dji Ronin Series Battery Power Distributor User manual

Intelligent Battery
Power Distributor
RONIN
Quick Start Guide
V1.2 2016.02

Disclaimer
Thank you for purchasing the Ronin Intelligent
Battery Power Distributor. Read this disclaimer
carefully before using this product. By using this
product, you hereby agree to this disclaimer and
signify that you have read it fully. Please use this
product in strict accordance with the manual
and be sure to pay attention to the warnings.
SZ DJI Technology Co., Ltd. and its affiliated
companies assume no liability for damage(s)
or injuries incurred directly or indirectly from
improper use of this product. Refer to the User
Manual for applicable information not herein
contained.
This device complies with Part 15 of the FCC
Rules.
DJI is the registered trademark of SZ DJI
Technology Co., Ltd. (abbreviated as “DJI”).
Names of product, brand, etc., appearing
in this manual are trademarks or registered
trademarks of their respective owner
companies. This product and manual are
copyrighted by DJI with all rights reserved.
No part of this product or manual shall be
reproduced in any form without the prior
written consent or authorization of DJI.
This disclaimer is produced in various
languages. In the event of divergence among
different versions, the Chinese version shall
prevail when the product in question is
purchased in Mainland China, and English
version shall prevail when the product in
question is purchased in any other region.
Product Prole
The Ronin Intelligent Battery Power Distributor
(the “power distributor”) provides two P-TAP
outlets for external lming equipment such as
RED cameras.

Overview
Installation
1. Before attaching the Intelligent Battery to the
power distributor, select the desired sound
option for the buzzer which is triggered
when the battery level drops below 10%.
Mounting Holes
Thumb Screws
Low Battery Warning
On/Off Switch
P-TAP Outlet
P-TAP Outlet
Battery Slot
Buzzer
2. Loosen the thumb screws on both sides of the
Intelligent Battery and then slide the battery
into the power distributor’s battery slot. Ensure
the connectors make good contact.

Ensure the Intelligent Battery is turned
off during installation.
Ensure the Intelligent Battery is firmly
installed and the connectors make
good contact. Failure to do so may lead
to poor power and signal transmission.
Skip this step if using the Ronin-M.
3. Tighten the thumb screws on the Intelligent
Battery to secure.
4. If you are installing onto the Ronin, use a hex
key to remove the four screws on both sides
of the Ronin battery buckle. Then mount
the new battery buckle onto the Ronin and
tighten the screws.
1
2

7. Connect your filming equipment to the
P-TAP outlets.
6. Tighten the thumb screws on the power
distributor to secure.
5. Loosen the thumb screws on both sides
of the power distributor. Slide the power
distributor into the battery slot of the Ronin
or Ronin-M. Ensure the connectors make
good contact.

This content is subject to change.
Download the latest version from
www.dji.com/product/ronin-m
If you have any questions about this document, please contact
DJI by sending a message to [email protected].
©2016 DJI. All Rights Reserved.
Mounting Holes
The power distributor can also be mounted on
other equipment using the two standard 7 mm
mounting holes.
Specications
Weight 125 g
Output Voltage 12 V
Output Current ≤8 A
Compatible
Batteries
844297-4350mAh-15.2V
824380-3400mAh-14.8V
423496-1580mAh-14.4V*
* If using the 423496-1580mAh-14.4V Intelligent
Battery, a motor stall may cause your external
equipment to unexpectedly shut down from the
sudden voltage drop.
22 mm
10.5 mm
7 mm
4.1 mm
13.2 mm