GEAppliances Profile 20 Operating instructions

GEAppliances.com
Safety Information
Adapter Plugs ................. 4
Electricity ..................... 4
Extension Cords ............... 3
Proper Disposal ................ 3
Safety Precautions ............ 2, 3
Operating Instntctions
Automatic Icemaker ............ 9
Controls ..................... 5
Crispers and Pans ............ 8, 9
Ice and Water Dispenser ........ 10
Shelves, Bins and Racks ........ 6-8
Water Filter Cartridge ........... 6
Care and Cleaning
Cleaning ................. 11, 12
Lightbulbs ................... 13
Installation Instructions
Preparing to Install
the Refrigerator ............ 14, 15
Water Line Installation ...... 16-20
Troubleshooting Tips
Before You Call For Service . . .22-25
Normal Operating Sounds ...... 22
Consumer Support
Consumer Support ..... Back Cover
Performance Data Sheet ........ 27
Product Registration ........ 29, 30
State of California Water
Treatment Device Certificate ..... 28
Warranty (Canadian) ........... 25
Warranty (U.S.) ............... 26
Models20,22and25
C6te _t c6te
R6frig6rateurs
Lasection fran_aisc commence _la page 31
Lado a lado
Refrigeradores
Lasecci6nan cspa_olempiezaan la p_gina59
Write your model and serial numbers here:
Model #
Serial #
Find these numbers on a label inside
the refrigerator compartment at the top
on the fight side behind the controls.
197D3351PO03 49-60189 12-01JR

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
WARNING!
Usethisapplianceonlyforitsintendedpurposeas describedin thisOwner'sManual.
SAFETYPRECAUTIONS
Whenusing electricalappliances,basicsafetypmcautionsshouldbefollowed,includingthefollowing:
m This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
lDo not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
reDo not touch the cold surfaces in the freezer
compartment when hands are damp or weL Skin
may sdck to these extremely cold surfaces.
reDo not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
lIn refrigerators with automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating element
that releases the cubes. Do not place fingers or
hands on the automatic icemaking mechanism
while the refrigerator is plugged in.
II Keep fingers out of the "pinch point" areas;
dearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
lUnplug the refrigerator before deaning and
making repairs.
NOTE:Westronglyrecommend#_atanyservicingbe
performedbyaquafifiedindividual
1Setting the freezer control to the 0(off) position
does not remove power to the light circuit.
IDo not refreeze frozen foods which have
thawed completely.
2

wvv_.GF_Appliance_com
¢LDANGER!RISK OFCHILDENTRAPMENT
PROPERDISPOSALOFTHEREFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous...even if they will sit for "just a few
days." If you are getting rid of your old refrigerator,
please follow the instluctions below to help prevent
accidents.
Before You Throw Away YourOld Refrigerator
or Freezen
ITake off the doors.
II Leave the shelves in place so that children may
not easily climb inside.
CFCDisposal
Your old refrigerator may have acooling system
that used CFCs (chlorofluorocarbons). CFCs are
believed to harm stratospheric ozone.
If you are throwing away your old refrigerator, make
sure the CFC refrigerant is removed for proper
disposal by a qualified servicer. If you intentionally
release this CFC refrigerant you can be subject to
fines and imprisonment under provisions of
environmental legislation.
USEOFEXTENSIONCORDS
Because ofpotentialsafetyhazardsunder certaincondi#ons,we strong/y recommend
against_e use ofanextension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA-listed (in Canada), B-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 190 volts.
3

IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
!1 AWARNING!
HOWTOCONNECTELECTRICITY
Do no_under anycircumstances,cutorremove the third(ground)prongfromthepower cord.For
personalsafe_ this appliancemustbeproperlygrounded,
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock hazard
from this appliance.
Have the wall oudet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
If the outlet is a standard 2-prong ouder, it is your
personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall
outlet.
The refrigerator should always be plugged into its
own individual electrical outlet which has a voltage
rating that matches the radng plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull
straight out from the oudet.
Repairor replace immediately all power cords that
have become hayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When moving the refrigeratoraway from the
wall,be careful not to roll over or damage the
power cord.
USEOFADAPTERPLUGS(Adapterplugsnotpermittedin Canada)
Because ofpotentialsafety hazardsunder certainconditions,we strongly recommendagainst
the useofan adapterplug.
However, ffyou must use an adapter, where local
codes permit, a temporaryconnectionmay be made
to a properly grounded 2-prong wail oudet byuse
of aUDlisted adapter available at most local
hardware stores.
The larger slot in the adapter must be aligned with
the larger slot in the wall outlet to provide proper
polarity in the connection of the power cord.
When disconnecting the power cord from the
adapter, always hold the adapter in place with one
hand while pulling the power cord plug with the
other hand. If this is not done, the adapter ground
terminal is very likely to break with repeated use.
If the adapter ground terminal breaks, DO NOTUSE
the refrigerator until a proper ground has been
established.
Attachingtheadaptergroundterminaltoawalloutlet
coverscrewdoesnotgroundtheapplianceunlessthe
coverscrewismetal,andnotinsulated,andthewell
outletisgroundedthroughthehousewiring.Youshould
havethecircuitcheckedbyaqualifiedelectriciantomake
suretheoutletisproperlygrounded.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY
SAVETHESEINSTRUCTIONS
4

Aboutthe controlsonthe refrigerator. ,_.6_p,,,,,,_
FREEZER FRESHFOOD
Initially, set the fresh food control at 5 and the freezer control at 5 and
allow 12 hours for the temperature to stabilize.
Several adjustments may be required. Adjust the controls one
increment at a time, and allow 12 hours after each adjustment for the
refrigerator to reach the temperature you set.
Setting the freezer control to Ostops cooling in both the fresh food
and freezer compartments but does not shut off electrical power to
the refrigerator.
Control settings will vary based on personal preferences, usage, and
operating conditions and may require more than one adjustment.
5

Aboutthewaterfiltercartridge.
On some models
Water Filter Cartridge
Placethetopofthecartridgeup
mmdethecartridge homerand
slowly turntttothertght
F,br Sma__
0
RESETWATERRLTER
HOLO3SECS
(onsomemodels)
The water filter carmdge is located in the
back upper right corner of the refrigerator
compartment.
When to Replace the Filter on
Models With a Replacement
Indicator Light
There is a replacement indicator hght for
the water filter cartridge on the dispenser.
This light will turn orange to tell you that
you need to replace the filter soon
The filter carmdge should be replaced
when the replacement indicator hght turns
red or ff the flow of water to the dispenser
or tcemaker decreases
When to Replace the Filter on
Models Without a Replacement
Indicator Light
The filter carmdge should be replaced
every Sbrmonthsor earher ff the flow of
water to the water dispenser or icemaker
decreases.
Installing the Filter Cartridge
O ffVou are replaong the carmdge, first
remove the old one by slowly turning It
to the left. Do nntpull down on the
cartridge. A small amount of water may
drip down
On models without a replacement
indicator light, apply the month and
),ear sacker to the new carmdge to
remind you to replace the filter in six
mont_
Fill the replacement carmdge with
water from the tap to allow for better
flow from the dispenser immediately
after installation.
Linmg up the arrow on the carmdge
and the carmdge holder, place the
top of the new cartridge up inside
the holder. 0o o0fpush it up Into
the holder.
Slowly turn it to the right until the filter
carmdge stops DONOT OVER71GHIEN.
As ypu turn the cartridge, it will
automaacafiy ruse itself mto posiaon.
Carmdge will rotate about 1/2 turn
Run water from the dispenser for 3
mmutes (about one and a half gallons)
to clear the system and prevent
sputtering
Press and hold the RESETWATERRLTER
pad (on some models) on the &spenser
for S seconds.
NOTE:A newly-installed water filter
cartridge may causewnterto spun'from
the dispenser.
Filter Bypass Plug
You must use the filter bypass plug
when a replacement filter carmdge LSnot
available. The dispenser and the icemaker
will not operate mthout the filter or filter
bypass plug.
Replacement Filters:
Toorderadditionalfiltercet_qdgesin
MeUnitedStates,visitourWebsite,
ww_.GEAppllanse_cer_orcell
GEPartsandAccessories,800.6262D02.
GWF
Suggested Retail $34 95 USD.
Customers In Canada should consult the
)_ellow pages for the nearest Camco Service
Center
Abouttheshelvesandbins.
Not all features are on all models.
6
Bins on the Fresh Food Compartment Door
Adjustable bins can easily be carried from
refrigerator to work area.
Toremove:Lift the front of the bin up, then
pull out.
Toreplace orrelocate: Engage the bin in the
molded supports of the door, and push in.
Bin vail lock in place
Thesnuggerhelps prevent dpping, spdling
or sliding of small items stored on the door
shelf. Place a finger on either side of the
divider near the rear and move it back
and forth to fit yore- needs

vvww,GEAppliance_com
Rearranging the Shelves
RefrigeratorShelves."
ToRemove
0Uftepand_ QTIt_
FreezerShelve_"
To Remove
ToReplace
kxi _n "'"
FreezerBaskets:
ToRemove
F
Remove the basket by pulling It forward,
lifting up the front, and shchng it past the
stop location
Slide-Out Spillproof Sheff (onsomemodels)
The sfide-out spdlproof shelf allows you to
reach items stored behind others. The
speczal edges are designed to help prevent
spills from dripping to lower shelves
Makesureyoupushtheshelvesall thewayback
mbeforeyouclosethedoor
Spillproof Shelves (onsomemodels)
Spillproof shelves have special edges
to help prevent spills from dnpplng to
lower shelves
Quick Space Sheff (onsomemodels)
This shelf splits in half and shdes under
itself for stowage of tall ttems on the shelf
below.
!
Deep Door Shelves
Detachable shelf extenders deepen and
enclose fixed door shelves, providing
more storage room and greater storage
flexibdlty.
Toremove:Lift the shelf extender strmght
up then pull out.
Toreplace:Engage the shelf extender in the
molded supports on the door and push in.
It wzll lock in place 7

Aboutthe additional features.
Not all features are on all models
ShelfSaver TM Rack
Use this rack to store beverage cans for
easy access
It can also hold a 9" x 13" balung dish.
Aboutthe crispersandpans.
Not a// features are on al/ mode/s.
--\
Fruit and Vegetable Crispers
Excess water that may accumulate m the
bottom of the drawers should be wiped dry
Trivet and Divider (onsomemodels)
The mvet ]s destgned to keep your fruits
and vegetables off the floor of the drawer
and away from any moisture that might
form. The divider will keep the larger fruits
and vegetables from falhng or rolhng onto
the more dehcate ones. By ILffing straight
up on the thvider, you can detach ]t from
the mvet and adjust ]t from side to side,
then push down and into posidon
:--_.. _ ..... Adjustable Humidity Crispers
Shde the control all the way to the
Highor _6 setting to provide high
humidity recommended for most
vegetables
Slide the control all the way to the L0wor
-setung to provide lower humidity
levels recommended for most frmts
8
Co_st
Convertible Meat Pan
The converuble meat pan has its own cold
air duct to allow a stream of culd air from
the freezer compartment to flow around
the pan
The variable temperaturecon_ol regulates
the mr flow from the freezer comparm_ent.
Set control lever up to convert the pan
to normal refrigerator temperature and
provide extra vegetable storage space Cold
air duct is turned off. Variable settings
between these extremes can be selected
Set control lever down to the coldest setting
to store fresh meats If lever ts left in meat
position for a long period of dme, some
frost may form on the inside of the pan.

AboutcrisperremovaL
Not al/ features are on a// mode/s.
Whenreplacingthe crtspers,make
sureyoushdefoemthroughthe
crispergrades.
Crisper Removal
Crispers can easily be removed bv dldng up
shghdy and pulling past stop location If the door prevents you from taking out the crispers, the refrigerator will need to
be rolled forward untal the door opens
enough to shde the cnspers out. In some
cases, when you roll the refrtgerator out,
you wtll need to move the refrtgerator to
the left as you roll tt out
Abouttheautomaticicemaker.
A new/y-mstal/ed refrigerator may take 72-24 hours to begin making ice.
Pow Automatic Icemaker (onsomemode/s)
The tcemaker wall produce seven cubes
per cycle---approxtmately 100-130 cubes
m a 24-hour period, depending on freezer
comparWnent temperature, room
temperature, number of door openings
and other use conditaons
ff the refrigerator is operated before the
water connection ts made to the memaker,
set the power swttch m the 0{off)posmon.
When the refngeratur has been connected
to the water supply, set the power swttch to
the I (on)posmon
The memaker will fill ,hath water when it
cools to 15°E A newly-installed refiagerator
may take 12 to 24 hours to begin making
ice cubes
Throw away the first few batches of ice to
allow the water line to clear
Be sure nothing interferes with the sweep
of the feeler arm.
It is normal for several cubes to be joined
together.
If ice is not ttsed frequently, old tce cubes
vail become cloudy,, taste stale and shnnk
If ice cubes get stuck m the memaker, the
green power light vail blink. To correct thts,
set the power smteh to 0 (off) and remove
the cubes Set the power s_atch to Hen)to
restart the tcemaker. After the lcemaker has
been turned on again, there wallbe a delay
of about 45 minutes before the tcernaker
resumes operaUon
NOTE."Inhomeswithlower-than-averagewater
pressure,youmayhearthe_cemakercyc/emult/p/e
timeswhenmakingonebatchof/ce
There ts an upper freezer sheff
above the tcemaker that can be
used for storage
Ice Storage Drawer
Toaccessice,pull the drawer out. Toremove thedrawer, pull tt straight out
and lift tt past the stoplocauon.
Icemaker Accessory Kit
if)our refrigerator did not come already
equipped wtth an automatic lcemaker,
an lcemaker accessory kit is avmlable at
Check the back of the refrigerator for
the spectfic zcemaker kit needed for
,,'our model
extra cost ,9

Aboutthe ice and water dispenser.
On some models
To Use the Dispenser
SpillSheif
Select CUBEDICE _, CRUSHEDICE
or WATER_.
Press the glass gently against the top of
the dispenser cradle.
The spill shelf is not self-drammg. To
reduce water spotung, the shelf and its
grille should be cleaned regularly
If no water ts dtspensedwhen the refrigerator
is first mstalled, theremay be air m the water
linesystem Pressthe dispenserarm fur at least
two minutestoremovetrappedair fromthe water
hneand tohflthe watersystem Toflushout
impurttlesm thewaterhoe,throwaway thehrst
sixglassfuls of water
CAUTION:Never put fingers or anyother
objectsinto theice crusherdischargeopening
Locking the Dispenser (onsomemodels)
LOCKCONTROL
H_o_3sMs
Press the LOCK
CONTROLpad for
3 seconds to lock the
dispenser and control
panel. To unlock, press
and hold the pad agmn
for 3 seconds.
Dispenser Light
Thzspad turns the
nightlightm the
dispenser on and off.
The hght also comes
on when the dLspenser
cradle ispressed. If this
hght burns out, it
should be replaced
with a 6watt ma.xamum,
12 volt DC bulb
Ice Storage Drawer
on Dispenser Models
Toremove:
Set the zcemaker power switch to the
O{ofO posmon. Pull the drawer straight
out and then lift past the stop posmon.
Toreplace:
When replacing the drawer, make sure
mpush it firmly into place If it does not
go all the way back, remove it and rotate
the drive mechanism 1/4 turn. Then push
the drawer back agmn.
10
Important Facts About YourDispenser
IBDo not add Icefrom trays or bags to
the storage bm Itmay not crush or
dtspense well
IIIIAvoid overfilhng glass with zce and use of
narrow glasses Backed-up ice can jam the
chute or cause the door in the chute to
freeze shut. ff ice is blockang the chute,
poke _tthrough ssath a wooden spoon
Ill Beverages and foods should not be
qmck-chllled m the ice storage bin.
Cans, bottles or food packages in the
storage bin may cause the icemaker
or auger tojam
WTo keep thspensed Ice from mining
the glass, put the glass close to, but not
touching, the dispenser opening.
tl Some crushed ice may be dispensed even
though you selected CUBEDICE.This
happens occasionally when a few cubes
have been left m the crusher.
IllAfter crushed Ice isdispensed, some
water maydrip from the chute.
IllSometimes a small mound of snow will
form on the door in the ice chute. This
condinon ts normal and usuallyoccurs
when you have dispensed crushed Lce
repeatedly. The snow will eventually
evaporate.

Careand cleaning of therefrigerator. , eEAppiianee,
Dispenserdriparea
Cleaning the Outside
The dispmleer dtip am& (on some models)
beneath the grdle, should be wiped dry. Water
left in this area may leave deposits. Remove
the depuslts by adding undiluted vanegar to
the well. Soak until die deposats disappear
or become loose enough to rinse away
Thedispeneercradle (on some models)
Before cleaning, lock the dispenser by
pressing and holding the LOCKCOI_ROL
pad for 3seconds Clean with warm water
and baking soda solution--about a
tablespoon (15 ml) of balong soda to a
quart (1 I) of water Rmse thoroughly
and rape dr,,,
Thedoorhandles and_m. Oean _6di a
cloth dampened wath soapy water DO,
with a soft cloth
Keep the outsideclean.Wtpe with a clean
cloth hghdy dampened with kttchen
apphance wax or mild liquid dish detergenL
Dry and polish wtth a clean, soft cloth
Donot wipe the refrigerator with a soiled dish
clothor wet towel Thesemayleave aresidue
that can erode thepamt Do not usescouring
pads,powderedcleaners,bleachor cleaners
containingbleachbecausetheseproductscan
scratchand weakenthepaint bmsh
Cleaningthelnside
Tohelp prevent odors, leave an open box of
baling soda m the fresh food and freezer
comparunents.
Unplugtherefrigeratorbefore cleaning,ff this
is not pracucal, wring excess mozsture out
of sponge or cloth when cleaning around
swttches, hghts or controls
Use warm water and baking soda soluuon--
about a tablespoon (15 m[) ofbaldng soda
to a quart (1 l) of water This both cleans
and neutrahzes odors. Rinse and _sape dry
After cleanmg die door gaskets, apply a
thin layer of petroleumjeny to the door
gaskets at the hinge side. This helps keep
the gaskets from snckmg and bending out
of shape.
Drain openingin freezer comportme_
Dunng },early cleaning, remove bottom
freezer basket and flush a soluuon of
baking soda----1 teaspoon (5 ml) and 2 cups
(500 ml) of hot (not botimg) water--
through the dram line with the help of a
meat baster. Thts wtll help ehmiuate odor
and reduce the hkehhood of a clogged
drmn line If drmn becomes clogged, use a
meat baster and baking soda soluuon to
force the clog through the drmn line.
Avoid cleaningcoldglass shelveswith hot water
becausetheextreme temperaturedifferencemay
causethem tobreak Handleglassshelves
carefully Bumpingtemperedglass cancause it to
shatter
Donotwashanyp/astlc refrlgerator parts in the
dishwasher
Condenser
There is no need for routine condenser
cleamng m normal home operatang
enwronments. However, in enwronments
that may be particularly dusty or greasy, the
condenser should be cleaned periodically
for efficient refrtgerator operauon.
Cleaningthecondenser.
The condenser is located instde die back
of the refrigerator. To access it, first unplug
the refrigerator. Then remove the access
cover The condenser ts on the nght stde.
11

Careandcleaningoftherefrigerator.
Behind the Refrigerator
Be careful when moving the refrigerator
away from the wall.All types of floor
coverings can be damaged, particularly
cushioned coveringsand those with
embossed surfaces.
Pull the refrigerator straight out and return
it to position by pushing it straight in.
Moving the refrigerator in a side direction
may result in damage to the floor covering
or refrigerator.
Whenpushingtherefrigeratorback,makesure
youdon'trolloverthepowercordor icemaker
supplyline(onsomemodels).
Preparing for Vacation
For long vacations or absences, remove
food and unplug the refrigerator. Clean the
interior with abaking soda solution of one
tablespoon (15 ml) of baking soda to one
quart (1 1) of water. Leave the doors open.
Set the icemaker power switch to the 0(off)
position and shut off the water supply to
the refrigerator.
If the temperature can drop below
freezing, have a qualified servicer drain the
water supply system (on some models) to
prevent serious property damage due to
flooding.
Preparing to Move
Secure all loose items such asgrille, shelves and drawersby taping them securely
in place to prevent damage.
Besuretherefrigeratorstaysin anuprightpositionduringmoving.
12

Replacingthelightbulbs.
Turning the control to the 0 (off) position does not remove power to the light circuit.
Fresh Food Compartment--Upper Light
0 Unplug the refrigerator.
O The bulb is located behind the controls.
Replace with an appliance bulb of the
same or lower wattage.
Plug the refrigerator back in,
Fresh Food Compar#nent--Lower Light Ionsomemodels)
This light is located above the top drawet 0 After replacing with an appliance
w bulb of the same or lower wattage,
Unplug the refrigerator, replace the shield.
Grasp the lip at the bottom of the light _ Plug the refrigerator back in.
shield and pull it up and forward.
Freezer Compartment
Unplug the refrigerator.
_ Remove the shelf just below light shield.
(The shelf will be easier to remove if it
is emptied first.)
Lift up on the light shield to remove.
_After replacing with an appliance
bulb of the same or lower wattage,
reinstall the shield by hanging it
from the three tabs.
Reinstall the shelf and plug the
refrigerator back in.
Dispenser
Unplug the refrigerator.
_The bulb is located on the dispenser
trader the cona'ol panel.
Remove the lightbulb by turning
it counterclockwise.
Replace the bulb with a bulb of the
same size and wattage.
Plug the refrigerator back in.
13

Installation
Instructions Refrigerator
Models 20,22,25
IQuestions?Call 800.GE.CARES(800.4322737)or Visitour Websiteat: www.GEAppliances.com
In Canada, call 1.800.361.3400orVisitour Website at: www.geappliances.ca I
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT - Savethese
instructions for local inspector's use.
• IMPORTANT -Observeall
governing codes and ordinances.
• Note to Installer _ Be sure to leave these
instructions with the Consumer.
•Note to Consumer _ Keep these instructions
for future reference.
•Skill level - Installation of this appliance requires
basic mechanical skills.
•Completion time - Refrigerator Installation
15 minutes
•Proper installadon is the responsibility of the
installer.
•Product failure due to improper installation is not
covered under the Warranty.
WATER SUPPLY TO THE ICEMAKER
(on some models)
If the refrigerator has an icemaker, it will have to be
connected to a cold water line. AGE water supply kit
(containing tubing, shutoff valve, fittings and
instructions) is available at extra cost from your dealer,
by visiting our Website at www.GEAppliances.com
(in Canada, at www.geappliances.ca) or from Parts
and Accessories, 800.626.2002.
REFRIGERATOR LOCATION
•Do not install the refrigerator where the temperature
will go below 60°F (16°C) because it will not run often
enough to maintain proper temperatures.
• Install it on a floor strong enough to support it fully
loaded.
CLEARANCES
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
• Sides 1/8" (4 mm)
• Top 1" (25 mm)
•Back 1" (25 mm)
Adoor clearance of 3/4" (19 mm) is needed for a 90 °
door opening which provides better access to the food
storage area.
ROLLERS
The milers have 3 purposes:
• Rollers adjust so the door closes easily when opened
about halfway.
• Rollers adjust so the refrigerator is firmly positioned
on the floor and does not wobble.
• Rollers allow you to move the refrigerator away from
the wall for cleaning.
To adjustthe rollers, remove the base grille by pulling it
out at the bottom.
Tuna the roller adjusting screws clockwise to raise the
refrigerator, counterclockwise to lower it. Use an
adjustable wrench (3/8" hex head bolt) or pliers.
To replace base grille, line up the clips on back of grille
between the bar and the bottom of the cabinet. Push
forward until grille snaps into place.
14

Installation Instructions
DOOR ALIGNMENT
After leveling, make sure that doors are even at the top.
To make the doo_ even, adjust the refrigerator door.
O Using a 5/16' socket wrench, turn the door adjusting
screw to the right to raise the door, to the left to lower
it. (A nylon plug, embedded in the threads of the pin,
prevents the pin from turning unless a wrench is
0 u_a.)
After one or two turns of the wrench, open and close
the fresh food door and check the alignment at the
top of the doors.
Toremovethebase "_h,_---_ I_
grige,openthedoors
andthen_11the
grillestraightout.
15

Installation Instructions
INSTALLING THE WATER LINE
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of
tubing you need. Approved plastic water supply lines
are GE SmartConnect TM Refrigerator Tubing
(WX08X10002, WX08X10006, _€_X08X10015 and
WX08X10025).
When connecting your refrigerator to a GE Reverse
Osmosis Water System, the only approved installation is
with a GE RVKit. For other reverse usmosis water
systems, follow the mamffacturer's recommendations.
If the water supply to the refrigerator is from a Reverse
Osmosis Water Filtration System AND the refrigerator
also has a water filter, use the refrigerator's filter bypass
plug. Using the refrigerator's water filtration cartridge
in conjunction with the RO filter can result in hollow
ice cubes and slower water flow from the water
dispenser.
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and
lead to water leakage or flooding. Call a qualified
plumber to correct water hammer before installing
the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the icemaker power switch is in
the 0 (Off)position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.
All installations must be in accordance with local
plumbing code requirements.
WHAT YOU WILL NEED
• Copper or GE SmartConnect TM Refrigerator Tubing
kit, 1/4" outer diameter to connect the refrigerator
to the water supply. If using copper, be sure both ends
of the tubing are cut square.
To determine bow much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add 8"
(2.4 m). Be sure there is sufficient extra tubing (about
8' [2.4 m] coiled into 3 turns of about 10" [25 cm]
diameter) to allow the refrigerator to move out from
the wall after installation.
GE SmartConnect TM Refrigerator Tubing Kits are
available in the following lengths:
2' (.6 m) - WX08XIO002
6' (1.8 m) - WX08X10006
15' (4.6 m) - WX08X10015
25" (7.6 m) - WX08XlO025
Be sure that the kit you select allows at least 8' (2.4 m)
as described above.
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartConnect TM Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Certain
types of plastic will crack or rupture with age and cause
water damage to your home.
16

Installation Instructions
WHAT YOU WILL NEED (CONT.)
• AGE water supply kit (containing tubing, shutoff
valve and fittings listed below) is available at extra
cost from your dealer or from Parts and Accessories,
800.626.2002.
•A cold water supply. The water pressure must be
between "20and 120 p.s.i. (1.4-8.2 bar) on models
without a water filter and between 40 and 120 p.s.i.
(2.8-8.2 bar) on models with a water filter.
•Power drill.
•1/2" or adjustable wrench.
•Straight and Phillips blade screwdriver.
•Two 1/4" outer diameter compression nuts and
2 ferrules (sleeves)--to connect the copper tubing
to the shutoff valve and the refrigerator
water valve
OR
• If you are using a GE SmartConnect TM Refrigerator
Tubing kit, the necessary fittings are preassembled to
the tubing.
• If your existing copper water line has a flared fitting
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refrigerator OR you can cut off the flared fitting
with a tube cutter and then use a compression fitting.
Do not cut formed end from GE SmartConnect TM
Refrigerator tubing.
•Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32" at the point of
connection to the COLD WATER LINE. Saddle-type
shutoffvalves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
Install the shutoff valve on the nearest frequently used
drinking water line.
SHUT OFF THE MAIN WATER
SUPPLY
Turn on the nearest faucet long enough to clear
the line of water.
[] CHOOSE THE VALVE LOCATION
Choose alocation for the valve that is easily
accessible. It is best to connect into the side of a
vertical water pipe. When it is necessary to connect
into a horizontal water pipe, make the connection
to the top or side, rather than at the bottom,
to avoid drawing off any sediment from the
water pipe.
[] DRILL THE HOLE FOR THE VALVE
Drill a 1/4" hole in the water pipe (even if using a
self-piercing valve) using a sharp bit. Remove any
burrs resulting from drilling the hole in the pipe.
Take care not to allow water to drain into the drill.
Failure to drill a 1/4" hole may result in reduced
ice production or smaller cubes.
17

Installation Instructions
INSTALLING THE WATER LINE (cont.)
[] FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe with
the pipe clamp.
PipeClamp
Saddle-TypeJ Cold
ShutoffValve WaterPipe
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
[] TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE: Do not overtighten or you may crush the
tubing. -Washer
PipeClamp
Clamg
[] ROUTE THE TUBING
Route the tubing between the cold water line and
the refrigerator.
Route the tubing through a hole drilled in the wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing
(about 8' [9.4 m] coiled into 3 turns of about 10"
[25 cm] diameter) to allow the refrigerator to move
out from the wall after installation.
CONNECT THE TUBING TO THE
VALVE
Place the compression nut and ferrule (sleeve) for
copper tubing onto the end of the tubing and
connect it to the shutoffvalve.
Make sure the tubing is fully inserted into the valve.
Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect TM
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut undl it is hand dght, then tighten
one additional turn with a wrench. Overtightening
may cause leaks.
Saddle-Type
ShutoffValve Sma_C0nnectTM
Tubing
PackingNut
OutletValve -- Ferrule(sleeve)
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
[] FLUSH OUT THE TUBING
Turn the main water supply on and flush out the
tubing until the water is clear.
Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.
18

Installation Instructions
[] CONNECT THE TUBING TO THE
REFRIGERATOR
NOTES:
•Before making the connection to the refrigerator,
be sure the refrigerator power cord is not
plugged into the wall outlet.
• If your refrigerator does not have a water filter,
we recommend installing one if your water supply
has sand or particles that could clog the screen of
the refrigerator's water valve. Install it in the
water line near the refrigerator. If using a GE
SmartConnect TM Refrigerator Tubing kit, you
will need an additional tube (WX08X10002)
to connect the fiher. Do not cut plastic tube
to install filter.
Some models have the refrigerator connection at
the end of tubing located outside the compressor
compartment access cover. On other models, the
compressor compartment access cover must be
removed in order to access the refrigerator
connection at the water valve.
On models using the refrigeration connection at
the water valve, remove the plastic flexible cap.
Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown. On a GE
SmartConnect Refrigerator Tubing kit, the nuts
are already assembled to the tubing.
[] CONNECT THE TUBING TO THE
REFRIGERATOR (CONT.)
Insert the end of the tubing into the refrigerator
connection as far as possible. While holding the
tubing, tighten the fitting.
For plastic tubing from a GE SmartConnect
Refrigerator Tubing kit, insert the molded end of
the tubing into the refrigerator connection and
tighten the compression nut until it is hand tight,
then tighten one additional turn with a wrench.
Overtightening may cause leaks.
Fasten the tubing into the clamp provided as
shown to keep it in position. You may need to pry
open the clamp.
One of the illustrations below will look like the
connection on your refrigerator.
Tubing
Clamp
1/4_
_ml_'e_i_
Nm
Ferrule
(sleeve} SmartConnectTM
Connection Tubing
1/4"
Tubing
FernJle
$rnartConnectTM
Connection Tubing
ff-0]TURN THE WATER ON AT THE
SHUTOFF VALVE
Tighten any connections that leak.
Reattach the access cover.
19

Installation Instructions
INSTALLING THE WATER LINE (cont.)
I_IPLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the
wall. Push the refrigerator back to the wall.
START THE ICEMAKER
Set the icemaker power switch to the I (on)position.
The icemaker will not begin to operate undl it
reaches its operating temperature of 15°F (-9°C)
or below. It will then begin operation automatically
if the icemaker power switch is in the I(on)position.
NOTE: In lower water pressure conditions, the
water valve may turn on up to 3 times to deliver
enough water to the icemaker.
20