on the dented
area at the back of the display (as shown in the picture above) to prevent the bottles on the top and bottom shelves from
collisions when pulling the top shelf.
7.6
7.6
19.1
30.1
A
8.2
13
29.5
B
12
32
8.8
D
8.5
11
30
C
7
11
26.2
H
6.5
11.5
24.2
G
6.1
14
23.6
F
9.8
21.5 36
I
10.6
15.5
35.5
J
14
33
E
The following is our recommendation on proper wine storage,
which can also be used as a reference for other similar size bottles.
*The schematic diagram of the wine bottle shows the approximate size (unit: cm)
Wine Shelves & Bottle Configurations
Standard Bordeaux
750mL
Burgundy
750mL
Burgundy
750mL
Sparkling or Champagne
750mL
Riesling
750mL
Burgundy
375mL
Champagne
375mL
Bordeaux
375mL
Burgundy
1.5L
Bordeaux
1.5L

B
B B B
E E
E
B B B BB
E E
B
B
E E
F
F
G
G
H
H
B
B
B B B BB
C C C C C
Display shelves
B
B
E
E

C C C
E
E
E E
C C C C C
F
G
C C C
B
B
B B
Display shelves
The top upper-temperature zone fixed shelf
*Please make 5 D bottles of the back row facing outward of the fridge, the front row can fit 375mL of F, G,
and H bottles or mix and match with A, B or E bottles.
*Please be sure to make stacked bottles on the back row of the second layer facing outward of the wine
fridge, and before pulling out this layer of shelves, take out the second layer of the leftmost and rightmost
bottles (dotted line area) first to avoid slipping.
D D D D D
F
H
D D D D D
G
H
D D D D D
H
Fits two layers of A bottles in the back
row, 5 bottles on the first layer; 6
bottles on the second
B
B B B B B B
E
E E E E E E
Stacks 5A bottles on the first layer of
the back row. 6 B bottles / 5 C bottles
/ 5 D bottles on the second layer
Stacks 5A bottles on the first layer of
the back row. 6 E bottles on the
second layer

Normal shelf (First layer of the lower-temperature zone)
*When the shelves are stacked with two or three layers of wine,
we recommended storing only A bottles or smaller diameter bottles in the horizontal area of the display shelf
right below. This can avoid contact between the bottles on the normal shelf and the display shelf.
C
B
C
B
C
C C C
B B B
D D D D D
C C C
D D
B B B B B
D D
E E E
E E E E E

Normal shelf (First layer of lower-temperature zone) stacking
The upper-temperature zone
fixed shelf
The bottom fixed shelf of the
lower-temperature zone
The bottom fixed shelf of the
lower-temperature zone
The bottom fixed shelf of the
lower-temperature zone (Storage mode)
*When the bottles are stacked, there’s no need to pull this shelf to get the wine or place the wine; if you need
to pull this shelf, please take out the bottles on the dotted line first to avoid slipping.
The upper-temperature zone
fixed shelf
The upper-temperature zone
fixed shelf (Storage mode)
Horizontal placement of 2 bottles in the
back row and 6 bottles in the front row.
*Fits 6 A bottles / 6 B bottles / 6 C
bottles
The area above the arch at the end of this
layer fits 1 I bottle / 1 J bottle.
The front row fits 3 I bottles / 3 J bottles
*Take off one display shelf above before
placing 1.5L bottles and use kneaded
erasers to avoid slipping.
Stacks three layers of A bottles.
Place 2 bottles horizontally above the dent
in the back row of the first layer.
Place 6 bottles in the front row.
Place 5 bottles on the second layer;
4 bottles on the third layer.
*Take off one display shelf above the fixed
shelf before use
Stacks 4 I bottles / 4 J bottles
*Take off one display shelf above the
fixed shelf before use.
Stacks three layers of A bottles.
Place 2 bottles horizontally in the back row of
the first layer and 6 bottles inon the front row.
Place 5 bottles on the second layer; 6 bottles
on the third layer.
*Take off the two display shelves above
before use
The First layer with 5C bottles;
The second layer with 4C bottles;
the third layer with 5A bottles
A and B bottles can be mixed and stacked,
5A bottles on the first layer;
2A bottles and 4B bottles on the second layer;
The Third layer with 3B bottles.
A and C bottles can be mixed and stacked,
5A bottles on the first layer;
4C bottles on the second layer;
The Third layer with 5C bottles.
I
II I
I
I
I
I
B B B

105
(Standard Bordeaux bottles 750mL)
114
(Standard Bordeaux bottles 750mL)
13
7
7
7
7
7
16
7
7
7
7
6
7
13
7
7
7
19
16
7
7
7
7
17
Bottle Capacity
Storage Mode Standard Mode
*Before pulling out the display shelves, please take out the leftmost and rightmost
bottles in the front row to avoid slipping.
*When stacking wine, please pay attention to whether the total weight of the wine is within the safe load range.
The safe load of the display shelf is about 13kg; the safe load of the upper-temperature zone fixed shelf is
about 19kg; the normal shelf (the first layer of the lower-temperature zone) has a safe load of about 16kg.

Note: Stainless steel is not a material that is completely free from rusting. Regular
cleaning and caring can prevent rust caused by grease and moisture.
Cleaning and Maintenance
● Please keep the interior and exterior of your wine fridge clean and tidy
spillage of wine in the fridge. If there’s any spillage please clean up with
soon as possible.
● Glass Doors:
● Stainless Steel Door Frames, Shelf Trims, and Front Exhaust Grill:
We recommend using stainless steel cleaner to wipe them clean. (Please
cleaning products first on small areas first.)
●
● Activated Charcoal Filter:
We recommend replacing your filter once every year. Replacement frequency
on the condition of your environment. For example, we recommend
frequency of replacement in heavy oil fumes environments.
We recommend using alcohol wipes, glass cleaning cloths, and also glass cleaner to
wipe and clean the outer layer. However, we do not recommend wiping the inner layer.
This can avoid the smell of the cleaning solution remaining inside the fridge and
affecting the wine collection.
Drawer slides:
No need to clean. Apply lubricant for maintenance.

Troubleshooting Guide
Problems
Possible Causes & Solutions
Wine fridge does not operate
Wine fridge is not cold enough
LED side lights are not working
● Check if the unit is plugged into a working power outlet.
● Touch the Power On/Off button once and hold until the
control panel shows the number of temperatures.
● The circuit breaker is tripped or the fuse is blown.
● It takes some time for the wine fridge to cool down after
it has just been turned on.
● The air inside the wine fridge will cool down faster than
the wines.
● Check if the set temperature is too high
● The doors may have been opened frequently or for an
extended period of time so it is losing cold air.
● The doors are not fully closed.
● The sealing strips are not fully sealed.
● Check to ensure the unit is plugged into an outlet.
● Select the correct Lights On/Off button. Touch once to
turn on and touch again to turn off.
● Light bulbs are broken.
● The circuit breaker is tripped or the fuse is blown.
●Wine fridges are not noiseless products and may
produce different sounds when in use, which does not
affect the operation of the unit.
●The compressor makes noise when operating for the
cooling process and it stops when the temperature
reaches the set temperature.
●When the refrigerant is flowing through the piping it can
generate the sound of a water stream. Sometimes the
sound may vary due to the internal structure of the wine
fridges.
●The fans inside the wine fridge can create fan noise
when operating.

The door cannot be shut
properly
The temperature display on
the control panel is higher
or lower than the set
temperature
Compressor runs too
frequently
How to deal with power
outage
● Check if the door were tilted.
● Wine fridge doors are not properly installed
● Check if the set temperature is too high
● Problems with door sealing strips (such as magnetic
losses, displacement, deformation, etc.)
● The shelf was not pushed to the bottom when stored, so
the shelf’s side bar propped against the glass door.
● The wine fridge just turned on
● The indoor Temperature is too high indoors
● Just put in a large amount of wines
● Doors may have been opened frequently or for an
extended period of time, losing cold air.
● In case of power outage, please do not open the door to
prevent the temperature from rising due to the loss of
cool air inside the wine fridge. DIVIN wine cooler is
equipped with a temperature memory function, which
will automatically restore the temperature setting to that
before the power outage.
● Most power outages will be restored within a few hours
and will not affect the temperature of your wine fridge as
long as you leave the doors closed. If you are still wor-
ried about power outages lasting a long period time, you
can seek advice from a professional electrician to install
an uninterruptible power supply (UPS).
● The compressor operates when the temperature inside
the wine fridge is higher than the set temperature and
stops when the temperature drops below the set
temperature.

感謝您購買崧傑股份有限公司的DIVIN系列產品，本公司提供DIVIN系列酒
櫃自到貨日起，全機保固2年(不含附件及消耗品)，壓縮機保固3年(不含電磁閥)。
保固期限內，凡非人為不當操作且正常清潔維護情況下，系統出現任何故障情形，
本公司皆提供免費維修或視情況更換新品服務。
產品保固相關條款：
1. 如超過保固期間需更換零件時，依本公司服務檢修價目表收費，無零件維
修時本公司得以替代零件維修。
2. 保固期間內人為操作不當及損壞者一律酌收外出服務/檢測費及車馬費用，
會另行報價。
3. 產品於保固期間內，經工程師檢測後若屬非保固範圍，本公司報價取得消
費者同意後進行維修並收取費用。
4. 服務人員檢修時，請出示本證書。
5. 本服務保證僅在台灣地區有效。
產品保固免責聲明(若有以下情況，本公司可免除保固責任)：
1. 客戶提供之故障品經確認並非本公司產品。
2. 故障品已超過保固期間。
3. 故障品經人為拆解或重組，不當保養與清潔，做說明書以外之條件之使用
及保存。
4. 故障品來源不正當，屬非法所得者。
5. 商品非經本公司或未授權之經銷商販售。
6. 外觀經人為因素所導致之磨損、刮傷、髒汙及變形等情形。
7. 使用不符合產品本體適用規格內之其他設備及配件所引起故障。
8. 消耗性材料如濾芯。
9. 壓縮機故障造成酒櫃內儲存之各種酒類及其他產品受任何影響。
10. 因天災地變、蟲鼠禍害及未按規定電壓使用所導致故障或毀損者。
11. 商品受特殊環境所影響，如硫磺區、高鹽份沿海地帶、沼氣、化學腐蝕及船上
等容易腐蝕地區。
12. 使用期望、運轉音頻、音量等非功能故障因素。
13. 保證書如有損毀、遺失或塗改致字跡無法辨認。
14. 保固僅適用於酒櫃本身，並不包含保存之內容物。
15. 購買者需承擔使用此設備時會遇上的所有的風險，包含溫溼度變化、藏酒外漏
、火災、水災、霉害、內容物之腐敗、乾燥等其他類似的可能風險。
聯絡資訊
崧傑股份有限公司
(須由崧傑公司簽章及填寫購買日期始能生效)
40654台中市北屯區北屯路366號12樓之1
一般市話：04-2242-2988
免費專線：0800-422988