dji MATRICE 30 Series User manual

Read this manual carefully before handling the parachute system.
Parachute and Circuit
Breaker System
DJI MATRICE 30

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Flying Eye is your partner in drone technology since 2009. We develop parachute systems since the
appearance of the drone regulation in 2012. Pyrotechnic system from aviation technology, you have the
most efficient and lightest system on the market.
Flying Eye could not be held responsible for any malfunction or inefficient operation.
We are at your disposal for any technical or commercial information.
PRESENTATION

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Flying Eye may suspend the warranty and disclaim any liability to anyone who fails to observe the basic safety
precautions set forth below. Flying Eye is not responsible for any damage or injury directly or indirectly related
to the use of the fireworks or by the use of fireworks that do not meet the safety requirements and standards.
- No other operation is permitted other than that specified in the manual.
- The device should only be used by (or under the supervision of) a responsible adult. Always keep the device out
of the reach of children. Do not let them play with it.
- Under no circumstances should you disassemble any part of the device, except during scheduled maintenance
and in accordance with the instructions in this manual.
- Do not place the device in a damp or wet environment and keep it away from UV light.
- Do not expose the system to low or high temperatures, strong shocks, contact with chemicals, acids, or long-
term storage in a humid or dusty environment. Incorrect use may cause the pyrotechnic cartridges to explode and
put your life in danger. The maximum temperature of use is 40°C and the minimum temperature of use is -15°C.
- The good condition of the parachute system must be checked before each use. Do not use the device if it is
damaged or malfunctioning. If this is the case, contact your dealer.
- The parachute cannot prevent the drone from malfunctioning.
- Any flight with a drone implies the existence of a risk for the equipment and people in the vicinity, with or without
a parachute.
- The use of a parachute should not increase your risk.
- The parachute must be activated manually by the user. Regular training is necessary to
to be able to react correctly in case of an emergency. Therefore, for the safety of the equipment and third parties,
practice dummy releases on the ground regularly.
- The ejection system works only once. It must be returned to your dealer to be recharged.
WARNINGS AND PRECAUTIONS FOR USE

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
DESCRIPTION :
Reliable and lightweight safety system for the S2 and S3 certification of the DJI MATRICE 30. It includes a
double ultra fast parachute, a circuit breaker, an alarm and a secure radio trigger that is attached to the
pilot's remote controller.
The parachutes are removable in a few seconds.
The center of gravity of the Matrice 30 is maintained. Redundancy of the parachutes for a totally infallible
system. The MATRICE 30 lands on its feet, when the parachutes are released, to avoid the breakage of an
arm or a landing gear. Works correctly from 15 meters high thanks to the pyrotechnic technology borrowed
from microlights.
Very low air penetration coefficient, which means that no vibrations are generated at high speeds, thus
maintaining a perfectly stable image.
Reliable, robust and light high-tech materials.
The assembly and disassembly of the system is doable by the customer. The system does not modify the
integrity of the DJI MATRICE 30. The DJI manufacturer's warranty is retained. Fits in the original case of the
Matrix 30.
TECHNICAL SPECIALIZATIONS :
- Weight of the complete system: 540g
- Impact energy: 61 J
- Approved for 4.9kg
- Redundancy of the power cut electronics
- Double trigger button on the remote control
- Safety pin for handling pyrotechnic charges
- Encrypted frames (256 bits) - checksum to authenticate the frame. Association in both directions.
- Remote control autonomy of 40 hours (1800mAh lipo battery rechargeable by USB-C)
- Auto power Off (after 30 minutes without connection)
- Battery voltage display on the remote control
- Backup power allowing to trigger the parachutes up to 1 minute after a loss of power of the drone
- Firmware update via USB-C
- Secure remote control power on and off (like a DJI system)
- Possibility to pair up to 4 remotes per drone
Each element of the kit can be purchased separately on our website: www.flyingeye.fr
TECHNICAL DESCRIPTION

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
CONTENT:
- 2 parachute pods
- 1 left exoskeleton
- 1 right exoskeleton
- 1 battery module
- 1 Buzzer
- 1 long screw
- 2 charging plugs
- 2 pyrotechnic charges
- 1 remote control
- 2 test leds
- 2 battery latches
- 1 locking screw for radio control support
- 1 remote control support
- 1 pin
- 2 electronic tabs

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Charge level of the radio control :
To check the charge level, press the "POWER" button once.
To check the charge level, press the "POWER" button once, the indicator lights will appear.
Switching on :
To switch on the radio control parachute, press and hold the "POWER" button.
"POWER" BUTTON.
Activation:
The parachute is released by pressing the 2 "FIRE" buttons simultaneously.
REMOTE CONTROL PARACHUTE

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
The different alerts on the remote controller of the system :
Operational system
Loss of connection with the drone
Safety pin in place
Missing pyrotechnic charge(s)
Triggering the system

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
OPERATING MODE
Take the following 3 pieces (and the M30 radio control):
Radio control Parachute RC support Support screw
Insert the RC bracket on the parachute radio control and screw the 2 small screws with an allen key
(supplied with the M30) as below:
Then attach it to the M30 radio control by inserting the 2 small pins of the RC bracket into the 2 holes (orange
arrows) and then insert the screw of the bracket into the thread of the M30 radio control (green arrow) as
below:
ASSEMBLY OF RADIO CONTROL PARACHUTE

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Installation of the battery locks:
Replace the original M30 locks with those supplied with the system and check the springs, be careful not
to invert the springs (left spring to left / right spring to right):
Then install the exoskeleton (right and left) on the M30:
INSTALLATION

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Insert the exoskeleton as below:
Then screw in the long screw to hold the exoskeleton in place on the M30 :
Insert the electronic tabs on the battery module as shown below:

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Insert it into the battery compartment of the M30 (all the way to the bottom), pushing the tabs slightly inwards so
that they do not rub against the side:
Then screw the tabs onto the exoskeleton:

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Then insert the buzzer (slightly at an angle) on the battery module and re-center it once inserted:
Insert the M30 batteries all the way in and lock them with the previously installed locks (keep the drone switched
off):

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Insert the pin before installing the pyrotechnic charges:

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Finally install the parachute pods:

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
Before each flight, you must check all the components of the system and verify its integrity. If any anomaly is
found, do not proceed with the flight and contact your dealer.
Test for proper operation on the ground:
- Ensure that the entire drone system is powered down. Batteries disengaged.
- Insert the safety pin
- Remove the "parachute" pods by unscrewing them.
- Remove the 2 pyrotechnic charges.
- Put in place the 2 test leds in place of the charges
- Put in place the 2 batteries and lock.
- Switch on the radio control of the drone.
- Switch on the radio control "parachute".
- Turn on the drone, the symbol appears.
- Remove the safety pin, the symbol appears.
- Switch on the drone's motors.
- Activate the "parachute" system by pressing the 2 "FIRE" buttons:
- The four motors stop. The 110dB buzzer sounds.
The symbol appears.
The two test leds light up for 2 seconds in red or green.
- The buzzer continues to sound as long as the batteries are in place.
- Unlock and remove the batteries:
The system will remain powered for about one minute and the buzzer will stop.
- Turn off both radio controls.
FUNCTIONAL TEST

OPERATING INSTRUCTIONS
FLYSAFE-M30
Version 1.05
Version matériel 1.05
20/01/2023
ANNUAL MAINTENANCE
Change of pyrotechnic charges every 12 months (contact dealer).
Ventilation of the sail for 24 hours, inspection of the cloth, lines and folding.
For an optimal functioning of the system, the annual maintenance of the sail is essential
(contact your dealer).
SPECIFIC MAINTENANCE :
You must dry the glider immediately after any contact with moisture or water to avoid any deterioration. Contact with
solvents, chemicals, or fuel may alter the mechanical properties of the canopy.
The canopy and lines should be cleaned only with soap-free water and then dried.
WARRANTY:
We guarantee our parachutes for one year from the date of purchase against any defect or design fault that may occur
during normal use of the product.
Any abusive or incorrect use, any exposure to aggressive factors (high humidity, high temperature...) which would lead to
damage will invalidate this warranty.
MAINTENANCE
STORAGE AND WARRANTY

Contact Us :
Flying Eye
80 route des lucioles
Bat. I14
06560 SOPHIA ANTIPOLIS
Mail : [email protected]
Phone : [phone]